초록
도로를 건설하는 궁극적인 목적은 운전자의 편의성을 고려해야 함에도 불구하고 지금까지의 도로선형설계시 도로 이용자인 운전자를 고려하지 않고 있는 실정이다. 운전자의 편의성은 시간적 측면에서 정시성 및 신속성을 고려하고 있지만, 더불어 부가적으로 고려되어야 할 요소로서 사고에 대한 안전성을 감안해야만 한다. 본 연구에서는 지방부 일반국도 4차선 단곡선부의 1차로를 대상으로 입체선형의 주행속도특성을 고려한 편경사 안전율을 산정하고자 한다. 첫째, 기하구조의 영향을 분석하기 위해 선행차에 의해 영향을 받지 않은 승용차의 주행속도를 조사하였다. 둘째, 종단선형의 영향과 평면선형의 영향을 조합하여 6개 구간, 즉 12개 지점에서 주행속도를 측정하여 주행속도 특성을 기초 통계 분석하였다. 섯째, 기초 통계 분석 결과를 바탕으로 최대편경사를 새로운 안전율(${\alpha}$)개념을 도입하여 주행속도를 고려한 편경사값을 산정하였다. 연구결과, 입체선형에서 승용차의 주행특성을 알 수 있었고, 이를 고려한 안전율을 제시할 수 있었다. 최대편경사를 산정함에 있어 본 연구의 결과인 3차원적 입체선형을 고려한 안전율을 적용한다면 도로설계시 운전자의 안전성을 향상시킬 수 있을 것으로 판단된다. 더불어, 본 연구의 범위를 확장하여 다양한 기하구조를 가진 도로구간에 대한 수집 분석한 후, 3차원적 입체선형을 고려한 모델이 개발되어야 할 것으로 판단된다.
The propriety between suppliers and demanders in geometric design is very important. Although the final purpose of constructing roads is to concern about the driver s comfort, unfortunately, it has not been considered so far. We've considered the regularity and quickness in considering driver's comfort but there should be considered the safety for the accident as well. If drivers are appeared to be more speeding than designer's intention, there will be needed some supplements to increase the safety rate for the roads. Even if both an upward and downward section are supposed to exist at the same time for solid geometry of the roads like this, it is true that the recent design for the 3-D solid geometry section has been done as flat 2-D and the minimum plane curve radius and the maximum cant have been decided just by calculating without considering operating speed between an upward and downward section at the same point. In this investigation, thus, I'd like to calculate the safety of the cant by considering the speed features of the solid geometry for the first lane of four lane rural roads. To begin with, we investigated the driving speed of the car, which is not been influenced by a preceding car to analyze the influence of the geometrical structure by using Nc-97. Secondly, we statistically analyzed the driving features of the solid geometry after comparing the 6 sections, that is, measuring the driving speed feature at 12 points and combining the influence of the vertical geometry and plane geometry to the driving speed of the plane curve which was researched before. Finally, we estimated the value of cant which considers the driving speed not by using it which has applied uniformly without considering it properly, though there were some differences between a designed speed and driving speed through the result of the basic statistical analysis but by introducing the new safety rate rule, a notion of ${\alpha}$. As a result of the research, we could see the driving features of the car and suggest the safety rate which considers these. For considering the maximum cant, if we apply the safety rate, the result of this experiment, which considers 3-D solid geometry, there'll be the improvement of the driver's safety for designing roads. In addition, after collecting and analyzing the data for the road sections which have various geometrical structures by expanding this experiment it is considered that there should be developed the models which considers 3-D solid geometry.
