Journal of Mechanical Science and Technology

  • 제16권9호
  • /
  • Pages.1137-1146
  • /
  • 2002
  • /
  • 1738-494X(pISSN)
  • /
  • 1976-3824(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지

Flow and Heat Transfer Measurements of Film Injectant from a Row of Holes with Compound Angle Orientations

  • Bumsoo Han (School of Mechanical & Aerospace Engineering, Seoul National University) ;
  • Sohn, Dong-Kee (School of Mechanical & Aerospace Engineering, Seoul National University) ;
  • Lee, Joon-Sik (School of Mechanical & Aerospace Engineering, Seoul National University)
  • 발행 : 2002.09.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

An experiment has been conducted on the flow and heat transfer characteristics of film coolant injected from a row of five holes with compound angle orientations of 35$^{\circ}$ inclination angle and 45$^{\circ}$ orientation angle. The Reynolds number based on the mainstream velocity and injection hole diameter 3.58${\times}$10$^4$. Three-dimensional velocity, film cooling effectiveness and heat transfer coefficient data are presented at three different mass flux ratios of 0.5, 1.0 and 2.0. Flow entrainment has been found between the vortices generated by adjacent injectants. The injectant with compound angle orientation entrains not only the mainstream boundary layer flow but also the adjacent injectant. Because of the flow entrainment, the injectant. With compound angle orientation is characterized by a single vortex while two bound vortices are usually observed in the case of simple angle injection. The strength of the secondary flow depends strongly on the mass flux ratio, which shows significant influence on the film cooling effectiveness and heat transfer coefficient.

키워드

참고문헌

  1. Ahn, J., Jung, I. S. and Lee, J. S., 2001a, 'Film Cooling from Two Rows of Holes with Opposite Orientation Angles (I) : Configuration Effect,' Transactions of KSME B, Vol. 25, pp. 1122-1130
  2. Ahn, J., Jung, I. S. and Lee, J. S., 2001b, 'Film Cooling from Two Rows of Holes with Opposite Orientation Angles (II) : Blowing Ratio Effect,' Transactions of KSME B, Vol. 25, pp. 1131-1139
  3. Eckert, E. R. G., 1984, 'Analysis of the Thermal Characteristics of Heated Turbulent Jets in crossflow,' ASME Journal of Engineering for Gas Turbines and Power, Vol. 106, pp. 206-213 https://doi.org/10.1115/1.3239536
  4. Ekkad, S. V., Zapata, D. and Han, J. C., 1997a, 'Heat Tansfer Coefficients over a Flat-Surface with Air and $CO_2$ Injection through Compound Angle Holes using a Transient Liquid Crystal Image Method,' ASME Journal of Turbomachinery, Vol. 119, pp. 580-586 https://doi.org/10.1115/1.2841161
  5. Ekkad, S. V., Zapata, D. and Han, J. C., 1997b. 'Film Effectiveness over a Flat-Surface with Air and $CO_2$ Injection through Compound Angle Holes using a Transient Liquid Crystal Image Method,' ASME Journal of Turbomachinery, Vol. 119, pp. 587-592 https://doi.org/10.1115/1.2841162
  6. Honami, S., Shizawa, T. and Uchiyama, A., 1994. 'Behavior of the Laterally Injected Jet in Film Cooling: Measurements of Surface Temperature and Velocity/Temperature Fields within the Jet,' ASME Journal of Turbomachinery, Vol. 116, pp. 106-112 https://doi.org/10.1115/1.2928264
  7. Kays, W. M. and Crawford, M. E., 1993, Convective Heat and Mass Transfer, 3rd ed., McGraw-Hill, p. 281
  8. Lee, S. W., Kim, Y. B. and Lee, J. S., 1995. 'Flow Characteristics and Aerodynamic Losses of Film-Cooling Jets with Compound Angle Orientations,' ASME Journal of Turbomachinery, Vol. 119, pp. 310-319 https://doi.org/10.1115/1.2841114
  9. Ligrani, P. M., Ciriello, S. and Bishop, D. T., 1992. 'Heat Transfer, Adiabatic Effectiveness and Injectant Distributions of a Single Row and Two Staggered Rows of Compound Angle Film-Cooling Holes,' ASME Journal of Heat Transfer, Vol. 114, pp. 687-701
  10. Ligrani, P. M. and Lee, J. S., 1996a. 'Film Cooling from Two Staggered Rows of Compound Angle Holes at High Blowing Ratios,' International Journal of Rotating Machinery, Vol. 2, pp. 201-208 https://doi.org/10.1155/S1023621X96000073
  11. Ligrani, P. M. and Lee, J. S., 1996b. 'Film Cooling from a Single Rows of Compound Angle Holes at High Blowing Ratios,' International Journal of Rotating Machinery, Vol. 2, pp. 259-267 https://doi.org/10.1155/S1023621X96000139
  12. Ligrani, P. M., Wiegle, J. M., Ciriello, S. and Jackson, S. M., 1994a 'Film-Cooling From Holes with Compound Angle Orientation : Part 1-Results Downstream of Two Staggered Rows of Holes with 3d Spanwise Spacing,' ASME Journal of Heat Transfer, Vol. 116, pp. 341-352 https://doi.org/10.1115/1.2911406
  13. Ligrani, P. M., Wiegle, J. M. and Jackson, S. M., 1994b. 'Film-Cooling from Holes with Compound Angle Orientation : Part 2-Results Downstream of a Single Row of Holes with 6d Spanwise Spacing,' ASME Journal of Heat Transfer, Vol. 116, pp. 352-362 https://doi.org/10.1115/1.2911407
  14. Mick, W. J. and Mayle, R. E., 1988. 'Stagnation Film Cooling and Heat Transfer Including its Effects within the Hole Pattern,' ASME Journal of Turbomachinery, Vol. 110, pp. 66-72 https://doi.org/10.1115/1.3262169
  15. Schmidt, D. L., Sen, B. and Bogard, D. G., 1996. 'Film Cooling With Compound Angle Holes : Adiabatic Effectiveness,' ASME Journal of Turbomachinery, Vol. 118, pp. 807-813 https://doi.org/10.1115/1.2840938
  16. Sen, B., Schmidt, D. L. and Bogard, D. G., 1996. 'Film Cooling with Compound Angle Holes : Heat Transfer,' ASME Journal of Turbomachinery, Vol. 118, pp. 800-806 https://doi.org/10.1115/1.2840937