• KSTLE International Journal
• /
• v.3 no.2
• /
• pp.114-118
• /
• 2002

In this work, head-disk interactions are studied when flying height becomes lower than laser bump height on the landing zone of a disk. With the reduction of the spinning speed in a spin stand, the flying height is decreased under the height of laser bumps. Conventional and padded pico sliders sweep between landing Bone and data zone and, then, the dynamic behavior of the pico sliders and head-disk impacts are investigated using AE and stiction/friction signals. After 200n cycle-sweep tests, bearing analysis and AFM analysis indicate that there are some signs of wear and plastic deformation in the landing zone of a disk, although AE and stiction/friction signals are not significantly changed during the sweep tests. The experimental results of this paper suggest that in CSS tests at component level, more rigorous examination methods of wear and plastic deformation might be necessary as flying height becomes getting lower.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.2
• /
• pp.21-26
• /
• 2005

From on the machining center cutting work of 5534, the characteristics such as spindle speed and feed speed fir the third point height, average spacing of roughness peaks, bearing ratio, center line average, ten point height. experiments is roughness for sampling length determine to measuring length of cutting feed speed 200, 400, 600, 800mm/min and spindle speed 800, 1000, 1200, 1400rpm. Third point height is spindle speed with most suitable cutting condition 1000rpm. Third point height is feed speed with most suitable cutting condition 400mm/min. Average spacing of roughness peaks are spindle speed with most suitable cutting condition feed speed increased to average spacing of roughness Peaks are increased. Spindle speed increased to average spacing of roughness peaks are decreased. Bearing ratio is spindle speed with feed speed increased to bearing ratio decreased. Center line average is spindle speed with most suitable cutting condition at 1200rpm feed speed with most suitable cutting condition at 200mm/min to cutting foe roughness suddenly decreased. Ten point height is spindle speed with most suitable cutting condition 1200rpm at ten point height cutting face roughness to decreased and feed speed with most suitable cutting condition 800mm/min at ten point height cutting face roughness to decreased.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.33-39
• /
• 2002

The purpose of this study is to evaluate the effects of continuing work on VDT(video display terminal). Therefore, we examined visual fatigue by a questionnaire and measured frequency of blinking, tear film break-up time(BUT), height of palpebral fissure, visual acuity, refraction with retinoscopy and accommodation before and after two hour long VDT work. For the ocular symptoms, the greatest number was tired eyes accounting for 34%. In the visual symptoms, blurred vision was the highest rate of 83% and in case of systemic symptoms, shoulder pain was 38% marked top ranking but other symptoms were also distributed similar rate. The frequency of blinking during VDT work decreased significantly comparing with the one at rest. The average frequency of blinking is 8/min during VDT work and 22/min at rest. The BUT measured immediately after VDT work decreased much more than in the resting state. The average BUT was 7sec immediately after VDT work and 12sec at rest. The height of palpebral fissure during VDT work increased significantly comparing with the value at rest. The average height of palpebral fissure was 7.69mm at rest and 9.04mm during VDT work. The average visual acuity decreased almost 9.5% from 0.63 to 0.57, but refraction with retinoscopy increased about 0.28D to the direction of myopic shift. The amplitude of accommodation decreased approximately 1.49D from 7.98D to 6.49D and this resulted from the prolongation of near point of accommodation. Near point of convergence also was prolongated from 9.45cm to 10.30cm after VDT work.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.3
• /
• pp.315-324
• /
• 2012

