• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.139-139
• /
• 2017

최근 환경오염 문제로 인한 연비 규제 강화 속도가 빨라지고 있으며 이에 따른 연비 향상 기술이 크게 대두 되고 있다. 연비 향상 기술 중 경량화 방안소재로 알루미늄(Al), 마그네슘(Mg) 등의 비철금속을 주로 사용하고 있으며, 이중 알루미늄은 다른 경량화 금속소재보다 우수한 경쟁력을 가지고 있다. 하지만 경제적인 측면에서 철 대비 비용적인 어려움을 가지고 있고 용접성이 떨어지기 때문에, 자동차 부품의 일부만 알루미늄 소재를 선택하여 사용하고 있는 실정이며 알루미늄의 높은 이온화 경향으로 인해 기존 자동차 철강 소재와 접촉 시 쉽게 부식되는 단점을 가지고 있다. 이러한 문제점을 해결하기 위해서는 알루미늄의 금속원소를 첨가하는 연구가 지속적으로 개발 되고 있다. 알루미늄 합금에서 마그네슘의 첨가는 좋은 용접성과 내식성, 강도를 향상시킨다. 하지만 3%이상의 마그네슘 첨가는 입계에 ${\beta}(Al_xMg_y)$석출상이 석출되게 되며, 입계에 연속적으로 형성된 ${\beta}(Al_xMg_y)$석출상은 응력 부식 균열 (Stress corrsion cracking)과 입계 부식(Intergranular corrosion)을 야기하는 결과를 가져온다고 알려져 있다. 이 문제를 해결하기 위해 Al 5000계열 합금의 Zn의 첨가를 통해 ${\tau}(Al_xMg_yZn_z)$을 입계에 석출시켜서 입계에 ${\beta}(Al_xMg_y)$상의 석출을 방지함으로써 내식성을 향상시키거나 Al 5000계열 합금의 열처리를 통해 ${\beta}(Al_xMg_y)$석출상을 고용시킴으로써 응력부식균열의 발생을 억제하는 연구도 있다. 하지만 열처리 후 Polarization test를 이용한 내식성 연구는 잘 안 알려져 있다. 따라서 이번 연구에서는 Al5000계열의 주조한 합금을 DSC분석을 통하여 ${\beta}(Al_xMg_y)$석출상의 고용 온도가 약 $470^{\circ}C$라는 것을 확인한 후, 실온에서 $100^{\circ}C/hr$으로 가열하고 조건에 따라 $450^{\circ}C$에서 3시간, 6시간, 12시간, 24시간, 30시간 항온 유지시킨 후 공냉을 진행하였다. 열처리를 마친 시편은 에폭시를 이용하여 마운팅 하였으며, 시편표면을 2000#까지 연마 후 증류수로 세척한 다음 질소를 이용하여 건조 후 분극 시험을 진행하였다. 3.5wt% NaCl 용액에서 분극 곡선을 통해 부식거동을 확인한 결과 24시간까지 시간이 증가 할수록 내식성이 우수해지는 것을 확인하였으며, 추가적으로 조직사진, SEM & EDS 분석과 XRD, TEM 분석을 통해 내식성은 입계에 존재하는 Mg의 조성이 감소하게 되면 내식성이 향상되는 것을 관찰하였다.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.23 no.4
• /
• pp.388-396
• /
• 2020

Purpose: Impaired intestinal mucosal integrity may affect the gastrointestinal function, especially in relation to nutrition, absorption, and barrier function. The purpose of this study was to measure the prevalence of impaired intestinal mucosal integrity in presumed healthy children aged 1-3 years and assess the effects of zinc, glutamine, fiber, and prebiotic supplementation in them. Methods: A cross-sectional study was conducted in 200 children aged 1-3 years in Pasar Minggu, South Jakarta, Indonesia. A randomized double-blind parallel group method clinical trial was then performed to assess the effects of zinc, glutamine, fiber, and prebiotic supplementation. Results: Elevated calprotectin was found in 91/200 subjects (45.5%) at the onset of the study. After 10 months, 144 subjects completed the study: 72 subjects received the trial formula, whereas the other 72 received the standard formula. A transitory decrease in fecal calprotectin (FC) was observed after 6 months in the subgroup with normal FC levels, who were fed the test formula (p=0.012). Conclusion: The prevalence of impaired intestinal mucosal integrity in this group of Indonesian children aged 1-3 years was high. Supplementation with zinc, glutamine, fiber, and prebiotics during 6 months reduced FC only in those who had low levels at baseline but not in those with impaired integrity.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.30 no.1
• /
• pp.38-49
• /
• 1988

