• Clean Technology
• /
• v.15 no.1
• /
• pp.54-59
• /
• 2009

In this study, the separation of water/bitumen emulsion was investigated by chemical demulsification method. Motor oils (GS Caltex Deluxe Gold V 7.5W/30, Hyundai gear oil 85W/140) and asphalt (AP-5, KS M 2201, Dongnam Petrochemical MFG. Co.) were used as model oils in the preliminary experiments to effectively remove water from water/bitumen emulsion. The bitumen extracted from Canadian oilsands was used in this study. The water/oil emulsion was not separated without demulsifiers, and Hyundai motor oil showed higher efficiency of water separation at a low concentration of demulsifier compared with that for GS Caltex motor oil. However, as the concentration increased, the efficiency did not rapidly increase compared with that of GS Caltex motor oil. It was highly speculated that the water phase of Hyundai motor oil was not dispersed well compared with that of GS Caltex motor oil because the viscosity of Hyundai motor oil was much higher than that of GS Caltex motor oil. The demulsifier of higher HLB (hydrophilic - lipophilic balance) value had high separation efficiencies in water/oil emulsion. The TWEEN 20 (polyoxyethylene sorbitan monolaurate solution) showed better separation efficiency than other demulsifiers.

• Journal of the Korean earth science society
• /
• v.44 no.4
• /
• pp.291-306
• /
• 2023

Shallow groundwater in rural areas is primarily polluted by agricultural activities. Nitrate-nitrogen is an indicator of artificial pollution. In this study, the hydrochemical characteristics and nitrate-nitrogen pollution of shallow groundwater were examined in two agricultural villages (Hyogyo-ri and Sinan-ri) in Chungcheongnam-do Province, Korea. Physicochemical quality analysis of shallow groundwater and stream water in the field, and chemical analysis in the laboratory were conducted from July 2020 to October 2021. In Hygyo-ri and Sinan-ri villages, shallow groundwater mainly belonged to the Ca-Cl, Ca-H CO₃, Na-HCO₃, and Na-Cl types, whereas stream water predominantly belonged to the Ca-HCO₃ type. The nitrate-nitrogen concentration in shallow groundwater varied depending on the season, displaying an increased concentration of nitrate-nitrogen in the dry season compared to the rainy season. Stream water may be influenced by runoff into villages from the surrounding area, although both shallow groundwater and stream water are affected by artificial pollution. In addition, the nitrate-nitrogen concentration in stream water was lower than that in shallow groundwater.

• Journal of Applied Biological Chemistry
• /
• v.48 no.4
• /
• pp.213-217
• /
• 2005

Microbial hydrogel was prepared with poly(${\gamma}$-glutamic acid) produced from Bacillus subtilis BS62 using crosslinking reagent, ethylene glycol diglycidyl ether (EGDE), and its physico-chemical characteristics were examined. Hydrogel which prepared from 10 grams of 10% PGA solution with $600\;{\mu}l$ of EGDE at $50^{\circ}C$ for 17 h swelled 4,320 times its dry weight, and time to reach swelling equilibrium in deionized water at 4 to $45^{\circ}C$ range was about 20 h. Swollen hydrogel shrunk in ionic solutions, and rate of shrinkage was higher in calcium chloride solution than sodium chloride solution. Swelling rate of hydrogel increased 1.3-fold of initial swelling rate for 30 min at $80^{\circ}C$.

• Macromolecular Research
• /
• v.10 no.2
• /
• pp.127-134
• /
• 2002

Microporous polypropylene hollow fiber membrane was fabricated from isotactic polypropylene-soybean oil system by melt spinning process. Addition of nucleating agent accelerated the crystallization rate and elevated the crystallization temperature. Nucleating agent increased the number of nuclei and spherulites, which offered more inter-spherulitic amorphous sites for stretching. Benzoic acid, adipic acid, and dibenzylidene sorbitol were selected as nucleating agents, and their characteristics and effects were investigated by thermal and optical analyses. Spherulite growth and micropore formation characteristics were correlated with the kind of nucleating agent. Benzoic acid and adipic acid showed the remarkable nucleating effect, while dibenzylidene sorbitol was less effective than those. Nucleating agents also helped the sample have uniform microporous structure. Increase of nucleating agent composition enhanced the nucleation effect to some extent. Nucleating agents played very important roles in enhancing the membrane porosity and water flux.

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.147-153
• /
• 1990

Poly(hydroxypropyl methacrylate) membranes and matrix devices having tertiary amine moiety were prepared by sintering method, and their permeation characteristics were investigated. The water content of this membrane was increased with decreasing the pH of the medium. The permeability of this membrane was increased with decreasing the sintering pressure. Using sintered matrix device 'burst effect' was found at the early stage, and initial insulin release of glucose oxidase immobilized matrix device could be controlled by glucose concentration of the solution.

• Journal of the East Asian Society of Dietary Life
• /
• v.14 no.5
• /
• pp.457-462
• /
• 2004

Physical properties of soybean curd powder prepared with hot air, vacuum and freeze drying methods were investigated. Adsorption characteristics were studied under various water activities (such as 0.11, 0.33, 0.44, 0.55, 0.66, 0.75, 0.85, and 0.93) at 5℃, and prediction models were developed. Equilibrium moisture and monolayer moisture contents were the highest when freeze dried. due to the porous structure. In this result, Oswin model was the best fit for the isotherm of soybean curd. Sorption enthalpy indicated that high moisture content of powder showed lower sorption than that of low moisture content.

