International Journal of Automotive Technology

  • 제7권4호
  • /
  • Pages.493-500
  • /
  • 2006
  • /
  • 1229-9138(pISSN)
  • /
  • 1976-3832(eISSN)
한국자동차공학회 (The Korean Society of Automotive Engineers)
권호 표지

DISTRIBUTION OF FUEL MASS AFTER WALL IMPINGEMENT OF DIESEL SPRAY

  • Ko, K.N. (Clean Energy Education Center, Cheju National University) ;
  • Huh, J.C. (Department of Mechanical Engineering, Cheju National University) ;
  • Arai, M. (Department of Mechanical System Engineering, Gunma University)
  • 발행 : 2006.06.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Investigation on the fuel adhering on a wall was carried out experimentally to clarify the characteristics of impinging diesel sprays. Diesel sprays were injected into a high-pressure chamber of cold state and impinged to a wall having various impingement distances and ambient pressures. Photographs of both the fuel film and the post-impingement spray were taken through a transparent wall. Adhered fuel mass on a wall was measured by means of dividing into two types of fuel state: the fuel film itself; and sparsely adhered fuel droplets. Adhering fuel ratio was predicted and further the distribution of fuel mass for impinging diesel spray was analyzed as a function of time. As result, with an increase of the ambient pressure, both the maximum fuel film diameter and the adhered fuel ratio decreased. Based on some assumptions, the adhering fuel mass increased rapidly until the fuel film diameter approached the maximum value, and then increased comparatively gradually.

키워드

참고문헌

  1. Amagai, K., Maruyama, Y., Saito, M. and Arai, M. (2003). Spray-to-spray interaction after wall impingement. SAE Paper No. 2003-01-1835
  2. Chikahisa, T., Hishinuma, Y. and Ushida, H. (2002). Mixing conditions with spray-jet interaction for effective soot reduction in diesel combustion. Int. J. Automotive Technology 3, 1, 17-25
  3. Gonzalez, D., Gonzalez, M. A., Borman, G. L. and Reitz, R. D. (1991). A study of diesel cold starting using both cycle analysis and multidimensional calculations. SAE Paper No. 910180
  4. Ko, K. N., Momiyama, T. and Arai, M. (2001). Effect of wall impingement on volumes of diesel sprays and their concentrations. Trans. Japan Society of Mechanical Engineers 67, 662, 216−222
  5. Koo, J. Y. (2003). The effect of injector nozzle geometry and operating pressure condition on the transient fuel spray behavior. J. Mechanical Science and Technology 17, 3, 617-625
  6. Matsuoka, S., Kamimoto, T. and Kobayashi, H. (1984). Photographic and image analysis studies of diesel spray and flame with a rapid compression machine and a D. I. diesel engine (Interpretation and Conceptual Image). SAE Paper No. 845009, 76−87
  7. Park, S. W. and Lee, C. S. (2003). Macroscopic structure and atomization characteristics of high-speed diesel spray. Int. J. Automotive Technology 4, 4, 157-164
  8. Saito, A., Kawamura, K., Watanabe, S., Takahashi, T. and Tuzuki, N. (1993). Analysis of impinging spray characteristics under high-Pressure fuel injection (1st report, measurement of impinging spray Characteristics). Trans. Japan Society of Mechanical Engineers 59, 566, 356-361
  9. Senda, J. Kanda, T., Al-Roub, M., Farrell, P. V., Fukami, T. and Fujimoto, H. (1997). Modeling spray impingement considering fuel film formation on the wall. SAE Paper No. 970047, 37−51
  10. Stanton, D. W. and Rutland, C. J. (1996). Modeling fuel film formation and wall interaction in diesel engines. SAE Paper No. 960628, 29−45
  11. Stanton, D. W. and Rutland, C. J. (1998). Multi-dimensional modeling of thin liquid films and spray-wall interactions resulting from impinging sprays. Heat and Mass Transfer, 41, 3037-3054 https://doi.org/10.1016/S0017-9310(98)00054-4
  12. Takasaki, K., Wakuri, Y., Maeda, K., Oyamada, T. and Hamasaki, K. (1994). Influence of fuel spray impingement on combustion in a D. I. diesel engine. The 3th Int. Sym. Diagnostics and Modeling of Combustion in Internal Combustion Engines, July 11−14, Yokohama, Japan, 269−274
  13. Tsunemoto, H., Ishitani H., Wakamatsu T. and Tanaka T. (1996). Process of mixture formation of impinging spray on the wall in a hole type nozzle. Trans. Japan Society of Mechanical Engineers 27, 2, 39−45
  14. Zurlo, J. R. and Chigier, N. (1991). Impinging diesel spray dynamics. Atomization and Sprays, 1, 303−318