DOI QR코드

DOI QR Code

Design Considerations and Pull-Out Behavior of Mechanical Anchor of Reinforcement

철근 기계적 정착장치의 설계 고려사항과 인발특성

  • Published : 2001.12.01

Abstract

In RC structure, sufficient anchorage of reinforcement is necessary for the member to produce the full strength. Generally, conventional standard hook is used for the reinforcement's anchorage. However, the use of standard hook results in steel congestion, making fabrication and construction difficult. Mechanical anchor offers a potential solution to these problems and may also ease fabrication, construction and concrete placement. In this paper, the required characteristics and the design considerations of mechanical anchor were studied. Also, the mechanical anchor was designed according to the requirements. To investigate the pull-out behavior and properness of mechanical anchorage, pull-out tests were performed. The parameters of tests were embedment length, diameter of reinforcement, concrete compressive strength, and spacing of reinforcements. The strengths of mechanical anchor were consistent with the predictions by CCD method. The slip between mechanical anchor and concrete could be controlled under 0.2mm. Therefore, the mechanical anchor with adequate embedment could be used for reinforcement's anchorage. However, it was observed that the strength of mechanical anchors with short spacing of reinforcements was greatly reduced. To apply the mechanical anchor in practice (e.g. anchorage of the beams reinforcements in beam-column joint), other effects that affect the mechanical anchor mechanism, such as confinement effect of adjacent member from frame action or effects of shear reinforcement, should be considered.

철근콘크리트구조에서 철근의 인장력이 발휘되기 위해서는 적절한 정착길이 또는 갈고리가 필요하다. 그런데, 접합부와 같이 배근이 집중되는 곳이나 대구경 고강도철근이 필요한 경우 정착을 위한 정착길이나 갈고리의 제작 및 배근작업이 어려우며 콘크리트의 충진성도 저하될 수 있다. 또한 갈고리부분의 과도한 응력집중으로 국부적인 지압파괴나 slip이 발생될 우려도 있다. 이러한 문제점을 해결할 수 있는 방안으로 정착판을 철근 단부에 부착한 기계적 정착공법이 제안되고 있다. 본 연구는 기계적 정착공법의 기초가 되는 정착장치의 요구성능과 정착설계법을 고찰하고 인발실험를 통해 정착장치의 앵커기능을 확인하고자 한다 인발실험 결과, 본 연구에서 설계된 정착장치는 앵커로써의 기능을 적절히 발휘하여 기존 CCD 이론식과 매우 근접한 내력을 발휘하였다 철근항복내력 이상의 정착내력을 지니는 경우, 항복하중까지 콘크리트에 아무런 손상이 발생되지 않았으며, 정착판 후미에서 콘크리트와의 상대변위는 0.2mm이하로 콘크리트에 손상을 유발시키지 않을 것으로 판단되었다. 따라서, 본 연구의 설계과정으로 제작된 기계적 정착장치를 통해 콘크리트에 유해한 손상 없이 필요한 정착내력을 확보할 수 있다. 그러나, 철근간 간격이 좁아 파괴면이 중첩되는 경우에는 정착내력이 크게 저하되어, 순수한 콘크리트 내력만으로 기계적 정착설계가 이루어지는 경우 상당한 매립깊이가 요구된다. 따라서, 실제 구조물의 정착설계를 위해서는 인접부재와의 골조거동(frame action)에 따른 구속효과와 전단보강근의 영향을 고려할 필요가 있다. 이에 대한 추가적인 연구가 필요하다.

Keywords

References

  1. 콘크리트 구조설계기준 한국콘크리트학회
  2. Building Code Requirements for Reinforced concrete ACI 318-99
  3. Concrete International Anchoring with Dobule-Head Studs Amin G.;Walter H.D.
  4. Concrete International T-Headed Stirrup Bars Dale E. berner;Ben C. Gerwick Jr.;George C. Hoff
  5. 콘크리트학회지 v.13 no.1 철근의 기계적 정착 천성철;정석창;김대영;김상구
  6. T-Headed Bars v.13 no.5 HRC DALE E. BERNER;BEN C. GERWICK JR.;GEORGE C. HOFF
  7. LENTON Terminator Erico
  8. ネヅコン定着工法の設計·施工要領 神戶製鋼
  9. 日本建築センタ一 一般評價 BCJ-C2280 プレ一トナット工法 設計施工指針 東京鐵鋼朱式會社
  10. Appendix B-Steel Embedments Code Requirements for Nuclear Safety Related Concrete Structures ACI 349-97
  11. ACI Structural Journal v.92 no.1 Concrete Capapcity Design(CCD) Approach for Fastening to Concrete Werner F.;Rolf E.;John E.B.
  12. ACI Structural Journal v.96 no.5 Anchorage Capacity in Concrete of Headed Reinforcement with shallow Embed- ments DeVries R.A;Jirsa J.O.;Bashandy T.
  13. Recommendations for Design of Beam-Column Joints in Monolithic Reinforced Concrete Structures ACI-ASCE Committee 352
  14. 스웨이징에 의한 나사이음철근 NT신기술 1999-46호
  15. 鐵筋繼手性能判定基準 日本建築センタ一
  16. 付着.定着WG硏究成果報告書
  17. Shear Reinforcement for Slabs v.421 ACI