• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.5 s.108
• /
• pp.21-28
• /
• 2004

Com stalk was evaluated to verify the potential as a raw material for papermaking. The lower lignin content and higher hemicelluloses content of cornstalk than any woods were considered to be beneficial for pulping and strength properties of paper. The average fiber length of com stalk was similar to those of hardwood, but longer fiber fraction is little bit included. It was found that the refining of pulp can be eliminated because of higher hemicelluloses content and narrower fiber characteristic. Disadvantages of cornstalk pulp were lower bulk and opacity, but it can be overcome by the proper use of wood pulp and filler.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.1
• /
• pp.67-74
• /
• 2004

This study was carried out to investigate the characteristics of handsheets made from nonwoody New-Zealand hemp (Phormium tenax) fibers that was not used before in Korea. The results were as follows : 1. Physical properties of bleached phormium fiber were satisfactory for handsheet forming. Specially, tensile strength was improved by adding bleached phormium fiber. 2. Opacity of handsheet with phormium pulp was fine, therefore it can be useful fiber to improve opacity of light-weight printing paper. 3. Filler retention rate was improved when phormium pulp was added, while drainage time was increased. 4. Phormium fiber has good characteristics as pulp for paper manufacture. So it can be valuable non-wood fiber resource if drainage problem is solved.

• Journal of the Korean Society of Tobacco Science
• /
• v.22 no.2
• /
• pp.164-169
• /
• 2000

The reconstituted tobacco leaves(RTL) playa major part in the control of the low density and tar cigarette. Reconstituted tobacco manufactured by the papermaking process has much higher filling power than homogenized tobacco manufactured by slurry and rolling process. Fragile reconstituted tobaccos are liable to lead to small particles detrimental for filling power so they must be properly flexible. This work was conducted to determine the effect of CaCO$_3$ addition in paper-making process on the filling power and the flexibility of the reconstituted tobacco and to obtain the fundamental informations for improving the quality of domestic reconstituted tobacco. We analyzed the wood fiber species, the filler level, the fiber length, the fineness level and observed the surface of the RTL. From the obtained results, we could determine that foreign reconstituted tobacco was manufactured by blending softwood with hardwood and over 8% of calcium carbonate at the addition level. The domestic RTL has much higher fine fiber level by 23.2 % than that of foreign, so the refining treatment process and the condition must be reoptimized for the improvement of RTL quality.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.271-278
• /
• 2006

We used polymers of alternating cationic and anionic nature to build up shells on fiber surfaces, strengthen the worn-out fibers and improve paper properties made from such fibers. OCC and ONP pulps were either dipped or salted out in the cationic polyallylamine, polyacrylamide and starch solutions. After centrifugal drying, these were followed by treatments in anionic polyacrylic acid, poly-acrylamide, and starch solutions, respectively. The shell-enhanced fibers were formed into handsheets and their physical properties evaluated. The results show that building multiple shells on worn-out fiber surfaces can strengthen the fibers and paper. The simpler and more practical impregnation-centrifuging treatment provided the desired effects, whereas salting out the polymers produced somewhat superior fibers. The latter process, were impractical, however. The first pair of polymeric shells imparted marked strength improvement, whereas later layers had diminishing efficacies. Overall, the methods can improve fiber quality, attaining paper strength requirements without resorting to expensive measures. Alternate cationic polymer and filler powders were also deposited on fiber surface based on the micriparticle system in an anticipation of stiffness gains. Platy minerals, such as montmorillonite, bentonite, sericite, clay and talc were added following cationic PAM. After dewatering of polymer-pigment shelled fiber of one to 3 pairs of layers, handsheets either calendered or uncalendered were evaluated. The results indicate that regardless of calendaring, stiffness of the handsheets did not improve appreciably while certain other strength properties showed gains. We also attempted the novel starch gel filler addition method wherein tapioca starch and filers (PCC, sericite or clay) were mixed at high solids content of 50% and cooked until gelatinized. The filled handsheets were dried under various conditions and then tested for their properties. Improvements in strengths of modified filled paper were observed.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.51-62
• /
• 1999

The objective of this research is to develop paper sludge reinforced thermoplastic composites which incorporate the advantages of each component materials. The effects of paper sludge content(0, 10, 20, 30, 40----), mesh size(20~40, 60~80, less than 100mesh), and coupling agent(Epolene E-43 and Epolene G-3003) on the mechanical properties of paper sludge-polypropylene composites were investigated. Composite density increased with an increase in the paper sludge content. When paper sludge is incorporated into a polypropylene matrix, the flexural properties of the composite increase significantly with an increase in the paper sludge mixing ratio. Especially, flexural modulus was improved with increasing paper sludge content. The flexural strength of composites was improved, but flexural modulus reduced somewhat with decreasing paper sludge particle size. The flexural properties of paper sludge-polypropylene composites were improved by using coupling agents to enhance the bonding between reinforcing filler and matrix. Use of the epolene E-43 and G-3003 resulted in considerable improvement in the flexural strength over control specimens. The flexural strength of the G-3003 composite system is higher than that of the E-43 system. Generally, izod notched impact strength of paper sludge-polypropylene composite decreased slightly, whereas izod unnotched impact strength decreased significantly with increasing paper sludge contents. There was no effects of paper sludge particle size on impact strength of paper sludge-polypropylene composites. And izod unnotched impact strength of epolene E-43 composite system sharply decreased but that of G-3003 composite system was no tendency with increasing additive content.

