• Journal of the Korean Geotechnical Society
• /
• v.34 no.4
• /
• pp.5-11
• /
• 2018

In conventional analytical solutions for rainfall-induced soil slope stability, the Green-Ampt (1911) equation for estimating the saturation depth and the Skempton & DeLory (1957) equation for calculating the infinite slope shallow failure were compared with the numerical analysis to confirm the error. In the simple evaluation of the reason of soil slope instability due to rainfall using the conventional equations, there are many errors and, overestimation or underestimation of the calculation results. In this study, the equation consisting of the results obtained from infiltration analysis on unsaturated soil slope is proposed by applying the average range of the strength parameters of the granite weathered soils, and its reliability is verified by comparing with the numerical analysis results. The developed equation can be used easily in various fields for the estimation of slope safety factor by checking the rainfall duration and saturation depth.

• Korean Journal of Environmental Agriculture
• /
• v.17 no.1
• /
• pp.59-64
• /
• 1998

The environmental problem of the rural area has been accelerated in soil as well as water. Soil contamination is usually caused by improper operation of landfills, abandoned mine fields, accidental spills, and illegal dumpings. Once soil contamination is initiated, pollutants migrate and may cause groundwater contamination which takes much effort for remediation. Early detection, therefore, is important to prevent further contamination. Electrical resistivity method was used to detect soil contamination, but it was not effective to the heterogeneous condition. Static cone penetrometer test (CPT) has been used widely to investigate geotechnical properties of the underground. In this study, electrical resistivity method and CPT are combined to improve the applicability of it. The pilot test was performed to examine the variation of electrical resistivity with different soil minerals and pore fluid characteristics. Soil samples used were poorly graded sand, silty sandy soil, and weathered granite soil. For all the cases, electrical resistivity decreased with increasing of moisture content. Soil mineral also affected the electrical resistivity significantly. Above all, leachate addition in the pore fluid was very sensitive and caused decreasing of electrical resistivity markedly. It implies that electrical resistivity method can be applied to investigate pollutant plume effectively. This is specially sure when the sensors contact the contaminated soils directly. The CPT method involves cone penetration to the ground, therefore, underground contamination around the cone could be investigated effectively even for heterogeneous condition as it penetrates if electrical resistivity sensors are attached on the cone.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.97-105
• /
• 2004

The purpose of this study is to provide the ways of recycling of by-product limes as lightweight fill, backfill materials, and lightweight blocks by performing experimental study. New lightweight fill materials and blocks were devised by mixing by-product lime, weathered granite soil, small pieces of waste EPS, and Portland cement. Physical, geotechnical, and environmental properties of the lightweight mixed soils and blocks were analysed by laboratory experiments for mixed samples manufactured with various mixing ratios. KMS tests were also performed to evaluate the concentration variation of the chemical components of the light weight blocks leachates. It is expected that this study will contribute to resolving the problem of by-product lime disposal as well as to recycling the by-product limes as fill materials and blocks.

• The Korean Journal of Quaternary Research
• /
• v.13 no.1
• /
• pp.35-43
• /
• 1999

Goryeri archaeological site is located in the upstream valley of the Danjang River. The basement rocks of the area are composed of the Cretaceous to Palaeogene biotite granite (KbGr), acidic dyke (Kad), Milyang Andesite (Kma) and Jyunggagsan Formation. Among them Milyang Andesite and Jyunggagsan Formation are prevailed in archaeological site and they are composed of reddish brown tuffaceous shale, sandstone and conglomerate, with intercalations of acidic tuffs and lapilli tuffs. The purpose of this research is not only to compare REE pattern of the soil-sedimentary deposits with those of surrounding rocks, but also to identify vitric tephra in the soil-sedimentary deposits derived from the andesite, acidic tuff and lapilii tuff, in order to illucidate the provenance of the vitric tephra. The rare earth element(REE) of the soils and sedimentary deposits results in the same REE pattern with those analyzed from the surrounding basement rocks. This indicates that the soils and sedimentary deposits are originated from the surrounding basement rocks, most probably from the andesite and lapilli tuff. In addition, vitric tephra were identified both in the Quaternary in-situ weathered soils and sedimentary deposits (PMU-13 and PMU-17), and in the weathered surrounding lapilli tuff. These vitric tephra are considered to be different from those of Japanese AT(Aira Tanzawa) -tephra. The latter is predominant with clean, platty, bubble-walled and Y-shaped vitrics, while the former is conspicuous with those shapes of large and diverse size and devitrified, as well as having secondarily bubbled-surfaces reflecting surface weathering. The size of vitric fragments in the Goryeri site is about 300${\mu}{\textrm}{m}$ and large in size in compasion to 150${\mu}{\textrm}{m}$ of Japanese AT-Tephra. The interim results of the research are contradictary to the explanations based on a series of AT-tephra researches carried by Japanese scholar. In short, the vitric materials of the Goryeri archaeological site are most probably originated from the weathering products of the surrounding basement rocks, and are different from the AT-tephra in their size, shape and devitrification properties. Thus it is highly recommended to have a further comprehensive research which is more emphasized the magmatic genesis of these vitric tephra in addition to the external shape and morphology.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.3
• /
• pp.135-151
• /
• 1977

