Porcelain Laminate veneer 절연 피복시 설측 연장 길이에 따른 파절강도의 연구

THE STUDY OF FRACTURE STRENGTH OF PORCELAIN LAMINATE VENEER WITH VARIOUS LINGUAL EXTENTION LENGTH WHEN LNCISAL RESTORING

개교증, 절연부 파절, 변색등 심미적 요인으로 라미네이트를 설측연장시 연장길이에 따른 파절강도를 알아보기위해 발거된 60개의 상악 전치의 순면에 3개의 seating form을 형성하고sheet wax를 사용하여 가로 5mm $^*$세로 5mm $^*$두께 0.9mm의 block을 형성하고, 각 군에 따라 I군 : 0.5mm, II군 : 1mm, III군 : 2mm, IV군 : 0mm로 설측 연장 길이를 달리하여 block을 형성 이를 인상채득하여 내화모형을 제작하였다. 여기에 라미네이트용 도재를 2회에 걸쳐 축성 통법대로 소성 제작하였다. block에 맞추어 contouring하고, 내화매몰재를 제거 sandblast처리를 시행하였다. 그후 레진시멘트로 합착하였다. 절치간 각도를 127도로 특별히 제작된 holding device를 이용하여 인스트론 만능시험기에 시편을 거상하고, 분당 0.5mm cross head speed로 파절강도를 측정하여 다음과 같은 결과를 얻었다. 1. 각 군의 평균파절강도는 대조군인 설면으로 연장치 않은 IV군에서 86.95Mpa, 0.5mm 연장한 I군에서 44.98Mpa, 1.0mm연장한 II군에서 27.47Mpa, 2.0mm연장한 III군에서 19.61Mpa의 순으로 나타났다. 2. 모든 실험군 사이에는 통계적으로 유의성 있는 차이를 나타냈고(p<0.01), 이러한 실험 결과로 미루어 보아 라미네이트 디자인시, 설면으로 연장치 않거나, 절연부의 피개가 불가피한 경우에는 설면으로 0.5mm 연장하는 것이 파절 강도면에서 유리하다고 사료된다.

The purpose of this study was to evaluate the fracture strength of porcelain laminate veneer with various lingual extention length when incisal restoring. Sixty recently extracted, intact maxillary incisors were used and stored in a physiologic saline solution from the time of extraction. Seating form was preparation at the labial surface of each tooth with a water-cooled round diamond bur. Standard block was formed with 32 gauge and 24 gauge wax at tooth labial and lingual surface. Lingual extention length differed according to each group. (group I : 0.5mm, group II : 1 mm, group III : 2mm, group IV : 0mm) All tooth specimens were impressioned with examix(GC Inc., Japan). Refractory cast were maked with refractory die material(Ceramco Inc., U.S.A.) Laminate porcelain (Ceramco II Veneer porcelain, Ceramco Inc., U.S.A.) was condensed in refractory die cast and baked according to the manufacturer's recommendations. Each surface was contoured with low speed diamond bur according to guide block. All porcelain specimens were sandblasted and ultrasonically cleaned in distlled water for 3 minutes. Then, all porcelain specimen were etched with 8% hydrofluoric acid for 5 minutes. Sixty specimens were bonded with composite resin cement(Choice Porcelain Veneer System, Bisco Inc., U.S.A.) according to manufacture's directions. The fracture loads of the specimen were measured by Instron universal testing machine. The mean values of fracture loads for the groups were statistically compared by Duncan's multiful range test. The result were as follows : Mean fracture strengths of each group were 86.95Mpa in no lingual extention group, 44.98Mpa in 0.5mm lingual extention group, 27.47Mpa in 1mm lingual extention group, 19.61Mpa in 2mm lingual extention group. There was a statistically significant difference between all group(p<0.01).