• 한국정밀공학회지
• /
• 제32권7호
• /
• pp.591-595
• /
• 2015

The roller rig tester for safety performance evaluation of wheel derailment is a test facility which can give the test load condition to the test wheel, similar to the actual dynamic condition in actual running condition. This study describes the evaluation result on the durability of the resilient wheel equipped with the ring damper and the damping material, and installed in the half part of a full scaled bogie in combination with the primary spring when it rotates under the dynamic condition. The evaluation result on durability of resilient wheel after load test of 2 million cycles shows that the safety of wheel is not affected by the applied load in visual inspection and nondestructive test, however, in the bolt used for fastening the ring damper to the wheel the loosening was found. Accordingly the use of self-locking nut and washer is recommended.

• 한국방재학회 논문집
• /
• 제10권1호
• /
• pp.29-34
• /
• 2010

본 연구에서는 차량의 주행으로 인한 동적하중이 프리캐스트 바닥판의 손상에 미치는 영향에 대하여 살펴보았다. 실제 주행조건에 근접한 윤하중 시험차량 및 프리캐스트 바닥판을 제작하였으며, 정적재하시험 및 반복 윤하중 시험을 통하여 패널의 접합부, 시험시편의 처짐량, 베딩 층, 전단 포켓부의 거동을 분석하였다. 프리캐스트 바닥판 패널-1, 패널-2, 패널-3을 연결, 정적재하시험과 윤하중 재하시험 결과를 분석하면 변형률과 처짐의 경우 최대값에는 큰 차이가 없으나 정적재하시험은 패널-2에서 처짐이 가장 크게 발생한 반면, 윤하중 재하시험은 변형률이 전단 포켓부에서 가장 많이 발생하였으며, 중앙부 패널-2에서보다 패널-1과 패널-3에서 최대 처짐이 발생하는 차이를 보였다.

• International Journal of Automotive Technology
• /
• 제7권6호
• /
• pp.681-686
• /
• 2006

The current flat type side slip tester measures only the total side slip. Therefore, measurement techniques which can be used to determine the side slip for each alignment element were examined. Because the side slip related to the camber angle varies depending on the unit load per travel wheel while the side slip related to the toe angle does not on the unit per travel wheel, but depends only on the direction of the tire, the side slip for each alignment element can be determined separately.

• 한국도로학회논문집
• /
• 제15권1호
• /
• pp.103-110
• /
• 2013

PURPOSES: The objective of this study is to analyze and evaluate the behavior of orthotropic steel bridge deck pavement using three-dimensional finite element analysis and full-scale wheel load testing. METHODS: Since the layer thickness and material properties used in the bridge deck pavement are different from its condition, it is very difficult to measure and access the behavior of bridge deck pavement in the field. To solve this problem, the full-scale wheel load testing was conducted on the PSMA/Mastic bridge deck pavement and the deflection of bridge deck and horizontal tensile strain on top of pavement were measured under the loading condition. Three-dimensional finite element analysis was conducted to predict the behavior of bridge deck pavement and the predicted deflection and tensile strain values are compared with measured values from the wheel loading testing. RESULTS: Test results showed that the predicted deflections are 10% lower than measured ones and the error between predicted and measured horizontal tensile strain values is less than 2% in the critical location. CONCLUSIONS: The fact indicates that the proposed the analysis is found to be accurate for estimating the behavior of bridge deck pavements.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.1247-1248
• /
• 2012

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.41-50
• /
• 1998

In this study, to investigate a characteristics of slip ratio control of H.C.U for ABS, half car model tester were developed and a new H.C.U. was compactly designed comparing to the commercical H.C.U. for ABS. In half car model tester, variable inertia wheel has been used to load the car weights and braking forces according to the road surface conditions which were realized by pneumatic cylinder. And solenoid valves using P.W.M. (Pulse Width Modulation) method were installed in the new H.C.U The slip ratio characteristics of tire had been measured using half car model tester and the results were used in the control simulation for a new H.C.U.

• 한국정밀공학회지
• /
• 제32권7호
• /
• pp.603-609
• /
• 2015

Railway vehicles driven by wheels obtain force required for propulsion and braking by adhesive force between wheels and rails, this adhesive force is determined by multiplying adhesion coefficient of the friction surface by the applied axle load. Because the adhesion coefficient has a peak at certain slip velocity, it is important to determine the maximum values of the friction coefficient on the contact area. But this adhesive phenomenon is not clearly examined or analyzed. Thus we have developed new test procedure using the scaled adhesion test-bench for analyzing of the adhesion coefficient between wheel and rail. This adhesion test equipment is an experimental device that contacts mutually with twin disc which are equivalent to wheels and rails of railway vehicles.

