대한기계학회논문집B (Transactions of the Korean Society of Mechanical Engineers B)

  • 제26권9호
  • /
  • Pages.1267-1275
  • /
  • 2002
  • /
  • 1226-4881(pISSN)
  • /
  • 2288-5324(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

흐름 영각에 따른 강제공랭 모듈 주위의 열전달 특성에 관한 연구

A Study on the Heat Transfer Characteristics Around a Surface-Mounted Air-Cooled Module for the Flow Angle-of-Attack

  • 발행 : 2002.09.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

An experimental study was performed to investigate adiabatic wall temperature and heat transfer coefficient around a module cooled by forced air flow. The flow angle of attack to the module were 0$^{\circ}$and 45$^{\circ}$. In the first method, inlet air flow(1~7m/s) and input power.(3, 5, 7W) were varied after a heated module was placed on an adiabatic floor(320$\times$550$\times$1㎣). An adiabatic wall temperature was determinated to use liquid crystal film. In the second method to determinate heat transfer coefficient, inlet air flow(1~7m/s) and the heat flux of rubber heater(0.031~0.062W/$m^2$) were varied after an adiabatic module was placed on rubber heater covering up an adiabatic floor. Additional information is visualized by an oil-film method of the surface flow on the floor and the module. Plots of $T_{ad}$ and $h_{ad}$ show marked effects of flow development from the module and dispersion of thermal wake near the module. Certain key features of the data set obtained by this investigation may serve as a benchmark for thermal-design codes based on CFD.

키워드

참고문헌

  1. Chang, M. J., Shyu, R. J. and Fang, L.J., 1987, 'An Experimental Study of Heat Transfer from Surface Mounted Components to a Channel Airflow,' ASME Paper No. 97-HT-75
  2. Roeller, P. T., Stevens, J. and Webb, B. W., 1991, 'Heat Transfer and Turbulent Flow Characteristics of Isolated Three-Dimensional Protrusions in Channels,' ASME J. of Heat Transfer, Vol. 113, pp. 597-603 https://doi.org/10.1115/1.2910607
  3. Rosten, H. I. and Viswanath, R., 1994, 'Thermal Modeling of the Pentium TM Processor Package,' IEEE Electronic Component Technology Conf., Washington, D.C., pp. 421-428
  4. Behnia, M., Nakayama, W. and Wang, J., 1998, 'CFD Simuation of Heat Transfer from a Heated Module in an Air Stream: Comparison with Experiments and a Parametric Study,' InterSociety Conf. on Thermal Phenomena, pp. 143-151
  5. Chyu, M. K. and Natrajan, V., 1991, 'Local Heat/Mass Transfer Distributions on the Surface of a Wall-Mounted Cube,' ASME Journal of Heat Transfer, Vol. 113, pp. 851-857 https://doi.org/10.1115/1.2911213
  6. Nakamura, H., Igarashi, T. and Tsutsui, T., 2001, 'Local Heat Transfer Around a Wall-Mounted Cube in the Turbulent Boundary Layer,' Int. J. of Heat Mass Transfer, Vol. 44, pp. 3385-3395 https://doi.org/10.1016/S0017-9310(01)00009-6
  7. Natarajan, V. and Chyu, M. K., 1994, 'Effect of Flow Angle-of-Attack on the Local Heat/Mass Transfer from a Wall-Mounted Cube,' Trans. ASME, J. Heat Transf., Vol. 116, pp. 552-560 https://doi.org/10.1115/1.2910906
  8. Nakamura, H. and Igarashi, T. and Tsutsui, T., 1999, 'Local Heat Transfer Around a Wall-Mounted Cube(The Case of the Attack Angle of $45^{circ}$),' JSME B, Vol. 65-639, pp. 3771-3776
  9. Ramadhyani, S., Moffat, D. F. and Incropera, F. P., 1985, 'Conjugate Heat Transfer from Small Isothermal Heat Sources Embedded in a Large Substrate,' Int. J. of Heat Mass Transfer, Vol. 28, No. 10, pp. 1945-1952 https://doi.org/10.1016/0017-9310(85)90216-9
  10. Moffat, D. F., Ramadhyani, S. and Incropera, F.P., 1986, 'Conjugate Heat Transfer from Wall Embedded Sources in a Rectangular Channel,' ASME HTD-57, pp. 177-182
  11. Ortega, A., Ramanathan, S., Chicci, J. D. and Prince, J. L., 1993, 'Thermal Wake Models for Forced Air Cooling of Electronic Components,' Proc. 9th IEEE SEMI-THERM Symposium, pp. 63-74 https://doi.org/10.1109/STHERM.1993.225330
  12. Davalath, J. and Bayazitoglu, T., 1987, 'Forced Convection Cooling Across Rectangular Blocks,' ASME J. of Heat Transfer, Vol. 109, pp. 321-328 https://doi.org/10.1115/1.3248083
  13. Zebib, A. and Wo, Y. K., 1989, 'A Two-Dimensional Conjugate Heat Transfer Model for Forced Air Cooling of an Electronic Device,' ASME J. of Electronic Packaging, pp. 171-178
  14. Nakayama, W. and Park, S. H., 1996, 'Conjugate Heat Transfer from a Single Surface-Mounted Block to Forced Convective Air Flow in a Channel' ASME J. of Heat Transfer, Vol. 118, pp. 301-309 https://doi.org/10.1115/1.2825845
  15. Lee, J. H., Park, S. H. Riu, K. J. and Bang, C. H., 2000, 'Mixed Convection Transport from a Module on the Bottom Surface of Three Dimensional Channel,' Trans. of the KSME, Vol. 24, No. 5, Part B, pp. 632-639
  16. Yun, B. T. and CHoi, D. H., 1999, 'Analysis of Three-Dimensional Mixed Convection Flow About Uniformly Distributed Heat-Generating Blocks on a Conductive Wall,' Trans. of the KSME, Vol. 23, No. 1, Part B, pp. 1-11
  17. Hunt, J. C. R., Aell, C. J., Peterka, J. A. and Woo, H., 1978, 'Kinematical Studies of the Flows Around Free or Surface-Mounted Obsta-Applyng Topology to flow Visualization,' J. of Fluid Mechanics, Vol. 86, Part 1, pp. 179-200 https://doi.org/10.1017/S0022112078001068
  18. Baker, J. C., 1979, 'The Laminar Horseshoe Vortex,' J. of Fluid Mechanics, Vol. 95, Part.2, pp. 347-367 https://doi.org/10.1017/S0022112079001506
  19. Hunt, J. C. R., Lalas, D. P. and Asimakopoulos, D. N., 1984, 'Air Flow and Disperison in Rough Terrain : A Report on Euromech 173,' J. of Fluid Mechanics, Vol. 142, pp. 202-216 https://doi.org/10.1017/S0022112084001063
  20. Hasan, M. A. Z., 1989, 'The Near Wake Structure of a Square Cylinder,' Int. J. Heat and Fluid Flow, Vol. 10, No. 4, pp. 339-348 https://doi.org/10.1016/0142-727X(89)90024-6
  21. Kline, S. J., 1985, 'The Purposes of Uncertainty Analysis,' ASME J. of Fluid Engineering, Vol. 107, pp. 153-160 https://doi.org/10.1115/1.3242449