• Journal of Astronomy and Space Sciences
• /
• v.24 no.3
• /
• pp.249-260
• /
• 2007

The crustal deformation due to Ocean Tide Loading (OTL) in the Korean peninsula reaches up to ${\sim}3cm$ in the vertical direction. Considering that the achievable positioning accuracy of current state-of-the-art space geodesy technologies is at the several millimeter level, the centimeter-level OTL effect should be precisely modelled and corrected for. This study begins with comparison of ocean tide models and validation of OTL-prediction softwares. Different ocean tide models caused about ${\sim}6mm$ RMS differences in the vertical deformation in the Kyung-gi Bay area. When we analyzed the OTL displacements in the Seoul, Ulsan, and Seogwipo areas where three VLBI observatories are planned to be installed, the maximum displacement of ${\sim}3.5cm$ was predicted in the Seogwipo area and ${\sim}2cm$ in the Seoul and Ulsan areas. When the OTL corrections were not applied in the GPS data processing, the OTL effect propagates into the Zenith Wet Delay (ZWD) estimates, and the scale factor between ZWD differences and OTL displacements was 3.72.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.3
• /
• pp.47-58
• /
• 2001

For finding both ways of recycling the wood and plastic wastes and solving the problem of free formaldehyde gas emission through manufacturing wood particle-polypropylene fiber composite board without addition of formaldehyde-based thermosetting resin adhesive, control particleboards and nonwoven web composite boards from wood particle and polypropylene fiber formulation of 50 : 50, 60 : 40, and 70 : 30 were manufactured at density levels of 0.5, 0.6, 0.7, and 0.8 g/$cm^3$, and were tested both in the physical and mechanical properties according to ASTM D 1037-93. In the physical properties, control particleboard had significantly higher moisture content than composite board. In composite board, moisture content decreased with the increase of target density only in the board with higher content of polypropylene fiber and also appeared to increase with the increase of wood particle content at a given target density. Control particleboard showed significantly greater water absorption than composite board and its water absorption decreased with the increase of target density. In composite board, water absorption decreased with the increase of target density at a given formulation but increased with the increase of wood particle content at a given target density. After 2 and 24 hours immersion, control particleboard was significantly higher in thickness swelling than composite board and its thickness swelling increased with the increase of target density. In composite board, thickness swelling did not vary significantly with the target density at a given formulation but its thickness swelling increased as wood particle content increased at a given target density. Static bending MOR and MOE under dry and wet conditions increased with the increase of target density at a given formulation of wood particle and polypropylene fiber. Especially, the MOR and MOE under wet condition were considerably larger in composite board than in control particleboard. In general, composite board showed superior bending strength properties to control particleboard, And the composite board made from wood particle and polypropylene fiber formulation of 50 : 50 at target density of 0.8 g/$cm^3$ exhibited the greatest bending strength properties. Though problems in uniform mixing and strong binding of wood particle with polypropylene fiber are unavoidable due to their extremely different shape and polarity, wood particle-polypropylene fiber composite boards with higher performance, as a potential substitute for the commercial particleboards, could be made just by controlling processing variables.

• Analytical Science and Technology
• /
• v.34 no.6
• /
• pp.251-258
• /
• 2021

Knives are most frequently used as weapons in violent crimes. Criminals leave behind knife sheaths made of paper and tape at crime scenes. It is difficult to develop fingerprints using tape attached to a porous surface, resulting in the need to explore effective techniques for identifying fingerprints as well as the distribution of fingerprints on each surface, when evidence such as paper knife sheaths are found. In this study, 50 knife sheaths were prepared. The cyanoacrylate fuming (CA fuming) method was applied to develop fingerprints on the non-adhesive side of the tape, and a dual-purpose 1,2-indanedione/Zn (1,2-IND/Zn) reagent was used to separate tape from paper while simultaneously developing fingerprints on the paper. The fingerprints on the adhesive side of the tape were developed using Wet Powder Black^®. Using the R statistical analysis program (The R Foundation for Statistical Computing), we used a heat map to indicate the location of fingerprints developed from each surface. More fingerprints were detected at the ends than in the center of the adhesive side of the tape, and although the non-adhesive sides of tape and paper did not present clear distribution patterns, many fingerprints were developed that had sufficient clarity for personal identification. The results of this study may be applicable for processing evidence when paper sheaths are found at crime scenes.