• 한국도로학회논문집
• /
• 제7권3호
• /
• pp.1-10
• /
• 2005

본 연구에서는 일반 아스팔트 포장에 비해 설계수명을 2배 이상 증대시켜 보수주기를 증진하고 보수비용 및 사용자 비용을 절감할 수 있는 장수명 아스팔트 포장에 대한 포장가속시험 (APT)을 수행하였다 먼저 본 연구에서 개발된 장수명 포장용 고강성기층 혼합물에 대한 기초적인 물성시험을 수행하였다. 포장의 지지력을 비교하고 피로 및 소성변형에 대한 저항성을 평가하기 위하여 일반 및 고강성 기층으로 구성된 총 4개의 시험단면을 건설하였다. 또한 일반 및 고강성 단면은 각각 얇은 단면과 두꺼운 단면으로 구성되었다. 다양한 교통하중에 대한 아스팔트 기층하단의 인장변형률을 측정하였으며 시험결과 고강성 단면의 인장변형이 일반단면에 비해 적게 발생되는 것을 확인하였다. 기층 단면이 얇은 포장단면에 대한 APT 시험결과 윤하중이 180,000회 재하될 때까지 균열은 발생하지 않았다. 기층단면이 두꺼운 포장에 대해 윤하중 90,000회 재하시 일반단면은 5.3mm, 고강성 단면은 3m의 소성변형이 발생하였다. 본 연구에서 개발된 고강성 혼합물은 소성변형 및 피로균열에 대한 저항성이 우수하기 때문에 장수명 포장용 기층재로서 적합한 것으로 판단된다. 또한 다양한 구조해석 결과 일반 혼합물 대신 고강성 혼합물을 사용할 경우 포장의 하중지지력이 증가하기 때문에 아스팔트층의 단면두께를 최소 5cm 이상 줄일 수 있을 것으로 판단된다.

• 한국도로학회논문집
• /
• 제17권6호
• /
• pp.37-45
• /
• 2015

PURPOSES : The purpose of this study is to validate the design criteria of the concrete modular road system, which is a new semi-bridge-type concept road, through a comparison of numerical analysis results and actual loading test results under static axial loads. METHODS : To design the semi-bridge-type modular road, both the bridge design code and the concrete structural design code were adopted. The standard truck load (KL-510) was applied as the major traffic vehicle for the design loading condition. The dimension of the modular slab was designed in consideration of self-weight, axial load, environmental load, and combined loads, with ultimate limit state coefficients. The ANSYS APDL (2010) program was used for case studies of center and edge loading, and the analysis results were compared with the actual mock-up test results. RESULTS : A full-scale mock-up test was successfully conducted. The maximum longitudinal steel strains were measured as about 35 and 83.5 micro-strain (within elastic range) at center and edge loading locations, respectively, under a 100 kN dual-wheel loading condition by accelerating pavement tester. CONCLUSIONS : Based on the results of the comparison between the numerical analysis and the full-scale test, the maximum converted stress range at the edge location is 32~51% of the required standard flexural strength under the two times over-weight loading condition. In the case of edge loading, the maximum converted stresses from the Westergaard equation, the ANSYS APDL analysis, and the mock-up test are 1.95, 1.7, and 2.3 times of that of the center loading case, respectively. The primary reason for this difference is related to the assumption of the boundary conditions of the vertical connection between the slab module and the crossbeam module. Even though more research is required to fully define the boundary conditions, the proposed design criteria for the concrete modular road finally seems to be reasonable.

• Composites Research
• /
• 제21권1호
• /
• pp.40-45
• /
• 2008

자동차용 유압브레이크 고무호스 어셈블리 제품은 자동차에 장착되어 실제로 사용 중에 가압, 굽힘, 비틀림, 열하중 등의 복합적인 스트레스를 받는다. 고무호스의 재질은 EPDM(ethylene-propylene diene monomer)고무와 PVA(polyvinyl acetate)섬유 보강층 그리고 중간고무로 NR(natural rubber)고무가 사용되고 있다. 고무호스 어셈블리 제품의 내구성과 파괴 메커니즘을 조사하기 위해 굽힘과 비틀림의 반복하중 사이클 수가 10만, 20만, 30만, 40만, 최종파열 사이클 수까지 되도록 시험하였다. 유압브레이크 고무호스의 초기크랙 발생을 알아보기 위해 제품 시험편을 다이아몬드 휠커터를 이용하여 수직 절단하여 폴리싱한 후 광학현미경과 주사형 전자현미경(SEM)으로 단면을 관찰하였다. 40만 사이클의 피로하중을 받은 시험편을 보면 외면고무와 PVA섬유 사이의 계면을 따라 길이 1mm의 층간분리가 일어났으며, 이러한 손상은 외면고무의 표피층으로 균열을 진전시켜 고무호스를 최종적으로 찢어지게 하는 것이다.