• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.220-224
• /
• 1999

Sliding wear test was employed to determine the effect of whisker content and orientation on the firiction and wear behavior of SiC whisker reinforced alumina. Composites containing unidirectionally oriented whiskers were prepared by a modified tape casting followed by lamination, binder removal and hot pressing in order to align the whiskers in the tape casting direction. Wear coefficients on three directions were measured; parallel and normal to the tape casting direction on the tape casting surface and normal to lamination direction on surfnce normal to the tape casting direction. In the effect of whisker orientation, the highest wear rate was obtained in the direction parallel tape casting direction and the lowest in the direction normal to lamination direction at all temperatures. Silicon oxide layer amoothing the surface was detected by energy dispersive X-ray analysis on the worn surface.

• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.483-489
• /
• 1999

Gas pressure sintered silicon nitride based composites with 3 wt% $\beta$-Si3N4 whiskers were prepared and change of properties according to the whisker orientation and sintering temperature was studied. The tapes with whiskers were fabricated by two different method ; conventional tape casting and a modified tape casting by using guide pins,. Orientations of the whiskers were controlled by different stacking sequences of the sheets cut from the tape. Samples were fully densified by gas pressure sintering at 2148-2273K. As the sintering temperature increased size of the large elongated grains increased. In case of unidirectional samples sintering shrinkage normal to the whisker alignment direction was larger than that of parallel to the direction and the shrinkage anisotropy increased slightly as sintering temperature increased. As sintering temperature increased the crack length parallel to whisker alignment direction became shorter but that normal to the direction did not depend on sintering temperature. In case of cross-plied samples the anisotropy of mechanical properties disappeared.

• The Korean Journal of Ceramics
• /
• 제5권1호
• /
• pp.12-18
• /
• 1999

Alumina matrix composites reinforced with up to 20vol% of aligned SiC whiskers were fabricated by tape casting and hot pressing. Alumina composited with randomly distribution SiC whiskers were also fabricated in order to investigate the effect of whisker alignment on properties of the composites. XRD and optical microscopy were used to examine the whisker orientation. The fracture toughness increased with increasing whisker content, and it was higher in the direction normal to the tape casting direction.

• 한국세라믹학회지
• /
• 제36권1호
• /
• pp.43-49
• /
• 1999

0~5 wt%의 $\beta$-Si3N4 whisker를 첨가한 질화규소 가스압 소결체를 제작하였다. 첨가된 whisker들은 tape casting을 응용하여 tape 내에서 일방향으로 배열하였으며, 제작된 tape로부터 절취된 sheet들의 적층 과정을 변화하여 다양한 미세구조를 갖는 성형체를 제작하였다. 가스압 소결을 통하여 치밀화된 소결체의 조대결정립은 성형체의 whisker와 같은 방향성을 가졌으며, 소결수축률과 기계적 특성 등도 이러한 다양한 미세구조상의 특징과 일관된 결과를 나타내었다. Whisker를 일방향으로 배열하였을 경우, 소결수축률은 whisker 배열 방향과 평행한 방향보다 수직한 방향으로 크게 일어났을 때, whisker 함량이 증가함에 따라 수축률의 차이가 증가하였다. Indentationi crack length는 whisker 함량이 증가함에 따라 whisker 배열 방향과 수직한 방향의 균열 길이는 더 짧아졌고, 그와 평행한 방향의 균열 길이는 길어졌다. Whisker 첨가에 의해 결정립이 더 크게 성장하였으나 강도는 whisker를 첨가하지 않을을때보다 낮지 않았다. Whisker 배열 방향을 90$^{\circ}$ 및 45$^{\circ}$ 간격으로 엇갈리게 적층하였을 경우에는 특성의 이방성이 나타나지 않았다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.25-29
• /
• 1998

Sliding wear test and surface characterization techniques such as micro-Raman spectroscopy were employed to determine the effect of whisker content and orientation on the friction and wear behavior of SiC whisker reinforced alumina. Composites containing unidirectionally oriented whiskers were fabricated by novel technique Addition of SiC whiskers up to 20 vol.% lowered the friction and improved wear resistance. The results of this study indicated that highly disordered graphite and size of the layer behind the whiskers were responsible for variation of wear rate and friction coefficient.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.88-95
• /
• 2001

Silicon nitride based ceramics reinforced with 3wt% Si$_{3}$N$_{4}$ whisker was prepared by tape casting to investigate the effect of microstructure on erosion behaviors. Hardness and fracture toughness were measured with prepared specimens. A gas blast type erosion tester was used to examine the erosion behavior of the specimens with different impact directions and angles. The erosion rate increases with increasing impact angle. Erosion rate of the silicon nitride ceramics also depends on the grain orientations, The erosion rate was lowered when impaction direction was parallel to the grain orientation This result was explained by the crack deflection and bridging due to the grain orientation.

• 한국세라믹학회지
• /
• 제43권3호
• /
• pp.152-155
• /
• 2006

Silicon carbide ceramics seeded with 10-30 wt% SiC whiskers are fabricated by hot pressing and annealing. A quantitative texture analysis including calculation of the Orientation Distribution Function (ODF) is used for obtaining the degrees of preferred orientation of the fabricated samples. The microstructure and crystallographic texture are discussed with respect to the effect of ${\beta}-SiC$ whisker seeds on the resulting fracture toughness values. The SEM microstructures and the texture data reveal a correlation between texture and fracture toughness anisotropy.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.377-381
• /
• 1998

Wear behaviors of unidirectionally oriented $Si_3N_{4w)/Si_3N_4$ composites, sintered at different temperatures with different alignments of whiskers, have been studied in parallel and perpendicular sliding directions with respect to the orientation of the whiskers by using a ball-on-disk reciprocating sliding apparatus. The results show that wear rate in parallel direction is much greater than that in perpendicular direction. With decreasing alignment of the whiskers, the wear rate decreases in parallel sliding direction and increases in perpendicular direction. With increasing sintering temperature, the wear rate increases obviously in both parallel and perpendicular directions.