• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1998년도 유체기계 연구개발 발표회 논문집
• /
• pp.91-96
• /
• 1998

The broadband noise generated aerodynamically from a two-bladed axial flow fan has been measured and compared to the result of a self-noise prediction method. The prediction scheme is based on the experimental data set acquired from a series of aerodynamic and acoustic tests of two and three-dimensional airfoil blade sections. For low blade loading case the comparison showed a reasonably good agreement, but as the loading becomes larger the empirical formula overpredict the sound pressure level at high frequency range. This is probably due to the use of stationary wing data for the prediction of rotating blade case, which will be quite different in their vortex strength at the blade tip.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.30-40
• /
• 2007

The implicit discontinuous Galerkin method for the two-dimensional Euler equations was developed on unstructured triangular meshes, which can achieve higher-order accuracy by wing hierachical basis functions based on Legendre polynomials. Numerical tests were conducted to estimate the convergence order of numerical solutions to the Ringleb flow and the supersonic vortex flow for which analytic solutions are available. And, the flows around a circle and a NACA0012 airfoil was also numerically simulated. Numerical results show that the implicit discontinuous Galerkin methods with higher-order representation of curved solid boundaries can be an efficient higher-order method to obtain very accurate numerical solutions on unstructured meshes.

• Journal of Ship and Ocean Technology
• /
• 제8권4호
• /
• pp.10-16
• /
• 2004

A response of a swept wing boundary layer to a single free-stream stationary axial vortex of a limited spanwise extent is considered as an example of typical problems that one can find in laminar-turbulent transition research and control. The response is dominated by streamwise velocity perturbations that grow quasi-exponentially downstream. It is shown that the formation of the boundary layer disturbance occurs for the most part close to the leading edge. The disturbance represents itself a wave packet consisted of the waves with characteristics specific for cross-flow instability. However, an admixture of growing disturbances whose origin can be attributed to transient effects and to a distributed receptivity mechanism is also identified.

• Advances in aircraft and spacecraft science
• /
• 제6권5호
• /
• pp.371-389
• /
• 2019

The implementation of a robust $H_{\infty}$ Control, which is numerically efficient for uncertain nonlinear dynamics, on longitudinal and lateral autopilots is realised for a quarter scale Piper J3-Cub model accepted as an unmanned aerial vehicle (UAV) under the condition of sensor noise and disturbance effects. The stability and control coefficients of the UAV are evaluated through XFLR5 software, which utilises a vortex lattice method at a predefined flight condition. After that, the longitudinal trim point is computed, and the linearization process is performed at this trim point. The "${\mu}$-Synthesis"-based robust $H_{\infty}$ control algorithm for roll, pitch and yaw displacement autopilots are developed for both longitudinal and lateral linearised nonlinear dynamics. Controller performances, closed-loop frequency responses, nominal and perturbed system responses are obtained under the conditions of disturbance and sensor noise. The simulation results indicate that the proposed control scheme achieves robust performance and guarantees stability under exogenous disturbance and measurement noise effects and model uncertainty.

• 한국전산유체공학회지
• /
• 제18권3호
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.

• 한국항공우주학회지
• /
• 제42권7호
• /
• pp.535-543
• /
• 2014

비세장형, 둥근 앞전을 가지고 스팬이 1.0m로 축소된 BWB형 UCAV에 대해 완전난류, 천이 모델을 사용하여 전산해석을 수행하였다. 자유류는 받음각 -4도부터 26도까지 50m/s이며, 평균 시위 기준 레이놀즈수는 $1.25{\times}10^6$이다. 멀티블록 6면체 격자와 함께 완전난류 모델과 천이 모델의 결과를 비교하여 천이효과가 공력 특성에 미치는 영향을 살펴보았다. 풍동 실험과 비교한 결과 양/항력 계수는 해석범위 내에서 잘 일치하였으며, 피칭 모멘트는 높은 받음각에서 작게 예측됨과 동시에 난류모델에 따라 결과가 크게 달라졌다. 압력분포와 skin friction line, 축 방향 속도장을 이용하여 와류구조의 거동과 천이현상이 미치는 영향을 살펴본 결과, 천이효과를 고려하는 것이 UCAV의 정확한 와류 구조와 공력특성 예측에 필요한 것으로 확인하였다.

