• Current Research on Agriculture and Life Sciences
• /
• 제27권
• /
• pp.29-33
• /
• 2009

Liquefied-wood polymer composite was prepared and mechanical properties was evaluated to develop potential utility of liquefied wood. The liquefied wood was made from waste wood and chemical modified with acetic anhydride and maleic anhydride (MA), phtalic anhydride (PA). The composite sheet was prepared from modified liquefied-wood and polymer(PE). The mechanical, chemical and microscopical properties composite sheet were investigated. The results were summarized as follows, 1. The tensile strength was increased and breaking elongation of composite sheet was decreased with the time of acetylation and the dosage of MA. 2. The Young's modulus of composite sheet was gradually decreased with the dosage of PA. 3. The peak intensity of 1737cm-1 in FT-IR spectra of chemical modified liquefied woods was increased. 4. The dispersity of liquefied woods with PE was improved with chemical modification.

• 한국농공학회지
• /
• 제32권3호
• /
• pp.79-86
• /
• 1990

Based on limited number of tests on reinforced wood beams using polymer mortar in this study, following conclusions were drawn ; 1.Reinforcing compression side of wood beam using polymer mortar was effective in reducing deflection. 2.By increasing thickness of polymer mortar, effective beam stiffness was improved, but energy absorption was reduced. 3.Polymer mortar reinforcement improved compressive strength and reduced strain in compression side of the beam. Therefore, it was possible to change the failure mode from by compression in control beam to by tension in composite beams. 4.The composite beams that have more than 2cm of polymer mortar layer did not perform well because a strain redistribution and separation of meterials at interface were induced in moment span. 5.To maximize the load carrying capacity of composite beam, it is necessary to make polymer mortar and wood behave together without failing at interface. To do this, it is needed to use a polymer mortar which has high strength with such elastic modulus that is closer to elastic modulus of wood. otherwise, it is recommended to use shear connectors at interface to prevent separation of materials under ultimate load.

• 한국가구학회지
• /
• 제18권4호
• /
• pp.268-274
• /
• 2007

Environmentally-friendly polymer composite films were manufactured from cellulose acetate (CA) and polyethylene (PE). To investigate the optimum manufacturing conditions for the composite, various tests such as thermal analysis, surface observation, IR spectra analysis, and elongation ratio of polymer composite films were carried out. The mixing ratio of each element and manufacture condition was found to be very important for the best goods.

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.59-67
• /
• 2001

Rice husk flours were analyzed by chemical composition and thermogravimetric methods in nitrogen atmosphere to discuss its feasibility as a raw material for manufacturing agricultural lignocellulosic fiber-thermoplastic polymer composite. It was revealed in the chemical composition analysis that rice husk flour was composed of moisture, 5.0%; lignin, 21.6%; holocellulose, 60.8%; ash, 12.6%. In the thermogravimetric analysis (TGA), thermal decomposition behavior of rice husk flour from room temperature to $350^{\circ}C$ was similar to that of wood flour, but rice husk flour was more thermally stable from 350 to $800^{\circ}C$ than wood flour because of higher silica content in the rice husk flour and smaller particle size of rice husk flour. The activation energy of thermal decomposition was evaluated using Flynn & Wall expression. As the thermal decomposition proceeded in rice husk flour, the activation energy of thermal decomposition appeared almost constant up to ${\alpha}=0.25$, but thereafter increased. Activation energy of thermal decomposition in wood flour, however, decreased steeply up to ${\alpha}=0.3$, but thereafter remained almost constant. From the results, rice husk flour was thought be a substitute for wood flour in manufacturing agricultural lignocellulosic fiber-thermoplastic polymer composite in the aspect of thermal decomposition.

• Elastomers and Composites
• /
• 제46권3호
• /
• pp.211-217
• /
• 2011

Wood Polymer Composite(WPC)는 우수한 물성 및 가공성과 더불어 자원재활용 및 벌목규제 대응 등의 환경적인 측면에서 각광을 받고 있는 재료이다. 본 연구에서는 이축스크류식 치합형 압출기를 이용하여 상용화 WPC를 제조하였다. WPC의 물성에 영향을 미치는 세 가지 주요 실험 변수 즉 목분의 함량, coupling agent의 함량 그리고 목분의 전처리 영향을 자세히 관찰하였다. 목분의 함량에 따른 WPC의 물성변화는 목분함량이 증가함에 따라 인장강도 와 열안정성이 감소하고, 수분흡수성이 증가하는 것이 관찰되었다. PP-g-MA 첨가 시 기계적 물성은 향상되고, 수분흡수성이 감소하는 것이 관찰되었다. 목분을 전처리하여 제조한 시편에서는 가장 높은 인장강도의 향상을 나타냈지만, 셀룰로스의 결정구조 변화로 수분흡수성이 증가하는 것이 확인되었다.

