• Journal of the Korean Society of Safety
• /
• v.33 no.4
• /
• pp.46-53
• /
• 2018

This study examined the maximum resistant moment and nonlinear rotational stiffness of wedge joint between the vertical and horizontal members of system supports. To examine the maximum resistant moment and propose the nonlinear rotation stiffness of wedge joint, 6 specimens were tested and additional 3 specimens, where the horizontal member was welded to the vertical member, were tested to compare the moment capacity of wedge joints. The average maximum moment in the tested wedge joint was 1.183 kNm which represented about 70 % of the maximum moment developed in the welded specimens. And, as simulating nonlinear rotational stiffness of the wedge joint, a tri-linear model was suggested. The rotational stiffness was estimated as 23.095 kNm/rad in first stage, 7.945 kNm/rad in second stage, and 3.073 kNm/rad in third stage. For the failure mode, the specimen with the wedge joint showed the failure of joint between vertical and horizontal members. However, the specimen with welded joint represented the yielding of horizontal members.

• Journal of International Academy of Physical Therapy Research
• /
• v.7 no.2
• /
• pp.1025-1030
• /
• 2016

The purpose of this study was to investigate the effects of combined wedge on the range of motion in ankle and knee joint, ankle eversion moment and knee adduction moment, and center of pressure excursion of foot for genu varus among adult men during gait. This study was carried out with 10 adult men for genu varus in a motion analysis laboratory in J university. The subjects of the experiment were measured above 5cm width between the knees on contact of both medial malleolus of ankle while standing. The width of their knees in neutral position was measured without the inversion or eversion of the subtalar joint by the investigator. The subjects of the experiment were ten who were conducted randomly for standard insole, insole with $10^{\circ}$ lateral on rear foot wedge, insole at $10^{\circ}$lateral on rear foot and $5^{\circ}$ medial on fore foot wedge. Before and after intervention, changes on the range of motion in ankle and knee joint, ankle eversion moment and knee adduction moment, and center of pressure excursion were measured. In order to compare analyses among groups; repeated one-way ANOVA and $Scheff{\acute{e}}$ post hoc test were used. As a result, combined wedge group was significantly decreased compared to control wedge group in terms of knee varus angle in mid-stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge group in terms of ankle eversion moment in whole stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge group in terms of knee adduction moment in whole stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge in terms of center of pressure excursion in whole stance(p<.05). The results of this study suggest that combined wedge for genu varus decreased ankle eversion moment and knee adduction moment upon center of pressure excursion. We hypothesize that combined wedge may also be effective in the protection excessive ankle pronation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1994.04a
• /
• pp.19-24
• /
• 1994

Four types of horizontal joint were tested to investigate the difference with regards to the compressive behavior and strength. These include wedge-type joints (i)with and (ii)without transverse reinforcement against splitting failure of the panel concrete, and wedge-type joints (iii)with different widths of joint concrete (6cm vs 8cm) and (iv)closed platform joint. It was shown that the compressive strength of wedge-type joint is about 10% higher than that of closed-type (platform) joint. But the effect of transverse reinforcement and joint concrete widths on the strength of the joints turned out be negligible. Also, the moduli of elasticity in panel and joint are compared and the equivalent moduli of the whole wall are derived.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.64-73
• /
• 2000

The joint parts was composed of inner AL(aluminum) ring, FRP wedge and motor case which was manufactured by filament wound method. Where the motor case consists of helical and hoop layer. The finite element analysis was performed for the design variable of joint parts to improve the performance of motor case. Where the adhesive layer was modeled to elasto-perfect plastic material and the contact condition of AL ring and wedge was modeled by using the contact surface element of ABAQUS. And the sliding distance of AL ring and the hoop strain of composite case were compared to hydro-static test results to verify the accuracy of analysis results. When wedge and AL ring was perfect bonding, though the hoop strain of joint part was reduced, the maximum shear stress was occurred at the adhesive layer. Thus the adhesive layer had failed due to the high shear stress before the failure was occurred at the case. And as another design method, when wedge and AL ring was contact condition, the shear stress on adhesive layer was decreased. But the hoop stress of joint part increased due to the sliding behavior of AL ring. Finally, the fail was occurred at the composite case of joint part. The improved joint method reinforced by hoop layer to the joint parts under contact condition for wedge and Al. ring reduced the joint part's hoop strain by constraint the sliding behavior of AL ring.

• Journal of the Korea Convergence Society
• /
• v.11 no.2
• /
• pp.53-60
• /
• 2020

The purpose of this paper is to evaluate the image of the Styrofoam Wedge that can minimize the position change by supporting the wrist during the True PA and lateral examination of the wrist. In 50 people, the gap between the distal radius joint facet and the wrist bone was measured after the wrist True PA and lateral images were obtained using a general examination(vertical), tube angle(vertical:10°, lateral:20°) and Styrofoam Wedge(vertical). When joint spacing was measured in the True PA and lateral images of the wrist, general examination(5.54mm, 9.42mm), tube angle(2.05mm, 5.07mm) and Styrofoam Wedge(1.79mm, 5.46mm) were shown to be small. The smaller the joint spacing, the easier it is to observe that is open. Therefore, True PA and lateral imaging of the wrist Styrofoam Wedge can reduce the distortion of the image and thus acquire images of high diagnostic value. In addition, it may be possible to reduce the deviation caused by the change of patient's position during re-projection.