• The Korean Journal of Food And Nutrition
• /
• v.29 no.4
• /
• pp.465-473
• /
• 2016

This study was conducted in order to investigate the antioxidant capabilities and quality characteristics of instant porridge made of foxtail millet (Setaria italica Beauv.) from different varieties with different endosperm characteristics and processing using different methods. The two foxtail millet varieties used in this study were waxy foxtail millet, 'Samdachal', and non-waxy foxtail millet, 'Samdame'. The means of processing food to create instant porridge were dry cereal frying, wet cereal frying, freeze drying after steaming, popping, and no treatment. The WAI (water absorption index) of instant porridge made of waxy foxtail millet was higher than that of non-waxy foxtail millet, and popping created the highest WAI among the treatments tested. Whean we analyzed RVA characteristics of non-waxy foxtail millet instant porridge, peak viscosity and setback values were decreased in all processed foxtail millet instant porridge compared to non-waxy foxtail millet instant porridge. In waxy foxtail instant porridge, the peak and final viscosities of processed treated instant porridge increased. The viscosity just after pouring hot water into the instant porridge was higher in waxy foxtail millet porridge treated by freeze drying after steaming, popping, and wet cereal frying; the viscosity of non-waxy foxtail porridge was increased after popping as compared with the other treatments. The polyphenol contents and antioxidant activities were increased in all processed, treated-instant porridge except for freeze dried porridge after steamingnt. The popping treatment showed the highest polyphenol contents (1.5 fold), and ABTS antioxidant activity (1.2 fold), compared to no treatment. Non-waxy foxtail millet porridge produced by popping earned the highest sensory evaluation scores.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.7
• /
• pp.488-494
• /
• 2012

This study was conducted to determine the optimal ratio of sludges from milk processing industry (MPS), paper-mill industry (PMS) and night-soil treatment plant (NSS) for vermicomposting. Five different ratios, 0 : 80 : 20 (MPS-0), 25 : 60 : 15 (MPS-25), 50 : 40 : 10 (MPS-50), 75 : 20 : 5 (MPS-75), and 100 : 0 : 0 (MPS-100 : control) MPS : PMS : NSS by wet weight were tested in a small plot experiment. The experiment for each mixing ratio was performed for 2 weeks with the three replications. MPS-100 (100 : 0 : 0) only had the highest decomposition rate with 19.9%, followed by MPS-25, MPS-50, MPS-75 and MPS-0 with 19.5, 19.1, 17.6 and 16.7%, respectively. Except for MPS-100, Vermicomposting resulted in increase in ash, T-P, $NO_2{^-}-N$, $NO_3{^-}-N$, Mg, K, As, Cd and Cu, whereas moisture, VS (Volatile Substance), TKN (Total Kjeldahl Nitrogen), $NH_4{^+}-N$, Ca, Hg and Pb were lower in the final cast than the initial feed mixture. Meanwhile Zn showed very slight difference and Cr and Ni did not show any tendency between the feed mixture and the final cast. In the case of MPS-100, where the decomposition rate was the highest, all the heavy metals in the final cast except for Hg were increased. All the vermicomposts produced from five different mixing ratios of the vermicomposting sludges met the Korea Standard as by-product compost.