• 폴리머
• /
• 제38권3호
• /
• pp.327-332
• /
• 2014

고분자/목분 복합재료는 경제적이고 친환경적이기 때문에 최근 많은 관심을 끌고 있다. 본 연구에서는 목분의 크기가 폴리프로필렌/목분 복합재료의 열적, 기계적 특성에 미치는 영향을 조사하였다. 용융혼합 및 압축성형에 의해 제조된 복합재료 샘플의 기계적 특성을 조사하기 위해 만능재료시험기와 아이조드 충격시험기를 사용하였고, 열적 특성을 조사하기 위해 TGA, DMA, DSC 및 TMA를 사용하였다. 말레산 무수물로 개질된 폴리프로필렌 커플링 제 3종을 테스트하여 최적의 커플링제를 선정하였으며 동일조건 하에서 목분의 크기가 복합재료의 물성에 미치는 영향을 살펴보았다. 600, 250, 180, $150{\mu}m$의 네 가지 목분 크기에 대해 실험한 결과 목분의 크기가 작을수록 복합재료의 굴곡강도, 굴곡탄성률, 결정화도 및 내수성이 증가하였다.

• Elastomers and Composites
• /
• 제48권3호
• /
• pp.216-220
• /
• 2013

본 연구에서는 목분-고분자 복합체(Wood Flour-Polymer Composite, WPC)의 상분리 특성을 조사하고 이를 토대로 목분함량에 따른 WPC의 기계적 물성 변화에 관한 원인을 규명하였다. 이를 위해 고분자 매트릭스로 폴리프로필렌을 사용하여 서로 다른 함량의 목분을 갖는 시편을 제조하였다. 서로 다른 목분 함량을 갖는 시편들의 DSC thermogram으로부터 목분 함량에 따른 고분자 PP의 결정화 경향과 $T_m$ 경향을 분석하였다. 목분 함량이 증가함에 따라 고분자 PP의 결정량 및 $T_m$값 모두 감소하다 다시 증가하는 결과를 나타내었다. 이로부터 낮은 목분 함량에서는 목분이 매트릭스인 고분자 내에 분산되어 있으나 일정 목분 함량이상에서는 WPC의 매트릭스인 PP와 목분사이에 상분리가 일어남을 확인할 수 있었다. 한편, WPC 시편의 인장강도는 목분 함량이 증가할수록 감소하는 결과를 나타내었다. 낮은 목분 함량에서는 고분자에 분산된 목분과 고분자 사이에서의 낮은 계면 결합력과 시편내에서 강도를 높이는 역할을 하는 결정량의 감소가, 높은 목분 함량에서는 PP와 목분사이에서의 상분리로 인한 계면 결함이 WPC 시편의 인장강도를 목분함량 증가에 따라 지속적으로 감소시키는 원인이 되는 것으로 파악되었다. WPC 시편의 충격강도는 목분 함량이 증가함에 따라 증가하다가 목분 함량이 20%인 경우 최고값을 나타내며, 그 이후 다시 감소하는 경향을 나타내었는데, 낮은 목분 함량에서는 목분 함량이 증가할수록 시편의 결정량이 감소하므로 시편의 취성 감소에 의해 충격강도가 향상되나, 높은 목분 함량에서는 고분자 매트릭스와 목분 사이의 상분리로 인해 다시 충격강도가 저하되기 때문인 것으로 판단된다.

• Journal of the Korean Wood Science and Technology
• /
• 제1권2호
• /
• pp.21-39
• /
• 1973

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.91-94
• /
• 2005

Polypropylene as a matrix has been used for wood polymer composites(WPC). In preparing WPC, the coupling agent, Polypropylene grafted Maleic Anhydride(PP-G-MA) was used in order to obtain a good interfacial bonding force between matrix and fillers and dispersion of wood powders. In this study, the effects of wood powder contents and water absorption on the mechanical properties were experimentally investigated. The tensile strength and flexural strength of composites reached its peak value when the wood powder content was around 60 wt%. However, the peak value of the impact was observed about 30 wt% of wood powder content. The tensile strength and flexural strength increase with increasing the wood power contents. But the impact strength decrease with increasing the wood powder contents. The slight change was observed with the water absorption in the WPC. The optimal condition of the compositions such as Anti-oxidant and UV stabilizers for the outdoor application was suggested in this research.

• Journal of the Korean Wood Science and Technology
• /
• 제21권2호
• /
• pp.31-37
• /
• 1993

Composites of styrene polymers with woody fibers were prepared, and the effect of compatibilizers on their mechanical properties was evaluated. To improve the compatibility of wood fibers and the matrix polymers, styrene-maleic anhydride copolymer(SMA) and maleic anhydride-modified polymers were used as compatibilizers. As results, maleic anhydride-modified polystyrene and SMA were proved to improve the tensile strength of the molded composites, and also were evaluated as good compatibilizers for the wood fiber polystyrene composite. Cellulosic fiber (dissolving pulp) provided better reinforcement than lignocellulosic fiber(thermomechanical pulp). On the contrary in the case of the composite of wood fiber and acrylonitrile-butadiene styrene copolymer(ABS), SMA and maleic anhydride-modified acrylonitrile-butadiene-styrene copolymer(MABS) did not act as compatibilizers. However, MABS was evaluated as a good polymer matrix to make wood fiber reinforced composite. The tensile properties of the composites of wood fiber and MABS were superior than those of wood fiber-ABS composites.