• Composites Research
• /
• 제29권5호
• /
• pp.276-281
• /
• 2016

본 연구에서는 돌침대용 석재/목재 복합재의 열적특성 및 접착특성 개선에 대한 연구를 진행하였다. 기초 물성을 체크하기 위해 인장실험을 진행하였고 석재 및 목재의 실시간 온도측정을 진행하였다. 석재/목재 복합재의 가열부위에 따른 열적 특성을 알아보기 위해 석재를 위로 두었을 때와 목재를 위로 두었을 때 두 가지 방법으로 가열을 실시하였다. 에폭시 접착제에 CNT를 넣음으로써, 열적 및 접착특성의 변화를 알아보기 위하여 실시간 온도측정과 랩 전단 실험을 실시하였다. 실험결과 목재를 위로 두었을 때 열적 특성이 좋은 것을 확인하였고 에폭시 접착제에 CNT를 넣음으로써 접착특성 및 열적특성이 개선됨을 볼 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권2호
• /
• pp.42-45
• /
• 1996

A residue from the newsprint waste was investigated as a filler in adhesive for bonding southern pine plywood. The residue was prepared by drying the wet residue to 8% moisture content and grinding the dry material using a laboratory Wiley mitt with a 75-${\mu}m$(200-mesh) screen. The residue was compared to a commercial filler commonly used in structural plywood adhesives. A total of 48 three-ply panels. 12.7mm nominal thickness and 0.3 by 0.3 m in size, were fabricated at two press times(4 and 5 min) and three assembly times(20, 40 and 60 min). Evaluations of the residue were carried out by performance tension shear tests after two 4-hour boil accelerated aging tests on plywood. The test results included tension shear strength and estimated wood failure values. All plywood made with the residue filler were comparable to the control-bonded plywood. These results indicate that residue from the newsprint waste streams would be suitable as filler for plywood adhesives.

• 접착 및 계면
• /
• 제16권2호
• /
• pp.69-75
• /
• 2015

돌침대에 사용되는 석재의 무게를 줄여 경량화를 추구하려면 석재의 두께를 줄이고 보강재료로 석재의 강도를 유지해야 한다. 본 연구에서는 돌침대용 석재/목재 보드 개발에 대한 연구를 진행하였다. 돌침대에 삽입될 돌의 무게를 줄이기 위해 석재와 목재를 접합하였다. 목재의 강도 향상과 표면개질을 위하여 열처리 조건에 따른 목재의 물성변화를 관찰하였다. 대기 조건에서 열처리한 목재의 경우 고온의 온도에 따라 목재의 강성이 높아졌다. 열처리 최적조건은 표면에너지와 인장, 굴곡 강도변화 경향을 바탕으로 $100^{\circ}C$ 조건임을 확인하였다. 석재와 목재간 높은 접착력을 확보하기 위해 최적의 접착제 조성을 연구하였다. 아민계 에폭시 접착제, 폴리우레탄(PU)계 접착제, 염화고무계(CR) 접착제 마지막으로 염화비닐초산계 접착제에 따른 석재와 목재간 랩 전단실험을 진행하였다. 랩 전단 실험 후 파단면을 관찰해볼 때 에폭시 접착제를 이용할 때 목재 기지의 인열 파괴가 발생되었다. 접착면에서의 전단력이 목재 자체의 파괴 강도보다 높다는 결과를 바탕으로 최적의 접착제 조건이 에폭시계 접착제임을 확인할 수 있었다.

