• 태양에너지
• /
• 제13권2_3호
• /
• pp.45-52
• /
• 1993

현열저장에서 열성층의 이점을 태양열 주택에 적용해보았다. 성층으로 인하여 에너지 입력의 열이용 효율이 증가되는 효과가 논의되었고, 실험과 시뮤레이션을 통하여 설명되었다. 성층을 촉진시키기 위하여 Distributor를 사용하였으며, 본 실험에서 Q=8 liter/min, ${\Delta}T=40^{\circ}C$일 때, 최대 90%의 열이용 효율을 얻을 수 있었다. 한편 성층을 촉진시키기 위하여 Distributor의 적은 구멍에서 나오는 유동(속도와 압력)이 같게 제작할 수만 있다면 그 이상의 열이용효율도 얻을 수 있음이 입증되었다.

• 한국태양에너지학회 논문집
• /
• 제21권4호
• /
• pp.37-46
• /
• 2001

This study describes the experimental study that focuses on the effects that distributor shapes and flow rate variations have an influence on the stratification in a rectangular thermal storage tank. Experiments were carried out under the conditions that the flow rates of working fluid are 20, 10 and $5\ell$/min. The storage tank is initially filled with chilled water of $1^{\circ}C$, and is extracted through the bottom at the same rate as the return warm water from load is entered through the distributor at the top of the tank. The thermo-cline forms at the top of the storage tank as the warm water enters the tank from the load through the distributor and the thermo-cline thickness increases with time. Emphasis is given to the effects of mixing at the inlet that increases the thermo-cline decay Flow rate variation and inlet distributor shapes are the important parameters in deciding the performance of a storage system. Stratification degree increases with decreasing in inlet flow rate under $10\ell$/min. Experiments shows that better thermal stratification can be obtain using the distributor to limit momentum mixing at the inlets and outlets. Also, 12% of improvement in the thermal energy usage has been achieved using the modified distributor discharging same flow rate in each lateral ports.

• 한국태양에너지학회 논문집
• /
• 제27권4호
• /
• pp.43-49
• /
• 2007

This study is conducted to improve the efficiency of a thermal storage tank. The thermal storage tank was designed to store heat energy that obtained from the solar or the others heat sources. However, it has difficulties in storing heat with nonuniform temperature through the entire tank with respect to the vertical direction, This study is focused on the thermal stratification to improve thermal comfort for the resident in house. To enhance temperature stratification of the tank, a distributor was designed and installed in the middle of the storage tank vertically. The vertically designed distributor could supply the return water with stratified temperature in the storage tank with respect to the height. The water velocity from the distributor hole is the same with the other outlet in the distributor. However, gravity effect on the flow in the storage tank is much higher than that of the velocity effect due to that Froude Number is less than 1. During the heat charging process in the storage tank, temperature maintained with little difference with respect to the height. However the charging process takes long time to get a effective temperature for the heating or hot water supply because of all of water in the storage tank needs to be heated.

• 태양에너지
• /
• 제10권3호
• /
• pp.3-12
• /
• 1990

본 실험연구에서는 탱크의 직경에 대한 높이의 비(H/D)가 3이고 유입 유량이 8LPM, 유입수의 온도와 기존 저장수와의 온도차, ${\Delta}T=30^{\circ}C$일때, 운동량교환을 최소화하여 가장 좋은 성층을 얻었고 또한 실험에서 사용한 유입구(Inlet Port)의 경우 수정 Richardson수(Modified Richardson Number), Ri가 0.004(Q=10LPM, ${\Delta}T=30^{\circ}C$) 이하의 값에서는 완전 혼합(Fully Mixing)이 발생하고 H/D가 작아질수록 혼합층의 두께($H^*/H$)가 증가하여 성층 축열에는 바람직하지 못하였다. 그리고 성층은 성층을 촉진시키기 위하여 Distributor를 사용했을 때가, Distributor를 사용하지 않은 유입구(Inlet Port)의 경우 보다 잘 형성되어 저장효율이 Distributor를 사용한 경우(Q=8LPM, ${\Delta}T=30^{\circ}C$, H/D=3)에 Distributor를 사용하지 않은 유입구(Inlet Port)의 최저효율 63%(Q=12LPM, ${\Delta}T=30^{\circ}C$, H/D=3인 경우)보다는 31% 정도, 최대효율 84%(Q=8LPM, ${\Delta}T=30^{\circ}C$, H/D=3인 경우)보다는 11% 정도 높은 95%까지 저장 효율을 증가시킬 수 있었다. 더 나아가서 단면이 균일한 원형 Distributor(A=D=Constant)의 경우에, 유량이 8LPM인 경우에 관내의 압력차가 작아 부분혼합(Partial Mixing)이 감소하여 안정된 성층을 얻을 수 있었다. 그리고, Distributor의 직경을 다음식과 같이 $$\frac{D}{D_L}=(\frac{x}{L})^{1/2}(1+\frac{fL}{2D})-\frac{fx}{2D_L}$$ 길이에 대하여 변화시켜 Distributor를 제작함으로써, 보다 안정된 열성층과 높은 열저장 효율을 얻을 수 있을 것으로 예상한다.