This paper presented as follows results of laboratory model tests with various shaped footings on soil bed reinforced with the strips on the base of behaviour of soil structure according to the loads and triaxial test results reinforced with geotextiles. Their parameters studied were the effects on the bearing capacity of a footing of the first layer of reinforcement, horizontal and vertical spacing of layers, number of layers, tensile strength of reinforcement and iclination load to the vertical 1.Depending on the strip arrangement, ultimate bearing capacity values could be more improved than urreinforced soil and the failure of soil was that the soil structure was transfered from the macrospace to microspase and its arrangement, from edge to edge to face to face. 2.The reinforcement was produced the reinforcing effects due to controlling the value of factor of one and permeable reinforcement was never a barrier of drainage condition. 3.Strength ratio was decreased as a linear shape according to increment of saturation degree of soil used even though at the lower strength ratio, the value of M-factor was rot influenced on the strength ratio but impermeable reinforcement decreased the strength of bearing capacity. 4.Ultimate bearing capacity under the plane-strain condition was appeared a little larger than triaxial or the other theoretical formulars and the circular footing more effective. 5.The maximum reinforcing effects were obtained at U I B=o.5, B / B=3 and N=3, when over that limit only acting as a anchor, and same strength of fabric appeared larger reinforcing effects compared to the thinner one. 6.As the LDR increased, more and more BCR occurred and there was appeared a block action below Z / B=O.5, but over the value, decrement of BCR was shown linear relation, and no effects above one. 7.The coefficient of the inclination was shown of minimum at the three layers of fabrics, but the value of H / B related to the ultimate load was decreased as increment of inclination degree, even though over the value of 4.5 there wasn't expected to the reinforcing effects As a consequence of the effects on load inclination, the degree of inclination of 15 per cent was decreased the bearing capacity of 70 per cent but irnproved the effects of 45 per cent through the insertion of geotextile.

• Korean Journal Plant Pathology
• /
• v.14 no.5
• /
• pp.445-451
• /
• 1998

A severe Phytophthora rot of strawberry caused by a species of Phytophthora has been widely occurred at major cultivation areas of Kimhae on August in 1997. Incidence of the disease was obtained in the range of 69.2~83.6% in surveyed 4 fields and showed an average of 75.2%. A species of Phytophthora was mostly isolated from the crown of infected strawberry plants and all the isolates were identified as P. nicotianae var. nicotianae (=P. parasitica). The fungus showed strong pathogenicity on strawberry by inoculation test. As a result of the leaf inoculation using mycelial disks of the fungus, both leaves and petioles were darkly browned, and were finally blighted. As a result of the root inoculation of zoospore suspension, both roots and crowns were rotten with dark brown. Although the fungus produced sporangia either on V-8 juice agar medium or liquid medium, the sporangia observed on the liquid medium appeared to be broadly turbinate and noncaducous. Moreover the fungus cultured on the liquid medium often produced sporangia having two papilla. The number of zoospores in sporangia was found to be ranged from 3 or 4 to as many as 20 or 25. In addition, the released zoospore from the sporangium became the cystospore during the prolonged culture of the fungus. The sporangia were measured as av. 49$\times$35 ${\mu}{\textrm}{m}$ with l/b ratio of 1.43. All isolates from crowns were heterothallic and A1 mating type since oospores were abundantly formed on clarified V-8 juice agar by dual culture with P. capsici A2 mating type. Aplerotic oospores were sized 24-26 ${\mu}{\textrm}{m}$. Antheridia were always amphigynous and recoreded an average of 12$\times$10 ${\mu}{\textrm}{m}$. Hyphal swlling were easily observed, and terminal or intercalary chlamydospores were abundantly formed on V-8 juice agar as well as in C/Z solution and sized av. 28.2 ${\mu}{\textrm}{m}$. This is the first report of Phytophthora rot of strawberry in Korea.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.309-313
• /
• 2006

