• IEMEK Journal of Embedded Systems and Applications
• /
• v.1 no.2
• /
• pp.37-42
• /
• 2006

In this paper, we study a problem of providing reliable data transmission in wireless sensor network(WSN). A system with forward error correction9FEC) can provide an objective reliability while using less transmission power than a system without FEC. We propose the use of LDPC codes of various code rate (0.53, 0.81, 0.91) of FEC for WSN. Node-node-node interference is considered in the simulation in addition to AWGN in the channel. It is shown that the rate of 0.91 LDPC coded system obtained 7dB gain in signal to noise ratio over a system without FEC.

• Journal of Information Processing Systems
• /
• v.13 no.6
• /
• pp.1544-1553
• /
• 2017

The network coding mechanism has attracted much attention because of its advantage of enhanced network throughput which is a desirable characteristic especially in a multi-hop wireless network with limited link capacity such as the device-to-device (D2D) communication network of 5G. COPE proposes to use the XOR-based network coding in the two-hop wireless network topology. For multi-hop wireless networks, the Distributed Coding-Aware Routing (DCAR) mechanism was proposed, in which the coding conditions for two flows intersecting at an intermediate node are defined and the routing metric to improve the coding opportunity by preferring those routes with longer queues is designed. Because the routes with longer queues may increase the delay, DCAR is inefficient in delivering real-time multimedia traffic flows. In this paper, we propose a network coding-aware routing protocol for multi-hop wireless networks that enhances DCAR by considering traffic load distribution and link quality. From this, we can achieve higher network throughput and lower end-to-end delay at the same time for the proper delivery of time-sensitive data flow. The Qualnet-based simulation results show that our proposed scheme outperforms DCAR in terms of throughput and delay.

• Korean Journal of Materials Research
• /
• v.29 no.9
• /
• pp.532-541
• /
• 2019

Information and communication technologies are developing rapidly as IC chip size becomes smaller and information processing becomes faster. With this development, digital circuit technology is being widely applied to mobile phones, wireless LANs, mobile terminals, and digital communications, in which high frequency range of GHz is used. In high-density electronic circuits, issues of noise and EMC(Electro-Magnetic Compatibility) arising from cross talk between interconnects or devices should be solved. In this study, sheet-type electromagnetic wave absorbers that cause electromagnetic wave attenuation are fabricated using composites based on soft magnetic metal powder and silicon rubber to solve the problem of electromagnetic waves generated in wireless communication products operating at the frequency range of 2.4 GHz. Sendust(Fe-Si-Al) and carbonyl iron(Fe-C) were used as soft magnetic metals, and their concentrations and sheet thicknesses were varied. Using soft magnetic metal powder, a sheet is fabricated to exhibit maximum electromagnetic attenuation in the target frequency band, and a value of 34.2dB(99.9 % absorption) is achieved at the target frequency.

• Journal of Communications and Networks
• /
• v.18 no.2
• /
• pp.201-209
• /
• 2016

In wireless sensor networks (WSNs) duty cycling has been an imperative choice to reduce idle listening but it introduces sleep delay. Thus, the conventional WSN medium access control protocols are bound by the energy-latency tradeoff. To break through the tradeoff, we propose a radio wave sensor called radio frequency (RF) wakeup sensor that is dedicated to sense the presence of a RF signal. The distinctive feature of our design is that the RF wakeup sensor can provide the same sensitivity but with two orders of magnitude less energy than the underlying RF module. With RF wakeup sensor a sensor node no longer requires duty cycling. Instead, it can maintain a sleep state until its RF wakeup sensor detects a communication signal. According to our analysis, the response time of the RF wakeup sensor is much shorter than the minimum transmission time of a typical communication module. Therefore, we apply duty cycling to the RF wakeup sensor to further reduce the energy consumption without performance degradation. We evaluate the circuital characteristics of our RF wakeup sensor design by using Advanced Design System 2009 simulator. The results show that RF wakeup sensor allows a sensor node to completely turn off their communication module by performing the around-the-clock carrier sensing while it consumes only 0.07% energy of an idle communication module.