The present paper summerizes the studies on clay mineralogical characteristics of Korean soil, relationship between potassium and clay minerals, potassium release pattern of clay minerals and utilization of clay minerals for soil conditioner and fertilizers, which have been carried out in this laboratory. 1. The red yellow podzolic soil is mostly abundant in the upland of Korea and mainly consists of halloysite and weathered intermediates of mica such as illite and vermiculite. 2. With regard to soil parent material, kaolin mineral occurs abundant in soils derived from granite and granite gneiss. Mica is dominant in basaltic soil. The main clay mineral of the soil, originated from the Tertiary, is found montmorillonite and the volcanic soil of Jeju Island has plenty of allophane as its main clay mineral. 3. It is confirmed that the soil fertility depends on the composition of clay minerals. The red yellow podzolic soil, containing lot of kaolin, shows low productivity while the montmorillonite soil has higher productivity. 4. The release rate of solid phase potassium (micas and fixed potassium) follows the 1st order reaction equation in the equilibrium solution of $IN-NH_4OAc$. The potassium release constant is positively correlated with the mica content of the clay but negatively correlated with the content of $14.5{\AA}$ minerals. On the other hand, the potassium release constant has very high correlation with the ratio(Kex/Kt) of exchangeable potassium(Kex) to total potassium(Kt). 5. It is also found that Kex/Kt has rather high correlation with the content of mica and $14.5{\AA}$ minerals existed in the clay as well as the mica content of the soil.

• Korean Journal of Soil Science and Fertilizer
• /
• v.6 no.1
• /
• pp.1-8
• /
• 1973

This study examined the morphological, physical and chemical characteristics of the Yesan and the Songjeong series derived from residuum of the granite developed on gently sloping to rolling relief in Honam reclamable land Area. The results of this study are summarized as follows. 1. The morphological characteristics. In the Yesan series, the surface soils(Ap horizons) are brown to dark brown sandy loam. The subsoils(B horizons) are yellowish red to red sandy clay loam to sandy loam and the soil profile development is weak. The Songjeong series, the surface soils (Ap horizons) are washed by erosion, so the subsoils are revealed on the surface, and these are dark red silty clay loam. The subsoils (B horizons) are red silty clay loam and thin clay cutans are formed on the ped faces of the structure. The substrata of two soil series are deeply weathered granitic saprolite. 2. The physical and chemical characteristics. The distribution of clay content tends to increase from surfaces to subsoils with depth gradually. On the Yesan series, the content of clay is less than 18%, soil pH (6.0 in the surface-soil, 4.5-5.0 in the subsoil), the content of organic matter (1.8% in the surface soil, 0.1~0.4% in the subsoil), available phosphate (40 ppm), the cation exchange capacity(4~8 me/100 gr) are very low, and the base saturation (57.8% in the surface soil, 46.3% in the subsoil) is moderate. On the Songjeong series, the content of clay is 30~40%, pH (5.7-6.0), the content of in organic matter (1.25% in the surface soil, 0.1~0.4% in the subsoil), available phosphate(4 ppm), the cation exchange capacity(6.2 me/100 gr in the surface soil, 2~6 me/100gr in the subsoil) are very low, and the base saturation(28.1% in the surfacesoil, 16~23% in the subsoil) is also low. 3. The Yesan and Songjeong series are for med under a temperate humid climate, and classified as Red Yellow Soils in the old classification system. According to U.S.D.A. 7th approximation the former belongs to Typic Dystrochrepts in Inceptisols, and the latter, Typic Hapludults in Ultisols.