• 한국산림과학회지
• /
• 제60권1호
• /
• pp.37-44
• /
• 1983

요소수지(尿素樹脂)의 변성제(變性劑)로서 열가망성(熱可望性)의 아세톤수지(樹脂)를 첨가(添加)하고 합판(合板)의 접착력(接着力) 및 목파율(木破率)에 미치는 영향(影響)을 조사(調査)하였다. 결론(結論)을 요약(要約)하면 다음과 같다. 1) 합판(合板)의 접착력(接着力)과 목파율(木破率)은 열판온도(熱板溫度) $120^{\circ}C$에서 제조한 것이 가장 좋은 값을 보였으나 아세톤수지(樹脂)의 혼합비율(混合比率)이 증가(增加)함에 따라서 그 값은 점차 감소(減少)되었다. 2) 아세톤수지(樹脂)의 몰비율(比率)은 합판(合板)의 접착력(接着力) 및 목파율(木破率)에 영향(影響)을 미치지 않았다. 3) 아세톤수지(樹脂)를 혼용(混用)한 합판(合板)은 요소수지(尿素樹脂)만으로 접착(接着)된 합판(合板)의 접착력(接着力) 및 목파율(木破率)을 능가하지 못했다. 따라서 아세톤수지(樹脂)는 요소수지(尿素樹脂)의 변성제(變性劑)는 부적당(不適當)하였다.

• 한국응용과학기술학회지
• /
• 제30권3호
• /
• pp.551-559
• /
• 2013

To investigate the adhesion effect of sodium bisulfite content in making blocked isocyanate, wood adhesive PB-1, PB-2, PB-3 and PB-4 containing sodium bisulfite content of 15%, 22.5%, 30% and 37.5% were synthesized respectively. As a result, when the amount of sodium bisulfite increased in adhesives, the tensile strength was found to be proportionally increased. The final adhesive mixtures were manufactured using a two-components system which are prepared by mixing two separate protein and BI solutions due to the precipitate in the adhesives. As PVA was added to adhesives to increase tenacity, the plywood dehiscence phenomenon after cold pressing process was declined. By addition of PVA, the tensile strength was improved up to $6.5{\sim}7kgf/cm^2$ with BI/protein ratio from 1:6 up to 1:8. Phase separation between milk fat and aqueous layer was disappeared after addition of emulsifier, Tween 20. Additon of Tween 20 showed tensile strength up to $5{\sim}6.5 kgf/cm^2$ at NCO/protein ratio of 1:12 ~ 1:14 without phase separation.

• Journal of the Korean Wood Science and Technology
• /
• 제51권2호
• /
• pp.81-97
• /
• 2023

The aim of this study were to evaluate tannin resorcinol formaldehyde (TRF) for the preparation of cross-laminated timbers (CLTs) made from fast-growing tree species and to analyze the physical and mechanical properties of CLTs. TRF copolymer resin was prepared by using the bark extracts of Swietenia mahagoni (L.) Jacq. It was observed that the TRF adhesive possessed less solid content (23.59%), high viscosity (11.35 poise), and high pH values (10.0) compared to the standard phenol resorcinol formaldehyde. The TRF adhesive was applied to produce CLTs with the addition of 15% tapioca and flour as an extender. The six-layered CLTs were produced from sengon (Falcataria moluccana Miq.), jabon [Anthocephalus cadamba (Roxb) Miq.], coconut (Cocos nucifera L.), and the combination of coconut-jabon and coconut-sengon wood. The analysis of variance revealed that the layer composition of CLT significantly affected the physical and mechanical properties of the beam. While the modulus of rupture met the standard, the moisture content and modulus of elasticity values did not fulfill JAS 1152-2007. All of the CLTs produced in this study demonstrated low formaldehyde emission, ranging from 0.001 mg/L to 0.003 mg/L, thereby satisfying the JAS 1152 for structural glue laminated timber.

• Journal of the Korean Wood Science and Technology
• /
• 제12권1호
• /
• pp.38-43
• /
• 1984

Water soluble urea-melamine-phenol copolymer adhesive manufactured with 80 percent of urea resin contents was manufactured by different molar ratio for a high temperature curing type, and their properties and strengthes were examined through manufactures of plywood with Kapur (Dryobalanops spp.) veneers. The results are summarized as follows: 1. Specific gravities of air dried plywood manufactured from each adhesive ranged from 0.78 to 0.84 and their moisture contents met the KS requirement. 2. In dry and wet shear strength, $U_{80}M_{10}P_{10}$ copolymer resin showed the highest value and urea resin was the lowest, indicating that melamine and phenol were effective for increasing glue shear strength of urea resin. 3. In case of glue shear strength after boiling test, phenolic resin was the nest and melamine was not so effective as phenol on reinforcement of boiling water resistance of urea resin.

