• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.3
• /
• pp.105-111
• /
• 2015

Ultrasonic machining (USM) does not involve heating or any electrochemical effects, and subsequently causes low surface damage, has small residual stress, and does not rely on the conductivity of the workpiece. These characteristics are suitable for the machining of brittle materials, such as glass or ceramics. However, USM for brittle materials generates cracks on the workpiece while machining, especially at the hole exit with a small diameter. In this study, wax coating was used to deposit wax on the back side of the workpiece to decrease the occurrence of cracks at the exit holes in USM, and it was finally removed with a cleaning process. The experimental results show that this technique is beneficial for restricting the occurrence of cracks in glass or ceramics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.946-949
• /
• 2001

Mirror surface finish of Si-wafers has been achieved by rotary in-feed machining with cup-type wheels in ELID grinding. But the diameter of the workpiece is limited with the diameter of the grinding wheel in the in-feed machining method. In this study, some grinding experiments by the rotary surface grinding machine with straight type wheels were conducted, by which the possible grinding area of the workpiece is independent of the diameter of the wheels. For the purpose of investigating the grinding characteristics of large scale diametral silicon wafer, grinding conditions such as rotation speed of grinding wheels and revolution of workpiece are varied, and grinding machine used in this experiment is rotary type surface grinding m/c equipped with an ELID unit. The surface ground using the SD8000 wheels showed that mirror like surface roughness can be attained near 2~6nm in Ra.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1105-1108
• /
• 2001

In these days, according s the increase of technological development the part demension goes up for ultra-precision. It is grinding behavior that is important processing which directly influences by machining accuracy at product quality with the net shape manufacturing. In this study, by using CBN wheel an analysis carried out for workpiece's profiles and its characteristics by measuring grinding force and surface roughness. Workpiece materials were used STD11, SUS304 and STB2 varing condition of feedrate and depth of cut.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.4
• /
• pp.111-117
• /
• 1998

In order to increase productivity of an assembly system composed of multiple robots along a conveyer line, an efficient sequence planning is necessary because the assembly time is dependent upon the assembly sequence. In this paper, a two-robot assembly system is considered in which two robots operate simultaneously and transfer parts from the part feeders to the workpiece on the conveyer one by one. In this case, the distance from the feeder to the workpiece varies with time because the workpiece moves at a constant speed on the conveyer. Hence, the sequence programming is not a trivial problem. Also, the two robots may interfere with each other kinematically and dynamically due to the simultaneous operation, so the sequence should be programmed to avoid the interferences. In this paper, the task sequence optimization problem is formulated and is solved by employing the simulated annealing which has been shown to be effective for solving large combinatorial optimizations.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.4
• /
• pp.126-136
• /
• 1991

In order to reduce the possibilities of personnel injuries and damages to machines and to obtaim higher efficiency and machining accuracy in the manufacturing system, the chucking technology has recentry become important. The chucking technology of work greatly affects both the grometrical accuracy and fonctional performance of the workpiece. In this study, the dynamic gripping force of a 3-jaw power chuck is investigated on the factors of the shape of jaw and the shape of workpiece. From this investigation, the following observations are obtained. 1) The higher stiffness of workpiece is, the higher decrease of dynamic gripping force is. 2) The nearer to the root of jaw is, the higher decrease of dynamic gripping force is. 3) The centrifugal force of affectting the decrease of dynamic gripping force has to be considered in the centrifugal force of affecting jaw.

• Journal of Mechanical Science and Technology
• /
• v.15 no.12
• /
• pp.1676-1682
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalts percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (WEDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary, Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rare as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without crack, 4 finish-cuts were necessary reducing fille electrical energy and the offset value.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.799-804
• /
• 1997

This paper is concerned with the heat flux distribution and energy partition for creep-feed grinding. Form measurements of transient grinding temperatures in the workpiece sub-surface using an embeded thermocouple, the overall energy partition to the workpiece was estimated form moving heat source theory for a triangular heat flux distribution as 3.0% for down grinding and 4.5% for up grinding. The higher energy partition for up grinding can be attributed to the need to satisfy thermal compatibility at the grinding zone. The influence of cooling outside the grinding zone can be analytically taken into account by specifying convective heat transfer coefficients on the workpiecs surface h /sab a/ heat source (grinding zone) and h /sab b/ behind the heat source. The smaller energy patition together with slightly lower grinding power favors down grinding over up grinding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.961-964
• /
• 1997

In this paper, grinding characteristics of ultra high speed cylindrical plunge grinding was investigated by use of vitrified CBN wheel. From the experimental result, it was convinced that grinding power is decreased according to the increase of wheel and workpiece speed due to changing of grinding mechanism which decreases depth of cut and length of contact curve according to increment of wheel speed. And also, stock removal reduction of each gram lead to improvement of surface roughness by increasing the wheel speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.367-372
• /
• 2003

This paper shows about the machine simulation embodiment when it happened NC equipment and between workpiece and interference collision at 5 axises processing of aircraft parts. And this research has been chosen because of the highest equipment interference occurrence rate at aircraft parts processing of 5 axises horizontal machine. It can verify simulation and machining process through correlation about their dynamic relations. interference, collision as embodied virtual manufacturing system of machining tool, workpiece, and holder etc. that is necessary element in shape of machine tool and function and processing in imagination ball. Also. it verified about interference and collision between NC equipment parts and workpiece, for applied machine simulation to NC Data of actuality aircraft parts of BULKHEAD and FRAME.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.203-208
• /
• 1998

Materials of the Frame hole in fishing trackle reel is made up a number large and small holes. Thus, it is difficult to effective machining. Abrasive flow machining(AFM) is useful to polish a internal or external surface of the 3-dimensional shape parts, which are used in many fields such as aerospace, automative, semi-conductor, and medical component industries. The machining process is that two hydraulic cylinders, which are located face to face, enforce abrasive media to the passage between workpiece and tooling parts alternately, and then the abrasives include in the media pass the passage and polish the surface of workpiece. The media which is made of polymer and abrasives plays the role of the tool for deburring or polishing complex shap workpiece by its viscoelastic characteristics. In this study, the abrasive media for abrasive flow machining was made by mixing viscielastic polymer with alunina and silicon carbide abrasive. Also, we present AFM device design and preliminary results of an investigation in to some aspects of the AFM process performance in fishing trackle reel.