• Journal of Positioning, Navigation, and Timing
• /
• v.3 no.4
• /
• pp.131-141
• /
• 2014

Over the last decade, the Global Navigation Satellite System (GNSS) has been increasingly utilized as a meteorological research tool. The Korea Astronomy and Space Science Institute (KASI) has also been developing a near real-time GNSS precipitable water vapor (PWV) information management system that can produce a precise PWV for the Korean Peninsula region using GNSS data processing and meteorological measurements. The goal of this paper is to evaluate whether the precise point positioning (PPP) strategy will be used as the new data processing strategy of the GNSS-PWV information management system. For this purpose, quality assessment has been performed by means of a comparative analysis of the troposphere zenith total delay (ZTD) estimates from KASI PPP solutions (KPS), KASI network solutions (KNS), and International GNSS Service (IGS) final troposphere products (IFTP) for ten permanent GNSS stations in the Korean Peninsula. The assessment consists largely of two steps: First, the troposphere ZTD of the KNS are compared to those of the IFTP for only DAEJ and SUWN, in which the IFTP are used as the reference. Second, the KPS are compared to the KNS for all ten GNSS stations. In this step, the KNS are used as a new reference rather than the IFTP, because it was proved in the previous step that the KNS can be a suitable reference. As a result, it was found that the ZTD values from both the KPS and the KNS followed the same overall pattern, with an RMS of 5.36 mm. When the average RMS was converted into an error of GNSS-PWV by considering the typical ratio of zenith wet delay and PWV, the GNSS-PWV error met the requirement for PWV accuracy in this application. Therefore, the PPP strategy can be used as a new data processing strategy in the near real-time GNSS-PWV information management system.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.22-24
• /
• 1974

1. Object and importance of the research. The exports of plywood are increasing annually and it has ranked first in the world market because of the high quality product developed and manufactured using modern techniques. However, it is known that the exports of the other wood products, except plywood, is inactive because of their low quality. Accordingly, to increase the exports of various wood products investigations were carried out on kiln drying techniques to improve the quality of the wood. 2. The details and scope of the research Wet wood should be kiln dried before use to prevent various drying defects such as distortion, shrinkage etc, which would develop after processing, and also wet wood is not suitable for cutting, gluing and finishing. Therefore, the kiln drying properties of lumber from such species as Persimmon, Oak, Ramin and Meranti which are used in large quantity for manufacturing exporting wood products have been studied. Also the real state of kiln drying industry in Korea was investigated. 3. Results and proposal for practical use of the research 3. 1 Results of the research 3.1.1 The end checks and the time for drying from intial moisture content of about 40 percent to 5 percent moisture content in ovendry were investigated as Table 1. 3.1.2 The kiln dried results, for 30mm stock, which are presented by using kiln schedule Table 2 are as Table 3. 3.1.3 The kiln schedule for Persimmon which has a normal drying properties is given in Table 4. However, the persimmon which has easy checking properties should be air dried under a relative humidity of above 85% until reaching about 25 percent moisture content. 3.1.4 The kiln schedules for ramin, meranti and oak are given respectively as follows. Ramin kiln schedule ............ Table 5 and Table 6 Meranti kiln schedule ............ Table 7 Oak kiln schedule ............ Table 8 3.2 Proposal for practical use of the research Firms using the above species should be informed the results of the research so they can be used to preventing drying defects and shortening drying time.

• Clean Technology
• /
• v.27 no.4
• /
• pp.341-349
• /
• 2021

In combustion facilities, the nitrogen and sulfur in fossil fuels react with oxygen to generate air pollutants such as nitrogen oxides (NO_X) and sulfur oxides (SO_X), which are harmful to the human body and cause environmental pollution. There are regulations worldwide to reduce NO_X and SO_X, and various technologies are being applied to meet these regulations. There are commercialized methods to reduce NO_X and SO_X emissions such as selective catalytic reduction (SCR), selective non-catalytic reduction (SNCR) and wet flue gas desulfurization (WFGD), but due to the disadvantages of these methods, many studies have been conducted to simultaneously remove NO_X and SO_X. However, even in the NO_X and SO_X simultaneous removal methods, there are problems with wastewater generation due to oxidants and absorbents, costs incurred due to the use of catalysts and electrolysis to activate specific oxidants, and the harmfulness of gas oxidants themselves. Therefore, in this research, microbubbles generated in a high-pressure disperser and reducing agents were used to reduce costs and facilitate wastewater treatment in order to compensate for the shortcomings of the NO_X, SO_X simultaneous treatment method. It was confirmed through image processing and ESR (electron spin resonance) analysis that the disperser generates real microbubbles. NO_X and SO_X removal tests according to temperature were also conducted using only microbubbles. In addition, the removal efficiencies of NO_X and SO_X are about 75% and 99% using a reducing agent and microbubbles to reduce wastewater. When a small amount of oxidizing agent was added to this microbubble system, both NO_X and SO_X removal rates achieved 99% or more. Based on these findings, it is expected that this suggested method will contribute to solving the cost and environmental problems associated with the wet oxidation removal method.

