Journal of the Korean Society of Safety (한국안전학회지)

The Korean Society of Safety (한국안전학회)
권호 표지

FEM Analysis on Temperature Distribution and Thermal Stress of a Brake Drum for Large Commercial Vehicle

대형 상용차용 브레이크 드럼의 온도 분포 및 열응력에 관한 유한요소 해석

  • 김호경 (서울산업대학교 자동차공학과) ;
  • 이영인 (알테어 엔지니어링(주)) ;
  • 주세민 (알테어 엔지니어링(주))
  • Published : 2006.12.31
Download PDF
⟨ Previous Next ⟩

Abstract

A transient heat transfer and thermal stress analysis for a brake drum of commercial vehicles have been performed by ANSYS code in the cases of single braking and the repeated braking condition. The temperature and thermal stress distributions in the brake drum under various braking conditions were obtained using a two-dimensional axisymmetric model. In case of deceleration of 0.3G with an initial vehicle speed of 60km/h, the maximum temperature in the drum was $87.6^{\circ}C$ after braking application. The maximum stress of 78.7MPa in the drum occurred at the intersection between the flange and hat under a condition in which repeated 15 cycles braking with an initial vehicle speed of 60km/h and a deceleration of 0.3G is applied to according to KS R1129. The maximum stress value is much lower than the yield strength of drum material(FC250).

Keywords

References

  1. R. J. Ashworth, M. EL-Sherbiny, T. P. Newcomb, 'Temperature Distributions and Thermal Distortions of Brake Drum', Proc Instn Mech Engrs, Vol. 191, pp. 19-77, 1977
  2. A. J. Day, P. R. Harding, T. P. Newcomb, 'A Finite Element Approach to Drum Brake Analysis', Proc Instn Mech Engrs, Vol. 193, pp. 401-406, 1979
  3. D. C. Sheridan, J. A. Kutchey, and F. Samie, 'Approaches to the Thermal Modeling of Disc Brakes,' General Motors Research Laboratories, SAE 880256, pp. 4268 -4283, 1989
  4. C. Watson, T. P Newcomb, 'A Three Dimensional Finite Element Approach to Drum Brake Analysis', Proc Instn Mech Engrs, Vol. 204, pp. 93 -101, 1990
  5. 김기택, 임성무, 조진우, 인홍진, '브레이크 시스템의 응력 및 열전달 해석', 한국자동차공학회논문집, 96380215, pp. 391-396, 1996
  6. 조종두, '자동차 브레이크 설계요소', 대한기계학회논문집, 제 39권, 제 7호, pp. 49-57, 1997
  7. 김청균, 성부용, '급제동시 디스크 브레이크 시스템의 열적 거동 해석', 대한기계학회논문집, 제 22권, 제 6호, pp. 1106-1113, 1998
  8. KS R 1129, 트럭 및 버스 상용브레이크 실차 시험방법 및 브레이크 실차 요구 성능, 한국산업규격, 2000
  9. R. Limpert, 'Brake Design and Safety', Society of Automotive Engineers, Inc, pp. 111 -172, 1992
  10. K. Fuad, M. Daimaruya, and H. Kobayashi, 'Temperature and Thermal Stresses a Brake Drum Subjected to Cyclic Heating', Journal of Thermal Stresses, Vol. 17, pp. 515-527, 1994 https://doi.org/10.1080/01495739408946277
  11. Ramachandra Rao, and H. Ramasubrarnanian, 'Computer Modeling of Temperature Distribution in Brake Drumfor fade assessment. Proc. Inst. Mech. Engrs. 202:257-64, 1988
  12. J. Yamabe, M. Takai, T. Matsui, T. Kimura, M. Sasaki, 'Development of Disk Brake Rotors for Trucks with High Thermal Fatigue Strength', JSEA 20024017, pp. 105 -112, 2002