• Tunnel and Underground Space
• /
• v.29 no.5
• /
• pp.332-345
• /
• 2019

Maximum dip vector of individual joint plane, which can be uniquely defined on the hemispherical projection plane, has been established by considering its dip and dip direction. A new stereographic projection method for the rock slope analysis which employs the maximum dip vector can intuitively predict the failure modes of rock slope. Since the maximum dip vector is uniquely projected on the maximum dip point of the great circle, the sliding direction of discontinuity plane can be recognized directly. By utilizing the maximum dip vector of discontinuity both the plane sliding and toppling directions of corresponding blocks can be discerned intuitively. Especially, by allocating the area of high dip maximum dip vector which can form the flanks of sliding block the potentiality for the formation of virtual sliding block has been estimated. Also, the potentiality of forming the triangular-sectioned sliding block has been determined by considering the dip angle of joint plane the dip direction of which is nearly opposite to that of the slope face. Safety factors of the different-shaped blocks of triangular section has been estimated and compared to the safety factor of the most hazardous block of rectangular section. For the wedge analysis the direction of crossline of two intersecting joint planes, which has same attribute of the maximum dip vector, is used so that wedge failures zone can be superimposed on the stereographic projection surface in which plane and toppling failure areas are already lineated. In addition the maximum dip vector zone of wedge top face has been delineated to extract the wedge top face-forming joint planes the orientation of which provides the vital information for the analysis of mechanical behavior of wedge block.

• 대한관절경학회:학술대회논문집
• /
• 2008.04a
• /
• pp.123-124
• /
• 2008

• Journal of Korean Foot and Ankle Society
• /
• v.8 no.2
• /
• pp.142-148
• /
• 2004

Purpose: We compared the results of three surgical procedures of the old neglected Freiberg's disease that was managed with metatarsal head reshaping, metatarsal head resection, and dorsal closing wedge osteotomy. Materials and Methods: From march 1996 to July 2002, five cases in six patients whose metatarsal head collapse already progressed underwent operative treatment. We compared the operative results in the view point of the radiographic follow-up and lesser toe metatrasophalangeal joint scale of AOFAS. Results: There were no further joint destruction and loose body formation. Also, lesser toe metatrasophalangeal joint scale of AOFAS improved from average score, 38.5 (range $22{\sim}49$) of preoperative one to average score, 86.6 (range, $72{\sim}100$). Especially, the 2 cases that underwent dorsal closing wedge osteotomy showed most favorable result and the 2 cases with metatarsal resection showed next favorable result. The 2 cases with intra-articular loose body removal and metatarsal reshaping showed the least effective result among three operative methods. Conclusion: Our Operative experiences of old neglected Freiberg's disease were all satisfactory irrespective of operative options and dorsal closing wedge osteotomy was thought to be most effective method.

• Journal of Korean Foot and Ankle Society
• /
• v.9 no.1
• /
• pp.59-63
• /
• 2005

Purpose: To present the procedure and results of dorsal wedge osteotomy fixated by bioabsorbable polyglycolide pins for the treatment of symptomatic Freiberg's disease. Materials and Methods: From January 1997 to December 2002, six patients with Freiberg's disease underwent dorsal wedge osteotomy of the metatarsal neck to bring the healthy plantar part of the metatarsal head into articulation. Bioabsorbable polyglycolide pins were used for the fixation and short-leg walking cast was applied for 4 weeks. Results: All patients returned to full daily activities without pain in three months after the operation. Radiographically, solid healing of the osteotomy was observed at average ten weeks. The active range of motion of the metatarsophalangeal joint increased by a mean gain of 30 degrees, and no complication such as displacement, osteolysis or sinus formation was observed. Conclusion: Dorsal wedge osteotomy fixated by bioabsorbable pins for patients with symptomatic Freiberg's disease is effective procedure that provides relatively early range of motion exercise and avoids second procedure for implant removal.

• Journal of Korean Foot and Ankle Society
• /
• v.9 no.1
• /
• pp.87-93
• /
• 2005

Purpose: We conducted this study to examine the clinical results of the proximal metatarsal wedge osteotomy using a single screw fixation and the distal soft tissue procedure in patients with moderate to severe hallux valgus deformity. Materials and Methods: Between February 2002 and February 2004, we performed these procedures on 12 patients (15 cases). The 6 cases of all patients had mild to moderate instability in the first MTC (metatarsocuneiform) joint. We estimated the clinical outcomes, the radiological findings and complications. Results: AOFAS score was improved from preoperative 41.5 points to 87.7 points lastly on average. The mean correction angle of HVA and IMA was $23.8^{\circ}$ and $6.6^{\circ}$, respectively. The mean position of tibial sesamoid was 2.67 before surgery and 0.87 after surgery. The mean shortening of the first metatarsal bone was 3.07 mm after surgery. There was no pain and complications on the first MTC joint except the breakage of screw in one case and instability of the first MTC joint was improved postoperatively. Conclusion: We obtained good clinical and radiographic outcomes in our series. So, proximal metatarsal wedge osteotomy using a single screw fixation and distal soft tissue procedure seems one of the good surgical treatments for moderate hallux valgus deformity.