• Journal of Advanced Information Technology and Convergence
• /
• v.8 no.2
• /
• pp.147-157
• /
• 2018

In this study, we analyzed an outdoor visible light communication system and implemented it through a simulation. We designed a Reed-Solomon encoder, a variable interleaver structure, and set it to the Institute of Electrical and Electronics Engineers (IEEE) 802.15.7 PHY I specification mode. We also analyzed the performance of an additive white gaussian noise (AWGN) channel environment using a root-raised-cosine (RRC) filter, implemented a MATLAB simulation and analyzed its performance. The results showed a requirement for an additional signal-to-noise ratio (SNR) of approximately 1.5 dB in a 3-ray multipath visible light channel environment than in an AWGN environment.

• Journal of Advanced Navigation Technology
• /
• v.11 no.1
• /
• pp.64-71
• /
• 2007

In this paper, we have designed and fabricated microstrip antenna of S-band for the wireless LAN and the ISM. It array $2{\times}2$ circular patch antenna elements at plane instead of conventional rectangular patch antenna elements. It optimized to size calculated of single patch antenna. The radiation elements distance is array $0.24{\lambda}$. The fabricated circular patch antenna decreased 8% of size compared to the conventional rectangular patch antenna. In the E-plane, designed circular microstrip patch $2{\times}2$ array antenna gain is 12.7[dBi], half power beam width is $40^{\circ}$ and in the H-plane, antenna gain is 12.1[dBi], half power beam width is $45^{\circ}$. Bandwidth is 250[MHz] (VSWR < 2).

• Journal of information and communication convergence engineering
• /
• v.2 no.2
• /
• pp.61-66
• /
• 2004

This paper presents a way to maximize transmission efficiency and reception ability through transmission diversity technology, which can be adapted to wireless multimedia Wireless LAN system. The presented method is a comparative analysis between a case where parameter a for time average is 0.3.1 with consideration of channel presumption with two types of rms delayed spread, which is 50nsec. 150nsec, for the performance analysis of STTC (Space-Time Trellis Code) adopting time-space ciphering method appropriate for MIMO channel, and performance in the case where presumed channel value from long training column section is applied to according frame in a single frame. The result showed that BER brought SNR improvement of l.0dB in $10^{-3}$ when a was 0.3 than adopting only the long training column, and showed increase of general performance improvement for the sake of time average rather than the case without.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.239-246
• /
• 2013

In this paper, a dual-band on-body antenna operating at MICS and ISM band for a wireless medical repeater system is proposed and the antenna performance including the human body effect is investigated. The designed dual-band antenna is comprised of a top patch for ISM band and bottom patch for MICS band. Simulation and measurement was carried out in order to analyze the effects of human body on antenna performance considering real use. The proposed antenna has required impedance bandwidth enough to cover both MICS and ISM bands. The measured peak gains were -12.47 dBi and 1.71 dBi at the each center frequency of MICS and ISM bands, respectively. Furthermore, the antenna has the maximum radiation directed toward the inside of the human body in the MICS band and directed toward the outside in the ISM band. In addition, the return loss property of the antenna is insensitive to human body effects so that the proposed antenna is well suited for the on-body wireless medical repeater system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.6
• /
• pp.1050-1055
• /
• 2001

In this paper we analyze the performance of 2-D PSAM for wireless OFDM systems. We apply the analysis of single-carrier PSAM to the 2-D time-frequency lattice of OFDM. To estimate channel fading, we use interpolation filter which minimizes the average power of error as compensation method and analyze the affects on the system performance of the pilot symbol pattern on the 2-D time-frequency lattice. Finally according to the CP and the Doppler frequency, we analyze the performance of 2-D PSA-16QAM for OFDM systems over frequency selective Rayleigh fading channel model.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.62-65
• /
• 2017

In this paper, three DC Block designs are presented which efficiently meet the need of modern-day compactsize wireless communication systems. As one of the important parts of a complete system design, the proposed microstrip-based DC block with coupled transmission lines efficiently attenuates unwanted frequencies that cause damage to the system. The compact-sized DC block structures are created by incorporating an extended coupled-line section with a radial stub, an enveloped coupled-line section, and using alternate up-down meandering techniques. The structures are analyzed for the L-Band using a high-resistive silicon substrate. At a resonating frequency of 1.575 GHz, the designed DC Block structures have a return loss better than -10 dB, an insertion loss of around -1 dB, and also possess wide pass-band characteristics.