• Journal of Conservation Science
• /
• v.31 no.2
• /
• pp.125-130
• /
• 2015

Specific techniques and materials in conservation of traditional lacquer has not been transmitted. This study aims to compare the basic characteristics of the filler which used in the base layer of lacquer conservation. Tohoe(a mixture of lacquer and Clay) and the three kinds of additives which is mixed with Tohoe and Goksu(a mixture of lacquer, wood powder and rice starch) are estimated in drying rate, impact resistance, abrasion. Among those samples, the more amount of clay causes fast dryness speed and worse cracks on the surface. The impact resistance is weakened at high amount of clay. There is no significant differences of impact resistance between both additives that is mixed with the samples and additives. The samples that are mixed with Goksu and additives show high impact resistance. In the polishing test, the more amount of filling powders show higher grinding degree and the sample that are mixed with wood powder and charcoal show higher degree as well. The highest grinding degree is Maekchil and Goksu but the lowest one is the sample of the rooftile powder mixture.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.1 s.129
• /
• pp.29-37
• /
• 2005

The main objective of this research was conducted to evaluate the impacts on the thermoplastic polymer which is a matrix polymer and the rice husk flour (RHF) which is a reinforcing filler relative to the manufacturing temperature and time when bio-composites were manufactured. In order to evaluate the impacts on the rice husk flour relative to the manufacturing temperature, the rice husk flour was persevered for 10 minutes to 2 hours period at $220^{\circ}C$ temperature which was then added with the polypropylene (PP) and low-density polyethylene (LDPE) to complete the manufacturing process of the bio-composites and measure the corresponding mechanical properties. As preserving time increased at $220^{\circ}C$, the tensile and impact strength were decreased due to the thermal degradation of the main components within the rice husk flour. The thermogravimetric analysis (TGA) was used to measure weight loss caused by the actual manufacturing temperature and the result was that the thermoplastic polymer had not scarcely occurred weight change, but there had been increasing rate of weight loss relative to time for the rice husk flour and the bio-composites under the consistent temperature of $220^{\circ}C$ for 2 hour time period. Therefore, the proper manufacturing temperature and time settings are significantly important features in order to prevent the reduction of mechanical properties which were induced throughout the manufacturing process under the high manufacturing temperature.

• Journal of Adhesion and Interface
• /
• v.13 no.4
• /
• pp.171-181
• /
• 2012

The demand characteristics of the conventional 12 kinds of epoxy resins which have been used for restoration of the ceramic relics were investigated to provide standards of the effective materials in this study. The result of durability analysis showed that a liquid type is more effective in ceramic relics (low damage, high strength), and a paste type is more effective in earthenware relics (high damage, low strength). The result of workability analysis appears that the liquid type is higher than the paste type, and a slow curing type is higher than a fast curing type in surface hardness. Therefore, in the case of the liquid type which is hard to reprocess due to high surface hardness, it is necessary to conduct a study on improving physical properties by adding filler. The result of the gloss analysis on epoxy resins showed that the liquid type (colorless) has higher gloss than the paste type, and the slow curing type has higher gloss than the fast curing type in liquid types. CDK-520A/520B and Araldite SV 427-2/HV 427-1 showed the most similar gloss to $700^{\circ}C$ earthenware, Devcon 5 minute, EPO-TEK 301-2, and Quik Wood showed the most similar gloss to celadon and whiteware, Quik Wood, EPO-TEK 301-2, and Devcon 5 minute showed the most similar gloss to buncheongware. It is necessary for conservator to decide the range of the restoration surface by predicting the increase and decrease of the restoration surface because most of the epoxy resins caused the volume change in curing process.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.2
• /
• pp.33-40
• /
• 2013

Powdered additive or organic filler is used to improve paperboard thickness and to reduce drying energy consumption in the Korean paperboard industry. In a previous study, we identified alternative non-lignocellulosic resources to wood powder, specifically brewers grain and oil palm frond powders, and verified that these materials had the same functionality as wood powder. The main drawback of the use of such additives, including both lignocellulosic and non-lignocellulosic resources, is the deterioration in paperboard strengths. Therefore, we carried out a basic study on the surface modification of brewers grain and oil palm frond powders to improve the strengths of paperboard. Surface modification was performed using various types of cationic and oxidized starches. The streaming current and zeta-potential of the two non-lignocellulosic powders were measured and CLSM images were taken to assess the surface modification.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.100-107
• /
• 2007

People have spent lots of time inside building about 90% of these day. Industry has been developed rapidly after I960. Construction materials had changed from natural materials to chemical materials and confidentiality of building has been more higher than before by policy of saving energy. These have caused sick-building syndrome (SBS) for us. So people want environmental construction materials for their house. We designed a environmental loess (yellow soil) finishing material which was composed of loess, water, water-soluble resin, hardener and filler. The purposes of this study were that making an environmental loess finishing material with optimum ratio, evaluating the usability of loess finishing material for wall. Furthermore it was suitable for wall to evaluate mechanical properties that are impact test, cracking test, abrasion test and de-bonding test, environmental properties that were emission of VOCs, formaldehyde and far infrared radiation.