The purpose of current study was to investigate the effects of the heights on the lower extremities, torso and neck segments for energy dissipation during single-leg drop landing from different heights. Twenty eight young healthy male subjects(age: $23.21{\pm}1.66yr$, height: $176.03{\pm}4.22cm$, weight: $68.93{\pm}5.36kg$) were participated in this study. The subjects performed the single-leg drop landing from the various height(30, 45 & 60 cm). Force plates and motion-capture system were used to capture ground reaction force and kinematics data, respectively. The results were as follows. First, the ROM at the ankle, knee, hip and trunk was increased with the increased heights but the ROM at the neck was increased in the 60cm. Second, the angular velocity, moment and eccentric work at the ankle, knee, hip, trunk, and neck was increased with the increased heights. Third, the contribution to total work at the knee joint was not significantly different, while the ankle joint rate was decreased and hip and neck rate was increased in the 60cm, and trunk rate was increased with the increased heights. Lastly, the increase in landing height was able to augment the level of energy dissipation not only at the lower extremities but also at the trunk and neck. The findings showed that drop landing affect trunk and neck with lower extremity joints. Therefore, we need to consider that trunk and neck strengthening including stability should be added to reduce sports injury during prevention training.

• Asian Journal of Turfgrass Science
• /
• v.18 no.1
• /
• pp.37-46
• /
• 2004

The purpose of this study is to find the suitable putting green maintenance equipment for improving the quality of putting green. This study was carried out to investigate the green speed(i.e., ball roll distance) by different the types of greens mower(between work-behind greens mower and riding greens mower), the types of reel blades(between 9 blades and II blades) and the types of roller(between riding soil sprayer and lightweight roller). Green speed of golf course putting greens is assessed by use of Stimpmeter. The west course of Lakeside Country Club was selected for the case study. The results are summarized as follows; 1. The green speed was faster in 3.8 mm moving height treatment plot using work-behind greens mower than in 3.8 mm moving height treatment plot using riding greens mower right after the moving and even after eight hours had passed, and it was statistically significant at a 95% confidence level. Therefore, work-behind greens mower was judged to be a proper equipment type for the fast green management practice than riding greens mower. 2. The green speed was faster in 3.2 mm mowing height treatment plot using work-behind greens mower equipped with II blades than in 3.2 mm mowing height treatment plot using work-behind greens mower equipped with 9 blades, and this result was statistically significant at a 95% confidence level. Therefore, II-blade was judged to be a proper blade type for the fast green management practice than 9-blade. 3. The difference in green speed (green speed increased after rolling) between a treatment plot mowed at 3.0 mm mowing height with the work-behind greens mower and then rolled a single time with riding soil sprayer and a treatment plot mowed at 3.0 mm mowing height with the work-behind greens mower and then rolled once with lightweight roller was not statistically significant at a 95% confidence level. However, the difference in green speed (green speed decreased after rolling) between two treatment plots measured after eight hours had passed was statistically significant at a 95% confidence level. Therefore, the lightweight roller was judged to be a proper roller type for the fast green management practice than the riding soil sprayer.

• Journal of the Ergonomics Society of Korea
• /
• v.15 no.2
• /
• pp.51-62
• /
• 1996

This research utilized the psychophysical methodology, where secrw drivers are used, to determine the effects of i) the location and orientation of work objects, and ii) wearing gloves, on ratings of perceived exertion at various body parts. The validity of the psychophysical methodology in determining a preferred work pace was also studied. The subjects drove screws with a screw driver into thick wooden sheet at three vertical and three horizontal locations. They drove serews for 3 minutes at each location and assessed the condition using the psychophysical scale. The results showed that only the vertical location was a significant factor in determining the discomfort ratings. Driving screws at elbow height on the vertical surface and with the lower arm close to the body on the horizontal surface were the work locations with the smallest ratings of perceived discomfort. Wearing gloves had significant effects on reducing the pain of the hand. From the experiment in which a comfortable work pace was identified using 20 minute psychophysical adjustment, it was found that the psychophysical method is sensitive to workers perception of the physical stress when the upper limbs are employed. This was confirmend by the high correlation between the psychophysical results and EMG measurement.