• 한국수산과학회지
• /
• 제36권3호
• /
• pp.254-262
• /
• 2003

Effect of the air distributor pore size for the removal of aquacultural waste, such as protein, total suspended solids (TSS), chemical oxygen demand (COD), turbidity and total ammonia nitrogen (TAN) from sea water was investigated by using foam separator. With the increase of pore size of air distributor, removal rates and efficiency of protein decreased. Removal rate by commercial air stone was in the range between the removal rates by G2 and G4 sintered glass discs. Within the range of pore size distributor from Gl to G4, the removal efficiency of protein were ranged from 21 to $42\%.$ The changes of removal rates and efficiencies of TSS, COD and turbidity were similar to proteins. TAN was removed by stripping. The pore size of air distributor for a higher overall oxygen mass transfer coefficient and saturation efficiency provided the condition for higher protein removal rate. Also the foam separator could be used as an aerator.

• 설비공학논문집
• /
• 제19권3호
• /
• pp.269-274
• /
• 2007

A 3-way valve has been applied to a distributor in a hot-water heating system and the performance of the system was evaluated in view of the variations of pressure drop and flow rate. The 3-way valve has been designed to bypass overplus hot-water when a control valve is closed. Note that the flow goes through heating pipeline in normal operation. In the present study, the measured pressure drops in each part of the flow paths show that the contribution to the total pressure drop is in the order of the supply header with control valves, piping system of each room and return header of the distributor, even though the amount of it is different according to the flow paths. As a result of performance test by sequential closing of the control valves, the variations of pressure drop and flow rate in the distributor with 3-way valves is much lower than those with previous 2-way valves, which prevent noises induced by pressure fluctuations.

• 설비공학논문집
• /
• 제14권6호
• /
• pp.503-511
• /
• 2002

Heat flow characteristics during hot water extraction process was studied experimentally. Data were taken at various outlet port type for the fixed inlet port type, inlet-outlet temperature differences and mass flow rates. In this study, the temperature distribution in a storage tank and an outlet temperature were measured to predict a degree of stratification in the storage tank, and a useful rate of hot water was analysed with respect to the variables dominating a extraction process. Experimental results show that the degree of stratification and useful rate of hot water are all high in a low flow rate in case of using modified distributor I (MDI) as the outlet port type.

• 설비공학논문집
• /
• 제19권8호
• /
• pp.577-584
• /
• 2007

A variable-flow-rate balancing valve has been developed and optimized to apply to a distributor in a hot-water heating system. Fluid dynamic performance of the system was evaluated by comparing the results with the previous pressure difference control valve (PDCV) system. In view of the variations of pressure drop and flow rate according to the sequential closing of the control valves, the present system which is named "smart system distributor", is very stable without a certain flow rate concentration. The level of pressure drop variation is also low as compared with the previous system with a PDCV. In view of the occurrence of cavitation, the present system is quite superior to the previous system because the instantaneous pressures at all sections are much higher than the vapor pressure. On the other hand, the previous system has a possibility of cavitation when one or more control valves are closed.

• 설비공학논문집
• /
• 제13권7호
• /
• pp.549-556
• /
• 2001

Heat flow characteristics during hot water extraction process was studied experimentally. Data were taken at various outlet port type for the fixed inlet port type, inlet-outlet temperature differences and mass flow rates. In this study, the temperature distribution in a storage tank and an outlet temperature were measured to predict a flow pattern in the storage tank, and a hot water extraction efficiency was analysed with respect to the variables dominating a extraction process. Experimental results show that the extraction efficiency is high in a low flow rate in case of using modified distributor I(MDI) as a outlet port type.

• 한국수소및신에너지학회논문집
• /
• 제24권5호
• /
• pp.444-450
• /
• 2013

The distribution performance of refrigerant distributors in air conditioner evaporators was examined numerically and experimentally. Internal flow analysis of the distributor by CFD found that the distance from the socket to the cone, the angle of the cone and the base area of the cone were the most important factors affecting refrigerant distribution ability and vortex creation. To enhance distribution performance, two distributors with improved internal structures were designed. To test these new structures, distribution performance was also analyzed by CFD and an empirical experiment was carried out using the water-nitrogen. Experimental results on the distribution fraction of each distributor hole showed a good agreement with the results of the CFD analysis. Thus, the new design of the distributors enhanced distribution performance of the refrigerant distributors.