• Fashion & Textile Research Journal
• /
• v.14 no.5
• /
• pp.866-877
• /
• 2012

The natural dyeing of hanji cotton fabrics with guava leaf extract was investigated. The temperature and time of dyeing were $40^{\circ}C$ and $90^{\circ}C$ for eighty minutes, respectively. In addition, the dyebath has been set at pH 5. Sn pre-mordanted fabrics showed the highest K/S value. Regardless of dyeing temperature, K/S values were high when Al, Cu, Fe-mordanted fabrics were dyed in post-mordanting and Sn-mordanted fabrics in pre-mordanting. The dyeing equilibrium was shown at the fourth time of repeated dyeing. In the processing of hanji cotton fabrics, K/S value was high when hanji cotton fabric was treated with soybean milk at $90^{\circ}C$. Similar K/S value of dyeing was shown when fabrics were processed with chitosan, regardless of dyeing temperature. High K/S value of dyeing was seen when fabrics processed with gallnut tannin at 40. Fabrics dyed with acidic water extract showed yellowish color. Fabrics dyed with alkaline water extract showed reddish color, and fabrics dyed with ethanol extract showed greenish yellow color. In case of Sn-mordanted fabrics, the washing fastness level was between 3 to 4, and other dyed fabrics showed low fastness. The dry cleaning fastness also showed very excellent result with level 4-5. The rubbing fastness of the fabrics was better in dry rubbing than in wet rubbing. For the light fastness, all dyed fabrics showed low fastness. For antibacterial activity, the dyed fabrics with guava leaf extract showed 99.9% of high antibacterial activity. Hanji cotton fabric maintained certain deodorization in the state of raw fabric. All dyed fabrics showed higher UV protection rate than control fabric.

• Journal of the Korean Ceramic Society
• /
• v.45 no.8
• /
• pp.477-481
• /
• 2008

$Eu^{2+}$ and $Dy^{3+}$ co-doped strontium aluminate, $SrAl_2O_4$ long phosphorescent phoshor was fabricated and its photoluminescence was characterized. The phosphor, $SrAl_2O_4:Eu^{2+},Dy^{3+}$ was synthesized by a coprecipitation in which metal salts of $Sr(NO_3)_2$, $Al(NO_3)_3{\cdot}9H_2O$, were dissolved in $(NH_4)_2CO_3$ solution with adding $Eu(NO_3)_3{\cdot}5H_2O$ and $Dy(NO_3)_3{\cdot}5H_2O$ as a activator and co-activator, respectively. The coprecipitated products were separated from solution, washed, and dried in a vacuum dry oven. The dried powders were then mixed with 3 wt% $B_2O_3$ as a flux and heated at $800{\sim}1400^{\circ}C$ for 3 h under the reducing ambient atmosphere of 95%Ar+$5%H_2$ gases. For the synthesized $SrAl_2O_4:Eu^{2+},Dy^{3+}$, properties of photoluminescence such as emission, excitation and decay time were examined. The emission intensity increased as the annealing temperature increased and showed a maximum peak intensity at 510 nm with a broad band from $400{\sim}650\;nm$. Monitored at 520 nm, the excitation spectrum showed a maximum peak intensity at $315{\sim}320\;nm$ wavelength with a broad band from $200{\sim}500\;nm$ wavelength. The decay time of $SrAl_2O_4:Eu^{2+},Dy^{3+}$ increased as the annealing temperature increased.