한국재료학회지 (Korean Journal of Materials Research)

  • 제16권11호
  • /
  • Pages.668-675
  • /
  • 2006
  • /
  • 1225-0562(pISSN)
  • /
  • 2287-7258(eISSN)
한국재료학회 (Materials Research Society of Korea)
권호 표지
DOI QR코드

DOI QR Code

국부가압 다이캐스팅 공정에서 3차원 유동 및 응고해석을 통한 자동차 변속기 Gear Housing의 주조방안 설계 최적화

Optimization of Casting Design for Automobile Transmission Gear Housing by 3D Filling and Solidification Simulation in Local Squeeze Diecasting Process

  • Park, Jin-Young (Dept. of Material Engineering, Pusan National University) ;
  • Kim, Eok-Soo (Pusan R&D Center, Korea Institute of Industrial Technology) ;
  • Park, Yong-Ho (Dept. of Material Engineering, Pusan National University) ;
  • Park, Ik-Min (Dept. of Material Engineering, Pusan National University)
  • 발행 : 2006.11.27
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In the partial squeeze casting process, the filling behavior of liquid metal and solidification pattern in thick area have significant influence on the quality of casting products and die life. For the optimal casting design of automobile transmission gear housing, various analyses were performed in this study by using computer simulation code, MAGMAsoft and the simulation results were compared and analyzed with experimental results. By air pressure criteria, internal porosities caused by air entrap during the mold filling were predicted and reduced remarkably by modification of gating system. Also, optimal squeeze-time lag to apply partial squeeze pin in thick area was calculated and the castings was free from shrinkage defects with the result of solidification analysis. Consequently, casting design for automobile transmission gear housing was optimized and approved by Computer Tomography.

키워드

참고문헌

  1. Chang Ho Lee, Jae Kwon Choi and Tae Woon Nam, J. Kor. Foundrymen's Soc., 20(6), 400 (2000)
  2. C. P. Hong, J. Kor. Foundrymen's Soc., 15(1), 5 (1995)
  3. Nahad A. El-Mahallawy, Mohamed A. Taha, Engenius Pokora and Friedrich Klein, J. of Mat. Sci. and Tech., 73(1), 125 (1998)
  4. Jing Tao, Anzai Koichi and Niyama Eisuke, in Proceeding of the 3rd Pacific Rim International Conference on Modeling of Casting and Solidification Processes, (1996)
  5. Zhang Weishan, Xiong Shoumei and Liu Baicheng, J. of Mat. Sci. and Tech., 63(2), 707 (1997) https://doi.org/10.1016/S0924-0136(96)02711-2
  6. Jae Kyung Lee, Jeong Kil Choi and Chun Pyo Hong, J. Kor. Foundrymen's Soc., 18(6), 555 (1998)
  7. MAGMA Gibereitechnologie GmbH, MAGMASOFT User's Tutorial Manual., (1997)
  8. In Ho Choo, Sung Kon Yu and Jeong Kil Choi, J. Kor. Foundryrnen's Soc., 18(6), 578 (1998)

피인용 문헌

  1. Difference in Solidification Process between Al-Mg Alloy and Al-Si Alloy in Die-Casting vol.22, pp.2, 2012, https://doi.org/10.3740/MRSK.2012.22.2.82