• Membrane Journal
• /
• v.26 no.2
• /
• pp.116-125
• /
• 2016

This study described a synthesis of MF having a arsenic removal characteristics and the fundamental research was performed about the simultaneous removal system of both As(III) and As(V) ions with the composite nanofiber membrane (PMF) based on PVdF and MF materials for the water-treatment application. From the TEM analysis, the shape and structure of MF materials was investigated. The mechanical strength, pore-size, contact angle and water-flux analysis for the PMF was performed to investigate the possibility of utilizing as a water treatment membrane. From these results, the PMF11 showed the highest value of mechanical strength ($232.7kgf/cm^2$) and the pore-diameter of composite membrane was reduced by introducing the MF materials. In particular, their pore diameter decreased with an increase of iron oxide composition ratio. The water flux value of PMF was improved about 10 to 60% compared with that of neat PVdF nanofiber membranes. From the arsenic removal characterization of prepared MF materials and PMF, it was shown the simultaneous removal characteristics of both As(III) and (V) ions, and the MF01, in particular, showed the highest adsorption-removal rate of 93% As(III) and 68% As(V), respectively. From these results, prepared MF materials and PMF have shown a great potential to be utilized for the fundamental study to improve the functionality of water treatment membrane.

• Tribology and Lubricants
• /
• v.37 no.5
• /
• pp.189-194
• /
• 2021

A straightforward, yet effective surface modification method of stainless steel mesh and its interesting anti-wetting characteristics are reported in this study. The stainless steel mesh is electrochemically etched, and the specimen has both micro and nano-scale structures on its surface. This process transforms the two types of mesh specimens known as the regular and dense specimens into hydrophobic specimens without applying any hydrophobic chemical coating process. The fundamental wettability of the modified mesh is analyzed through a dedicatedly designed experiment to investigate the waterproof characteristics, for instance, the penetration threshold. The waterproof characteristics are evaluated in a manner that the modified mesh resists as high as approximately 2.7 times the pressure compared with the bare mesh, i.e., the non-modified mesh. The results show that the penetration threshold depends primarily on the advancing contact angles, and the penetration stop behaviors are affected by the contact angle hysteresis on the surfaces. The findings further confirm that the inexpensive waterproof meshes created using the proposed straightforward electrochemical etching process are effective and can be adapted along with appropriate designs for various practical applications, such as underwater devices, passive valves, and transducers. In general, , additional chemical coatings are applied using hydrophobic materials on the surfaces for the applications that require water-repelling capabilities. Although these chemical coatings can often cause aging, the process proposed in this study is not only cost-effective, but also durable implying that it does not lose its waterproof properties over time.

• Journal of the Korea Concrete Institute
• /
• v.11 no.4
• /
• pp.21-29
• /
• 1999

In this study, an experiment was performed to analyze the influence of water-cement ratio on the fundamental characteristics of antiwashout underwater concrete using blended sand (sea sand:river sand = 1:1). The water-cement ratio (45%, 50%, 55%, 60%), andtiwashout underwater agent contents (0.82%, 1.00%, 1.14% of water contents per unit volume of concrete), and superplasticizer contents (1.5%, 2.0%, 2.5% of cement contents per unit volume of concrete) were chosen as the experimental parameters. The experimental results show that the underwater segregation resistance, unit weight of hardening concrete and compressive strength were increased as the water-cement ratio decreased and as the antiwashout underwater agent contents increased. On the other hand, the flowability(slump flow) was increased to the 55% of the increase of water-cement ratio, however, it was decreased at the ratio of 60%. From this study, the antiwashout underwater concrete can potentially be used as a materials underwater work of ocean if the water-cement ratio and chemical admixture contents for the suitable balance between cost and performance are properly selected.

• Journal of Korean Society on Water Environment
• /
• v.39 no.6
• /
• pp.465-474
• /
• 2023

The chemical composition and molecular weight characteristics of dissolved organic matter (DOM) exert a profound influence on the efficiency of organic matter removal in water treatment systems, acting as efficiency predictive indicators. This research evaluated the primary chemical and molecular weight properties of DOM derived from diverse sources, including rivers, lakes, and biomasses, and assessed their relationship with the efficiency of coagulation/flocculation treatments. Dissolved organic carbon (DOC) removal efficiency through coagulation/flocculation exhibited significant correlations with DOM's hydrophobic distribution, the ratio of humic-like to protein-like fluorescence, and the molecular weight associated with humic substances (HS). These findings suggest that the DOC removal rate in coagulation/flocculation processes is enhanced by a higher presence of HS in DOM, an increased influence of externally sourced DOM, and more presence of high molecular weight compounds. The results of this study further posit that the efficacy of water treatment processes can be more accurately predicted when considering multiple DOM characteristics rather than relying on a singular trait. Based on major results from this study, a predictive model for DOC removal efficiency by coagulation/flocculation was formulated as: 24.3 - 7.83 × (fluorescence index) + 0.089 × (hydrophilic distribution) + 0.102 × (HS molecular weight). This proposed model, coupled with supplementary monitoring of influent organic matter, has the potential to enhance the design and predictive accuracy for coagulation/flocculation treatments targeting DOC removal in future applications.