Journal of the Korea Institute of Military Science and Technology (한국군사과학기술학회지)

The Korea Institute of Military Science and Technology (한국군사과학기술학회)
권호 표지

The effect of inlet air temperature for the cooling of the military electronic chip on the thermal conductive board

공기온도가 열전도성 기판 위에 탑재된 군용 전자칩 냉각에 미치는 영향

  • Published : 2002.07.01
Download PDF
⟨ Previous Next ⟩

Abstract

The conjugate heat transfer from the simulated module in a horizontal channel with the variation of inlet air temperature is experimentally investigated. The aim of this study is to estimate temperature difference between a module and inlet air. This study is performed with the variation of parameters that are inlet air temperature(Ti=25~$55^{\circ}C), thermal resistance( $R_c$=0.05, 4.11, 158 K/W), inlet air velocity(Vi=0.1~1.5m/s), and input power(Q=3, 7 W). The results show that the effect of inlet air temperature is little, at the case of using conductive board. And input power was most effective parameter on the temperature difference between module and Inlet air.

Keywords

References

  1. Nelson L. A., Sekhon K. S. and Fritz J. E., 1978, Direct Heat Pipe Cooling of a Semiconductor Devices, Int. Heat Pipe Conf., pp.373-376
  2. 이진호, 1999, 모듈에서 기판으로의 전도열전달을 고려한 혼합대류열전달, 경북대학교 박사학위논문
  3. Kamal Kumar Sikka, 1997, Heat spreaders and heat sinks for mixed convection electronic cooling, A dissertation presented to the faculty of the graduate school of Cornell University for the degree of Doctor of philosophy
  4. Graham, K. and Witzman, S., 1988, Analytical Correlation of Thermal Design of Electronic Packages, Cooling Technology for Electronic Equipment, pp.249-264
  5. Park, S. H., Nakayama, W., 1995, Conjugate-Mode Heat Transfer from a Module on the Base of a Parallel-Plate Channel to Forced Convective Air Flow, Trans. of the Japan Society of Mechanical Engineers, Vol.61, No.583, B, pp.1070-1077
  6. Nakayama, W., Park, S. H., 1996, Conjugate Heat Transfer from a single surface mounted block to forced convective air flow in a channel, Journal of Heat Transfer, Vol.118, pp.301-309 https://doi.org/10.1115/1.2825845
  7. 김의광, 백병준, 박복춘, 조병수, 1996, 돌출된 열원이 부착된 수직채널내 복합열전달, 대한기계학회 논문집(B), 제2권, 제20호, pp.741-751
  8. Riu, K. J., Lee, J. H., Park, S. H., 1998, Conjugate Heat Transfer from a Surface-Mounted Module to Mixed-Convective Air Flow in a Channel Floor, Proceeding of the KSME Spring Annual Meeting, pp.122-127
  9. Park, S. H., Lee, J. H., Riu, K. J., 1998, Conjugate Mode Heat Transfer to Mixed-Convective Air Flow From a Square Module Mounted on a Conductive Board, Proceeding of the KSME Fall Annual Meeting, pp.241-245
  10. Lee, J. H., Park, S. H., Riu, K. J., Bang, C. H., 2000, Mixed Convection transport from a Module on the Bottom Surface of Three Dimensional Channel, Trans. KSME (B) Vol.24, No.5, pp.632-639
  11. Shaw, H. J. and Chen, W. L., 1991, Study on the laminar mixed convective heat transfer in Three-Dimensional Channel With a Thermal Source, Journal of Electronic Packaging, Vol.113, pp.40-49
  12. 1995, Test Method Standard for Environmental Engineering Considerations (MIL-STD-810E), U.S Department of Defense
  13. 김인수, 1997, 온도규격 설정을 위한 한국의 온도분석, 국방과학연구소
  14. ASHRAE, 1981, American Society of Heating, Refrigerating and Air Conditioning Engineers, ASHRAE Handbook of Fundamentals
  15. 백창인, 이관수, 김우승, 1996, '돌출 열원을 갖는 3차원 밀폐공간 내에서의 자연대류-복사 복합열전달에 대한 실험적 및 수치적 연구', 대한 기계학회논문집(B), 제20권, 제10호, pp.3344-3354
  16. S. W. Churchill, R. Usagi, 1972, A general expression for the correlation of rates of transfer and other phenomena, AICHE Journal, vol.18, no.6, pp.1121-1128