Many researchers have studied on the lightness of automobile. These researches are such as a body shell, sub frame, fuel tank, engine etc. The transmission Part is a magnitude one in the aspect of weight. A drive shaft (propeller shaft) transmits the engine power to rear differential gear assembly. It is used in the compact car that is a single drive shaft. But in the case of long body cars such as SUV (Sports Utility Vehicle), truck and large vehicle, two or three divided drive shaft are used to prevent the vibration damage from a drive shaft that has been taken high torsion and rotation. This multi-divided drive shaft structure is so heavy because it is assembled by yoke, center bearing and solid spline axis. When the rear axle move up and down, the spline shaft adjust the variation of a length between the transmission and rear axle gearbox. In this paper, it is studied in the experimental method that is a bending vibration characteristic of slip in tube shaped propeller shaft. This type propeller shaft is developed to combine the spline axis with drive shaft and can be light in weight of transmission part.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.4
• /
• pp.581-589
• /
• 2015

This paper describes a monocular vision-based formation flight technology using two fixed wing unmanned aerial vehicles. To measuring relative position and attitude of a leader aircraft, a monocular camera installed in the front of the follower aircraft captures an image of the leader, and position and attitude are measured from the image using the KLT feature point tracker and POSIT algorithm. To verify the feasibility of this vision processing algorithm, a field test was performed using two light sports aircraft, and our experimental results show that the proposed monocular vision-based measurement algorithm is feasible. Performance verification for the proposed formation flight technology was carried out using the X-Plane flight simulator. The formation flight simulation system consists of two PCs playing the role of leader and follower. When the leader flies by the command of user, the follower aircraft tracks the leader by designed guidance and a PI control law, and all the information about leader was measured using monocular vision. This simulation shows that guidance using relative attitude information tracks the leader aircraft better than not using attitude information. This simulation shows absolute average errors for the relative position as follows: X-axis: 2.88 m, Y-axis: 2.09 m, and Z-axis: 0.44 m.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.165-170
• /
• 2014

PURPOSE. This study was aimed to evaluate effect of the desensitizing pretreatments on the micro-tensile bond strengths (${\mu}TBS$) to eroded dentin and sound dentin. MATERIALS AND METHODS. Forty-two extracted molars were prepared to form a flat dentin surface, and then they were divided into two groups. Group I was stored in distilled water while group II was subjected to a pH cycling. Each group was then subdivided into three subgroups according to desensitizing pretreatment used: a) pretreatment with desensitizer (Gluma); b) pretreatment with $CO_2$ Laser (Ultra Dream Pluse); c) without any pretreatment. All prepared surfaces were bonded with Single Bond 2 and built up with resin composite (Filtek Z250). The micro-tensile bond test was performed. Fracture modes were evaluated by stereomicroscopy. Pretreated surfaces and bonded interfaces were characterized by scanning electron microscope (SEM). The data obtained was analyzed by two-way ANOVA (${\alpha}$=0.05). RESULTS. For both sound and eroded dentin, samples treated with desensitizer showed the greatest ${\mu}TBS$, followed by samples without any treatment. And samples treated with $CO_2$ laser showed the lowest ${\mu}TBS$. SEM study indicated that teeth with eroded dentin appeared prone to debonding, as demonstrated by existence of large gaps between adhesive layers and dentin. CONCLUSION. Pretreatment with Gluma increased the ${\mu}TBS$ of Single Bond 2 for eroded and sound teeth. $CO_2$ laser irradiation weakened bond performance for sound teeth but had no effect on eroded teeth.