• Journal of Korean Society of Forest Science
• /
• v.79 no.4
• /
• pp.376-387
• /
• 1990

A research effort has been made to determine soil buffer capacity in forest soils nearby urban and industrialized regions. Buffer capacities of soils from four regions were measured by different pH levels of artificial acid precipitation. The following conclusions have been drawn in response to the overall research objectives. Soil Suffer capacity was the highest in Kangwondo followed by Uisan, Yeochon and Seoul when simulated acid precipitation were treated at the level of pH 3.0-5.7. With the acid precipitation treatment below pH 2.0 level, however, the capacity dropped seriously with no significant differences between the regions. In Kangwondo region soils weathered from granite and limestone showed significant differences in the buffer capacities. Soil collected in Seoul and Ulsean revealed that the capacities tended to increase with the distance from the pollution sources when treated at pH 3.0, 4.5 and 5.7 level of acid precipitation. The major mechanism of soil buffer observed during simulated acid precipitation experiment was canon exchange for Kangwondo forest soils. In Seoul region canon exchange also played an important role in soil buffering under artificial acid precipitation between 3.0 and 5.7 pH levels, yet under pH 2.0 level aluminum and silicate hydrolysis. In Ulsan canon exchange was a msjor determinant for the buffer capacity above pH 4.5 level, between pH 3.0-4.5 aluminum hydrolysis and below pH 3.0 aluminum and silicate hydrolysis. In Yeochon silicate hydrolysis led buffer capacity above pH 4.5 and below pH 4.5 aluminum hydrolysis.

• The Journal of Engineering Geology
• /
• v.27 no.4
• /
• pp.475-487
• /
• 2017

We performed landslide flume tests to analyze characteristics of landslide occurrence and change in the ground materials due to rainfall infiltration. The test apparatus is composed of flume, rainfall simulator, and measurement sensors and landslides were triggered by heavy rainfall (Intensity=200 mm/hr) sprinkled at the above of an artificial slope. The measurement sensors for matric suction and volumetric water content were installed with 3 sets at shallow (GL-0.2 m), middle (GL-0.4 m), and deep depth (GL-0.6 m) in the slope and the tests were performed with in-situ, loose, and dense condition of each weathered soils of granite, gneiss, and mudstone. The analyses show that surface erosion was dominant in initial time of the test due to heavy rainfall and then landslides occur following locally happened transverse tension cracks. The characteristics of landslide were both shallow failure because of a spread of wetting front induced by the rainfall infiltration and retrogressive failure. While the matric suction was decreased rapidly without any precursor in the soil saturation, the volumetric water content was increased gradually, reached its maximum value, and then decreased rapidly with landslide.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.8
• /
• pp.768-774
• /
• 2008

To evaluate the effect of the solidified/stabilized sewage sludge on landfill sites, lysimeter tests were conducted. Lysimeters (LR1, LR2, and LR3) were filled with the material(Compost : Fodder : Sand = 10 : 10 : 80) and covered with different types of the cover soils, the G solidified sludge produced from the neutral solidifying chemical agent(LR1), the A solidified sludge produced from the alkali solidifying chemical agent(LR2), and the weathered granite soil(LR3). Those lysimeters were kept at the temperature controlled room with 30 $\pm$ 2$^{\circ}C$ for about 450 days. As the results, it was appeared LR2 > LR1 > LR3 that total gas production rate(L), gas production rate(L/VS(kg)) and cumulative gas(CO$_2$ + CH$_4$) production. There were not significant differences at decrease of the COD$_{Cr}$ in the leachate from LR1 and LR3. Thus, it had been shown that the use of the G solidified sludge as cover soil did not affect the COD$_{Cr}$ in the leachate. The COD$_{Cr}$ from LR2 had been increased since around 250 days because solidified/stabilized sewage sludge became re-slurry. T-N and T-P from LR3 also were higher than LR1 and LR2. Also were, the use of the solidified/stabilized sewage sludge as a cover soil, therefore, did not affect the T-N and T-Pconcentrations in the leachate.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.3
• /
• pp.323-345
• /
• 2019

It is essential to predict ground conditions ahead of a tunnel face in order to successfully excavate tunnels using a shield TBM. This study proposes a forward prediction method for a mixed soil ground and/or a ground containing core stones by using electrical resistivity and induced polarization exploration. Soil conditioning in EPB shield TBM is dependent upon the composition of mixed soils; a special care need to be taken when excavating the core-stoned soil ground using TBM. The resistivity and chargeability are assumed to be measured with four electrodes at the tunnel face, whenever the excavation is stopped to assemble one ring of a segment lining. Firstly, the mixed ground consisting of weathered granite soil, sand, and clay was modeled in laboratory-scale experiments. Experimental results show that the measured electrical resistivity considerably coincides with the analytical solution. On the other hand, the induced polarization has either same or opposite trend with the measured resistivity depending on the mixed ground conditions. Based on these experimental results, a method to predict the mixed soil ground that can be used during TBM tunnel driving is suggested. Secondly, tunnel excavation from a homogeneous ground to a ground containing core stones was modeled in laboratory scale; the irregularity of the core stones contained in the soil layer was modeled through random number generation scheme. Experimental results show that as the TBM approaches the ground that contains core stones, the electrical resistivity increases and the induced polarization fluctuates.