• Journal of the Korean Wood Science and Technology
• /
• 제24권3호
• /
• pp.45-50
• /
• 1996

Wood chips of oak(Quercus mongolica) and larch(Larix leptolepis) were treated with low pressure steaming explosion. Main components of exploded wood were separated with hot water and methanol extraction. Crude lignin separated from those extractives were purified and those chemical characteristics were investigated. And also, lignin adhesive was prepared from crude lignin and studied those chemical characteristics. The results can be summarized as follows ; 1. The purified lignin by Bj$\ddot{o}$kman's method from crude lignin is about 30% in exploded oak wood and is about 11% in exploded larch wood as a low amount. 2. The phenolic hydroxyl groups in the purified lignins are little higher than those of MWL and molecular weight distributions of the purified lignins are some lower than that of MWL. 3. Alkaline nitrobenzene oxidation products are very low in the clude lignin but those are increased in the purified lignin 4. The gravity of lignin resins(1.15 and 1.13) are a little lower than that of phenol resin(1.16) and the compressive shearing strength of lignin resins are higher than those of phenol resin.

• Journal of the Korean Wood Science and Technology
• /
• 제51권1호
• /
• pp.14-22
• /
• 2023

Economical use of larix (larch) boards (grade 3) in industries is lower than that of imported hardwood; thus, studies have been conducted toward performance improvement of larix boards. Herein, flexural modulus of larix board samples laminated with wood adhesives polyurethane resins, poly (vinyl acetate) resins, phenol-resorcinol-formaldehyde resins, melamine-formaldehyde resins, and urea-formaldehyde resins was compared with that of the samples bonded with adhesives reinforced with mesh-type basalt fibers. Moreover, the flexural moduli of the laminated samples bonded by mesh-type basalt fibers were compared with those of reinforced samples. The results showed that boards laminated with polyurethane and urea-formaldehyde resin adhesives had higher flexural modulus than those without the lamination. In particular, the increase in the flexural modulus was relatively significant for the 2- and 3-ply board structures laminated with polyurethane adhesives compared to those with reinforcement. The 3-ply board structure without reinforcement had the highest flexural modulus when the urea-formaldehyde resin adhesive was used.

• Journal of the Korean Wood Science and Technology
• /
• 제17권2호
• /
• pp.20-25
• /
• 1989

This study was carried out in order to investigate the treatment effect of PEG soln which is a common dimensional stabilizer to green log. sawing panel etc, on bonding product including plywood widely-used in secondary processing unit. The 30% concentration of aqueous PEG soln. with molecular weight of 400, 1.000 and 4,000 were prepared respectively, and also dipping the veneer in the PEG soln. spreading the PEG soln. on veneer and mixing the PEG soln. in the adhesive were allowed. Then the ratio of PEG impregnation on veneer, the adhesive strength of plywood were epitomized as follows: The ratio of impregnation by PEG 4,000 at dipping condition was highest. while that by PEG 400 at same condition was lowest. However, the effect of PEG molecular weight on the ratio of impregnation at spreading condition did not occur. 2. The adhesive strength was great in the order of 4,000>400>1,000 in molecular weight of PEG at dipping and spreading conditions. In case of mixing the PEG soln. in the adhesive, the adhesive strength was great in the order of 400>1,000>4,000 in molecular weight of PEG. Throughout three treatment conditions, PEG 400 was relatively favourable with about 10kg/$cm^2$ dry strength. 3. The adhesive strength was great 10 the order of spreading >dipping >mixing condition. 4. Although adhesive strength with the 30% concentration of aqueous PEG soln. was decreased by 35% and over, compared to control (non-treatment) adhesive strength, all types of PEG treatment except mixing the PEG soln. in the adhesive exceeded the standard dry strength for common use panel. 7.5kg/$cm^2$. 5. In warm water-proof test, the adhesive strengths by all PEG treatment conditions were less than the standard wet strength, 7.5kg cot, and also delamination of glue line occured mostly in mixing in the PEG soln. in the adhesive condition.