• Steel and Composite Structures
• /
• v.19 no.6
• /
• pp.1549-1560
• /
• 2015

This paper presents the characterization of fatigue crack in the A283 Grade C steel using the MMM method by identifying the effects of magnetic flux leakage towards the crack growth rate, da/dN, and crack length. The previous and current research on the relation between MMM parameters and fatigue crack effect is still unclear and requires specific analysis to validate that. This method is considered to be a passive magnetic method among other Non-Destructive Testing (NDT) methods. The tension-tension fatigue test was conducted with a testing frequency of 10 Hz with 4 kN loaded, meanwhile the MMM response signals were captured using a MMM instrument. A correlation between the crack growth rate and magnetic flux leakage produces a sigmoid shape curve with a constant values which present the gradient, m value is in the ranges of 1.4357 to 4.0506, and the y-intercept, log C in the ranges of $4{\times}10^{-7}$ to 0.0303. Moreover, a linear relation was obtained between the crack length and magnetic flux leakage which present the R-Squared values is at 0.830 to 0.978. Therefore, MMM method has their own capability to investigate and characterize the fatigue crack effects as a main source of fracture mechanism for ferrous-based materials.

• Restorative Dentistry and Endodontics
• /
• v.28 no.4
• /
• pp.354-359
• /
• 2003

This study evaluated the effectiveness of the light emitting diode(LED) units for composite curing. To compare its effectiveness with conventional quartz tungsten halogen (QTH) light curing unit. the microhardness of 2mm composite. Z250, which had been light cured by the LEDs (Ultralume LED2, FreeLight, Developing product Dl) or QTH (XL 3000) were compared on the upper and lower surface. One way ANOVA with Tukey and Paired t-test was used at 95% levels of confidence. In addition. the amount of linear polymerization shrinkage was compared between composites which were light cured by QTH or LEDs using a custom-made linometer in 10s and 60s of light curing, and the amount of linear polymerization shrinkage was compared by one way ANOVA with Tukey. The amount of polymerization shrinkage at 10s was XL3000 > Ultralume 2. 40. 60 > FreeLight, D1 (P<0.05) The amount of polymerization shrinkage at 60s was XL3000 > Ultralume 2, 60> Ultralume 2.40 > FreeLight, D1 (P<0.05) The microhardness on the upper and lower surface was as follows ; (equation omitted) It was concluded that the LEDs produced lower polymerization shrinkage in 10s and 60s compared with QTH unit. In addition. the microhardness of samples which had been cured with LEDs was lower on the lower surfaces than the upper surfaces whereas there was no difference in QTH cured samples.

• Restorative Dentistry and Endodontics
• /
• v.40 no.4
• /
• pp.299-305
• /
• 2015

Objectives: The purpose of this study was to investigate the effectiveness of multiple decontamination procedures for salivary contamination after curing of a universal adhesive on dentin bond strength according to its etch modes. Materials and Methods: Forty-two extracted bovine incisors were trimmed by exposing the labial dentin surfaces and embedded in cylindrical molds. A universal adhesive (All-Bond Universal, Bisco) was used. The teeth were randomly divided into groups according to etch mode and decontamination procedure. The adhesive was applied according to the manufacturer's instructions for a given etch mode. With the exception of the control groups, the cured adhesive was contaminated with saliva for 20 sec. In the self-etch group, the teeth were divided into three groups: control, decontamination with rinsing and drying, and decontamination with rinsing, drying, and adhesive. In the etch-and-rinse group, the teeth were divided into four groups: control, decontamination with rinsing and drying, decontamination with rinsing, drying, and adhesive, and decontamination with rinsing, drying, re-etching, and reapplication of adhesive. A composite resin (Filtek Z350XT, 3M ESPE) was used for filling and was cured on the treated surfaces. Shear bond strength was measured, and failure modes were evaluated. The data were subjected to one-way analysis of variation and Tukey's HSD test. Results: The etch-and-rinse subgroup that was decontaminated by rinse, drying, re-etching, and reapplication of adhesive showed a significantly higher bond strength. Conclusions: When salivary contamination occurs after curing of the universal adhesive, additional etching improves the bond strength to dentin.