• 한국항공운항학회지
• /
• 제19권2호
• /
• pp.1-9
• /
• 2011

Several studies on the development for solar powered uninhabited aerial vehicles(UAVs) are under way as the use of the renewable energy becomes more and more important these days. This paper is for the conceptual design by a discrete and iterative method. An initial design point with 1.5 meter wing span is determined in the global design, which deploys the mass and energy balances among each component of UAV including solar cells and airframe. Then, the iteration for subsystems is carried out with the help of Vortex Lattice Method(VLM) to optimize the aircraft configuration and the solar power system. It is demonstrated in simulations that the optimized design increases the flight time from 62 to 120 minutes when the solar power system is installed. Also, the associated dynamic analysis reveals that the designed small aircraft has the acceptable stability and controllability.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.209-212
• /
• 2006

Insect and birds in nature flap their wings to generate fluid dynamic forces that are required for the locomotion. Most of the previous published papers discussed mainly on the effect of flapping parameters such as flapping frequency and amplitude on the thrust at a fixed Reynolds number. However, it is not much known on the values of the flapping parameters that the flapping wing requires to generate the thrust at the low Reynolds number flow. In this paper, the onset of the thrust generation is investigated using the lattice Boltzmann method. The wake patterns and velocity profiles behind a flat plate in heaving oscillation are investigated for the heaving amplitude of 0.5C. The time-averaged thrust coefficient value is investigated by changing the reduced frequency from 0.125 to 3.0 for three values of heaving amplitude (h/C=0.25, 0.325, 0.50). It is also found that the critical Strouhal number over which the flat plate starts to produce the thrust is around 0.1 and the thrust is an exponential function of the Strouhal number.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.473-473
• /
• 2009

There have been many academic researches on the aerodynamic design of wind turbine based on blade element method (BEM) and momentum theory (MT, or actuating disk theory). However, in the real world, the turbine blade design requires many additional constraints more than theoretical analysis. The standard procedure is studied in the present paper to design new blades for the wind turbine system ranged from the small size from 1 to 10 kW. From the experience of full design of a 10 kW blade, the authors tried to set up a standard procedure for the aerodynamic design based on IEC 61400-2. Wind-turbine scale, rotating speed, and geometrical chord/twist distribution at the segmented span positions are calculated with a suitable BEM/MT code, and the geometrical shape of tip and root should be modified after considering various parameters: wing-tip vortex, aerodynamic noise, turbine efficiency, structural safety, convenience of fabrication, and even economic factor likes price, etc. The evaluated data is passed to the next procedure of structural design, but some of them should still be corresponded with each other: the fluid-structure interaction is one of those problems not yet solved, for example. Consequently, the design procedure of small wind-turbine blades is set up for the mass production of commercial products in this research.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권1호
• /
• pp.55-65
• /
• 2017

Underwater torpedo has control fin with very low aspect ratio due to launching from limited size of cylindrical torpedo tube. If the aspect ratio of control fin of underwater vehicle is very low three-dimensional flow around control fin largely reduces control forces. In this study, the end plate was applied to reduce the three-dimensional flow effects of partially movable control fin of underwater vehicle. Through numerical simulations the flow field around control fin was examined with and without end plate for different flap angles. The pressure, vorticity, lift and torque on the control fin were analyzed and compared to experiments. The comparison have shown a reasonable agreement between numerical and experimental results and the effect of end plate on a low aspect ratio control fin. When the end plate was attached to the movable control fin, the lift increased and the actuator shaft torque did not significantly change. As this means less consumption of the actuator shaft torque compared to the control fin that has the same control force, the inner actuator capacity can be reduced and energy consumption can be saved. Considering this, it is expected to be effectively applied to the control fin design of underwater vehicles such as torpedoes.