• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.2
• /
• pp.70-85
• /
• 2006

The supersonic flutter suppression of a cantilevered plate wing is studied with the finite element method and the quasi-steady aerodynamic theory. We suppress wing flutter by using piezoelectric materials and electric devices. Two approaches to flutter suppression using piezoelectric materials are presented; an energy-recycling semi-active approach and a negative capacitance approach. To assess their flutter suppression performances, we simulate flutter dynamics of the plate wing to which piezoelectric patches are attached. The critical dynamic pressure drastically increases with our flutter control using a negative capacitor.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2023-2028
• /
• 2008

In present study, the flow field near the fin surface of plate fin - oval tube heat exchanger with delta wing vortex generator was numerically analyzed. As results, the well developed vortex behind delta wing was observed. These vortex can improve heat transfer fin surface behind delta wing vortex generators.

• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.2
• /
• pp.104-109
• /
• 2006

In this study, the equivalent plate model is developed using a finite element method(FEM) based on the first order shear deformation theory(FSDT). The substructure synthesis method is used to consider the control surface. For the verification of the equivalent model, the results of free vibration analysis are compared with the ones of 3D wing structure modeled by using the MSC/NASTRAN.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.1
• /
• pp.33-43
• /
• 2007

Using the more common conventional chordwise aerodynamic approach, flapping a flat plate wing with zero degree chordwise pitch angle of attack and no relative wind should not produce lift. However, in hover, with no forward relative velocity and zero degree chordwise pitch angle of attack, flapping flat plate wings does in fact produce lift. In the experiments peformed for this paper, the flapping motion is considered pure(downstroke and upstroke) with no flapping stroke plane inclination angle. No changes in chordwise pitch angle are made. The total force is measured using a force transducer and the net aerodynamic force is determined from this measured total force by subtracting the experimentally determined inertial contribution. These experiments were repeated at various flapping frequencies and for various wing planform sizes for flat plate wings. The trends in the aerodynamic lift variation found using a force transducer have nearly identical shape for various flapping frequencies and wing planform sizes.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2390-2395
• /
• 2007

The present research was experimentally performed to analyze the effect of delta-wing vortex generators(DWVG) on the heat transfer of fin surface of the plate fin-oval tube. The local heat transfer coefficient of the fin surface for four kinds of DWVG's arrangement was measured by the naphthalene sublimation technique for Reynolds numbers ranging from 2000 to 3200. The results showed that the heat transfer of the plate fin-oval tube can be significantly enhanced by DWVG for relatively low Reynolds numbers.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.14 no.2
• /
• pp.39-44
• /
• 2006

The unsteady vortex lattice method is used to model lead-lag in flapping motions of a rectangular flat plate wing. The results for plunging and pitching motions were compared with the limited experimental results available and other numerical methods. They show that the method is capable of simulating many of the features of complex flapping flight. The lift, thrust and propulsive efficiency of a rectangular flat plate wing have been calculated for various lead-lag motion and reduced frequency with an amplitude of flapping angle(20o). To describe a motion profile of wing tip such as elliptic, line and circle, the phase difference of flapping and lead-lag motion was changed. And the effects of the motion profile on the aerodynamic characteristics of the flapping wing are discussed by examination of their trends.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.6 no.1
• /
• pp.7-20
• /
• 1998

A reduction of induced drag is an important problem in order to save fuels. In this study, the aerodynamic characteristics of wing tip devices to reduce induced drag, such as end plate, plain ring, helical ring wing tip device, was experimentally investigated in a low speed wind tunnel. The experimental results showed that the wing model with a helical ring wing tip device reduced a induced drag and increased lift-drag ratio.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2002.11a
• /
• pp.95-100
• /
• 2002

The wing in ground effect (WIG) ship is an energy saying vessel that uses the lift from its air-wing along with the lift increase from the ground effect by flying low above the sea surface. The WIG Ship should consist of thin plate in order to float on the sea and to fly in the air. Therefore, the structure of WIG, Ship has very thin and light shell plate and stiffener like stringer and frame has comparatively large cross section area. This structure makes shell plate nearly pure shear field when shell plate is pressed by in-plane load. This complex thin plate structure of WIG Ship can he considered as a closed section beam which makes it possible to analyze structure response of WIG Ship affected by shear load and bending load. In this respect, the present study will show basic theory for analysing shear stress and focus on the analysis of structure strength of model WIC Ship's wing.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.56-61
• /
• 2002

Experimental flutter test for a flat plate wing is performed and the flutter analysis methods are verified by comparing with the experimental results. Wing model and experimental equipment are established in the subsonic wind-tunnel. From the response of the wing, the flutter speed is estimated by using the system identification technique. MSC/NASTRAN, V-g method and root-locus method are used for the flutter analysis of the wing. The computed flutter speed is compared with the estimated one from the experiment, and they show good agreement. Wing model in the present study can be used as a benchmark model for the flutter analysis.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.9-12
• /
• 2005

Recently, research on the morphing wing is an interesting issue to develop the capability of the wing such as improving the lift and reduction of drag during the operation of an aircraft by changing the wing shape from one configuration to another. A more efficient weight reduction of the wing using smart or morphing wing concept can be achieved in comparison with the conventional flaps. In this study, it is investigated the behaviors of the morphing wing using Macro Fiber Composite (MFC) actuators. Generally, MFC is the piezocomposite actuator with the rectangular PZT fiber and epoxy matrix, and uses the interdigitated electrode to produce more powerful actuation in the in-plane direction. Furthermore, it can produce the twisting actuation as compared with the traditional PZT actuators. In the formulation, the first-order shear deformation plate theory is used, and finite element method is adopted in the numerical analysis of the model. Results show the characteristics of the static behavior of the morphing wing according to the change of the actuation voltage.