대한기계학회논문집B (Transactions of the Korean Society of Mechanical Engineers B)

  • 제28권8호
  • /
  • Pages.895-901
  • /
  • 2004
  • /
  • 1226-4881(pISSN)
  • /
  • 2288-5324(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

평면충돌제트에 의한 단상 및 비등 열전달의 국소적 측정

The Local Measurements of Single Phase and Boiling Heat Transfer by Confined Planar Impinging Jets

  • 발행 : 2004.08.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Single-phase convection and nucleate boiling heat transfer were locally investigated for confined planar water jets. The detailed distributions of the wall temperature and the convection coefficient as well as the typical boiling curves were discussed. The curve for the single-phase convection indicated the developing laminar boundary layer, accompanied by monotonic increase of the wall temperature in the stream direction. Boiling was initiated from the furthest downstream as heat flux increased. Heat transfer variation according to the streamwise location was reduced as heat flux increased enough to create the vigorous nucleate boiling. Velocity effects were considered for the confined free-surface jet. Higher velocity of the jet caused the boiling incipient to be delayed more. The transition to turbulence precipitated by the bubble-induced disturbance was obvious only for the highest velocity, which enabled the boiling incipient to start in the middle of the heated surface, rather than the furthest downstream as was the case of the moderate and low velocities. The temperature at offset line were somewhat tower than those at the centerline for single-phase convection and partial boiling, and these differences were reduced as the nucleate boiling developed. For the region prior to transition, the convection coefficient distributions were similar in both cases while the temperatures were somewhat lower in the submerged jet. For single-phase convection, transition was initiated at $x/W{\cong}2.5$ and completed soon for the submerged jet, but the onset of transition was retarded to the distance at $x/W{\cong}6$ for the fee-surface jet.

키워드

참고문헌

  1. Webb, B. W. and Ma, C. -F., 1995, 'Single-Phase Liquid Jet Impingement Heat Transfer,' Advances in Heat Transfer, Vol. 26, No. 5, pp. 105-217 https://doi.org/10.1016/S0065-2717(08)70296-X
  2. Wolf, D. H., Incropera, F. P. and Viskanta, R., 1993, 'Jet Impingement Boiling,' Advances in Heat Transfer, Vol. 23, pp. 1-132 https://doi.org/10.1080/10407789308913659
  3. Vader, D. T., Incropera, F. P. and Viskanta, R., 1992, 'Convective Nucleate Boiling on a Heated Surface Cooled by an Impinging, Planar Jet of Water,' ASME J. Heat Transfer, Vol. 114, pp. 152-160 https://doi.org/10.1115/1.2911241
  4. Wolf, D. H., Incropera, F. P. and Viskanta, R., 1996, 'Local Jet Impingement Boiling Heat Transfer,' Int. J. Heat Mass Transfer, Vol. 39, pp. 1395-1406 https://doi.org/10.1016/0017-9310(95)00216-2
  5. Kamata, T., Kumagai, S. and Takeyama, T., 1988, 'Boiling Heat Transfer to an Impinging Jet Spurted into a Narrow Space: Part I, Space with an Open End,' Heat Transfer-Japanese Res., Vol. 17, No. 5, pp. 71-80
  6. Kamata, T., Kumagai, S. and Takeyama, T., 1988, 'Boiling Heat Transfer to an Impinging Jet Spurted into a Narrow Space: Part II, Space with a Limited End,' Heat Transfer-Japanese Res., Vol. 17, No. 4, pp. 1-11
  7. Miyasaka, Y. and Inada, S., 1980, 'The Effect of Pure Forced Convection on the Boiling Heat Transfer Between a Two-Dimensional Subcooled Water Jet and a Heated Surface,' J. Chem. Eng. Jpn, Vol. 13, pp. 22-28 https://doi.org/10.1252/jcej.13.22
  8. Wadsworth, D. C. and Mudawar, I., 1990, 'Cooling of a Multichip Electronic Module by Means of Confined Two-Dimensional Jets of Dielectric Liquid,' ASME J. Heat Transfer, Vol. 112, pp. 891-898 https://doi.org/10.1115/1.2910496
  9. Mudawar, I. and Wadsworth, D. C., 1991, 'Critical Heat Flux from a Simulated Chip to a Confined Rectangular Impinging Jet of Di-Electric Liquid,' Int. J. Heat Transfer, Vol. 34, pp. 1465-1479 https://doi.org/10.1016/0017-9310(91)90289-Q
  10. Wolf, D. H., 1993, 'Turbulent Development in a Free-Surface Jet and Impingement Boiling Heat Transfer,' Ph.D. Thesis, Purdue University, West Lafayette, IN, U.S.A. (1993)
  11. Kline, S. J. and McClintock, F. A., 1953, 'Describing Uncertainty in Single-Sample Experiments,' Mechanical Engineering, Vol. 75, pp. 3-8
  12. Wu, S. J., 2003, 'Single-Phase Convection and Boiling Heat Transfer of Confmed Impinging Jets,' Ph.D. Thesis, Yonsei University, Seoul, KOREA
  13. Yang, G, Choi, M. and Lee, J. S., 1997, 'Effects of Slot Jet Width on Jet Flow Structure and Heat Transfer Characteristics for Jet Impingement on Flat Plate,' Proc. KSME 1997 Spring Annual Meeting(B), pp. 619-624
  14. Yoon, S., Yang, G, Sohn, D. and Choi, M., 1999, 'An Experimental Study on Heat Transfer and Flow Characteristics of a Circular Impinging Jet on a Flat Plate: Effects of Nozzle Wall Thickness and Nozzle Exit Pressure,' Transactions of the KSME (B), Vol. 23, No. 10, pp. 1285-1295