• Journal of the Korean Society of Safety
• /
• v.16 no.2
• /
• pp.80-84
• /
• 2001

Work stress and health are very important factors related to workers' condition and work safety, Author has conducted a couple of tests to check up three people's pulses before they work during their work for three types of safety guard in construction site. Work type, age, weight, sex experience year, ambient temperature n recorded as variables in this study. These are checked and asked by the author directly, before their pulse check Also, workers' Pulses were measured at height H-0 and H-9.0m to understand psychological the degree of psychological nervousness degree. POLAR protrainer NVTM HRM system(wrist recorder and sensor) was used for the site test. There are three(3) different types of construction safety guard which have been used for, this study. They are usually or frequently used and found in the site. Four different ranges of age groups(20's, 30's 40's, 50's) carpenters are assisted to the test sites with wearing pulse recorder and sensor respectively. All three types of safety guards have the same height 90㎝ even though they are different types. On top of five(5) stories tublar framed scaffolding is fabricated, similar to the one in site, where those safety guards are installed. The older(=more experienced) the workers are the more stable they are. it is shown. Also, It is verified the visually uncomfortable rail type can cause workers to psychologically be unstable.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.11 no.2 s.24
• /
• pp.13-21
• /
• 1987

Nowadays, the amount used carpets are on the increase, according to the improvement of life-style. The pleasantness of carpet is caused by the properties of pile, because the most carpets are made pile fabric. For that reason, a study on the compressional properties of carpet is very important issue. This study has been carried out to investigate the differences of compressional properties in various acrylic carpets which were Cut, Tufted, Jacquard and Shag. Each acrylic carpets was transformed to 4, 6, 8 mm of pile height, as results of transformation, we could get the pressure-thickness curve and pressure-deformation curve. The results are summarized as follows. 1. Rate of compression increases, compressive resistance and compressive elasticity decr-eases, as pile height increases. 2. Regardless of pile height, compressive elasticity reached the limit in recovery period at about 10 minutes. 3. Work of compression increases, as pile height increases. 4. Work of compression decreases, as apparent density increases. 5, Cut-type carpet has the best cushion.

• Plant Journal
• /
• v.4 no.2
• /
• pp.66-72
• /
• 2008

In this inquiry, I would suggest jet ventilation system for effective elimination of welding flaw at machinery material welding shop on plant and evaluate the airstream on inner space and property of welding flaw's density through the examination. We can know outer atmosphere inflows at the speed of about 0.05m/s from western entrance in case of stopping the jet ventilation system, but airstream is accumulated on entire space. At height of worker's breathing surface(Ground Level = 1.5 m, below of GL) and welding work center, density of welding flaw on upper part(GL = 12m) is appeared 4 times higher than outer atmosphere at surplus range besides nearby of western entrance. At operation of jet ventilation system, since the smooth air current transfer at inner space and exhaust effect the wind speed is maintained at 0.932 m/s at the point of height of worker's breathing surface on inner space and it's concluded about the working conditions have been better than before operation of jet ventilation system because of that results show that inner space density of welding flaw at height of worker's breathing surface is 40.5%, and in the work shop, it is 20.3% at upper part.

• Journal of International Academy of Physical Therapy Research
• /
• v.3 no.2
• /
• pp.469-474
• /
• 2012

The purpose of this study is to analyze the correlation between the stature and the muscle performance ratings and the subjective discomfort rations at performing lower arm's pronation and supination according to change sin the height of working table for more efficient performance at designing a working table and performing a work. For the purpose, this study conducted an experiment targeting 40 people in their 20s, who were classified into 4 groups each group composing 10 people at intervals of 5cm from the standard stature of 166.5cm. The experiment measured the maximum isometric pronation and the supination muscular power, and at measuring the factors, the heights of working tables were set as 800mm, 850mm, and 900mm. From the measurement results, it was found that the stature and the maximum muscular power was correlated. That is, as the experiment groups's average stature is higher, the maximum muscular power was higher. For the correlation between the motion patterns(pronation and supination) and the maximum muscular power, it was seen that the maximum muscular power was higher at performing the pronation than the supination. In the correlation between motion patterns and the subjective discomfort ratings, it was seen that the subjective discomfort rating was higher at performing the supination than the pronation. For the correlation between height adjustment and the subjective discomfort ratings, as the height of working table was lower, the subject discomfort rating was lower. Therefore there was no difference in the maximum muscular power according to the height changes of working table, but it was found that as the working table was higher, the user felt more comfortable.