• Textile Coloration and Finishing
• /
• v.24 no.3
• /
• pp.173-179
• /
• 2012

Silk fabric treated with fluorocarbon resins (Asahi Guard AG-7005 and AG-E061) were washed and subsequently heat treated varying the washing cycles and the temperature. After the processing, the water and oil repellencies, and contact angle to water were evaluated. The water and oil repellencies decreased by the washing and recovered by following heat treatment. Also ESCA measurement was carried out to investigate the surface chemical composition of the treated fiber. The $F_1s$ intensity of the treated fabric decreased by the washing and recovered by the subsequent heat treatment. On the other hand, the $O_1s$ intensity increased by the washing and decreased by following heat treatment. From the results, it is clear that change of the water and oil repellencies of the silk fabric treated with fluorocarbon resin occurred by the washing and subsequent heat treatment. Considering a change of the water repellency of the silk fabric treated with fluorocarbon resin, it seems likely that the fluoroalkyl group of the fluorocarbon resin rotates from surface to inside of the fiber by the washing to adapt to the hydrophilic circumstance, and the orientation of the fluoroalkyl groups of the resin disturbed by the washing recovers the orientation to the fiber surface after the subsequent heat treatment.

• Textile Coloration and Finishing
• /
• v.20 no.6
• /
• pp.87-91
• /
• 2008

It is commonly known that water repellency of the fabric treated with fluorocarbon resin brings about a decrease by the washing and recovers by the subsequent heat treatment. In this article, effect of the water repellency was investigated on the nylon 6, triacetate and silk fabrics treated with hydrocarbon and silicon resins. Hydrocarbon and silicon resins have been widely used in the textile finishing as the softening and water proofing agents. The fabrics were treated with hydrocarbon resins, Paragium JQ and RC (Ohara Paragium Chemical Co.) and a silicon resin, Poron MR (Shinetsu Chemical Co.), and then washed and subsequently heat treated. Although the water repellency increased by the resin treatment, it decreased by the washing apparently and recovered a little by the heat treatment. The effect of the heat treatment was small comparing with that of the fluorocarbon resin. Furthermore, as a mechanical property of the treated fabric, KES shearing and bending hysteresis parameters, modulus and hysteresis width of the hydrocarbon resin-treated nylon 6, triacetate and silk fabrics decreased by the heat treatment after washing. Therefore, the treatment is effective at improving the softening of the fabric in water repellent finish.

• Journal of Powder Materials
• /
• v.10 no.5
• /
• pp.344-347
• /
• 2003

Pure tantalum powder has been produced by combining Na as a reducing agent, $K_2$TaF$_{7}$ as feed material, KCl and KF as a diluent in a stainless steel (SUS) bomb, using the method of metallothermic reduction. And we examined various types of after-treatment that affect the high purification of powder. A significant amount of impurities contained in recovered powder was removed in various conditions of acid washing. In particular, 20% (HCl + HNO$_3$) was effective in removing heavy metal impurities such as Fe, Cr and Ni, 8% H$_2$SO$_4$ + 8% $Al_2$(SO$_4$)$_3$ in removing fluorides such as K and F from non-reactive feed material, and 2% $H_2O$$_2$ + 1 % HF in removing oxides that formed during reaction. Significant amounts of oxygen and part of light metal impurities could be removed through deoxidation and heat treatment process. On the other hand, because it is difficult to remove completely heavy metal impurities such as Fe, Cr, and Ni through acid washing or heat treatment process if their contents are too high, it is considered desirable to inhibit these impurities from being mixed during the reduction process as much as possible.

• Textile Coloration and Finishing
• /
• v.13 no.3
• /
• pp.180-187
• /
• 2001

Generally, polyester microfiber has much greater dye uptake than that of regular ones. In spite of high dye up-take visual shade depth of dyed fabric decreases with smaller denier, which results in poor washing fastness of dyed fabric. In this study, in order to investigate the washing fastness, polyester microfiber fabric was dyed by using two type of disperse dyes and treated with 3 different reduction clearing methods. The reduction clearing methods in this study are normal alkaline reduction clearing, $N_2$ gas replacement method, and ultrasonic treatment during reduction clearing. The results were as followings ; The most important factors affecting the washing fastness of polyester artificial suede fabric were found to be the reduction clearing method, the chemical structure of used disperse dyes and the structure and denier of fibers. It was also obtained that the heat treatment of dyed fabric decreased the washing fastness due to the dye migration from inner phase to surface.

• Textile Coloration and Finishing
• /
• v.31 no.4
• /
• pp.225-232
• /
• 2019

The colorants of kale powders were optimally extracted using an 1:1 mixture solvent of ethanol and DMSO at 105℃ for 30 minutes obtaining a high yield of 359.7㎍/mL chlorophylls. Low color fastness of the dyed fabrics with the extracts, particularly against washing and solar radiation, can be overcome by the combined treatments of chitosan, heat setting and tannic acid. Washing fastness to color change was improved from rating 1-2 up to 5 due to the enhanced electrostatic interactions between the colorants and the positive glucosamine unit of the chitosan in the cationized cotton. In addition, the tannic acid treatment contributed to the additional increase in color fastness after the sequential treatments of chitosan pretreatment, dyeing and heat setting.

• Journal of Korea Foundry Society
• /
• v.28 no.5
• /
• pp.237-241
• /
• 2008

This study has been carried out to investigate the wear and heat resistant properties of durable moldwash agent for Al gravity casting according to mold washing process conditions. The wear properties of coated specimen were performed by sliding wear testing machine and heat resistance were evaluated by measuring the loss of coated moldwash agent during emerging of coated specimen in Al melts. During testing, experimental variables were mold surface temperature, moldwash agent/distilled wear, and additive concentrations. The lower additive concentration and mold temperature caused the smooth surface roughness of coated specimen, It was found that the specimen coated with moldwash/water ratio 1:3, additive concentration 9wt% and mold temperature higher than $200^{\circ}C$ showed superior wear and heat treatment. Also, these results were supported by fluidity test.

• Journal of Bio-Environment Control
• /
• v.21 no.4
• /
• pp.411-418
• /
• 2012

This study was conducted to investigate the effect of calcinated calcium (CC) alone or combination with heat treatment on storage quality and microbial growth in fresh-cut broccoli. Fresh broccoli samples were cut into small pieces and washed in normal tap water (TW), $50{\mu}L{\cdot}L^{-1}$ chlorinated water (pH 6.5), $1.5g{\cdot}L^{-1}$ CC, heat treatment in TW at $45^{\circ}C$, and CC dissolved in TW at $45^{\circ}C$ for 2 minutes separately. Samples were then packaged in $50{\mu}m$ polyethylene bags and stored at $5^{\circ}C$. Results revealed that like $50{\mu}L{\cdot}L^{-1}$ chlorine, washing in CC at normal water temperature was effective in reducing microbial population in fresh-cut broccoli samples. Washing with CC combined with heat treatment increased an electrical conductivity of fresh-cut broccoli. Combined heat treatments with TW and CC reduced aerobic plate count on fresh-cut broccoli, only in initial period of storage. But, later on heat treatment induced injury of fresh-cut broccoli resulting more microbial population compared to non heat treatment. However, samples treated with CC alone had good quality with low off-odor at the end of storage. Results suggest that CC, an environment-friendly sanitizer could be an alternative to chlorinated water for washing of fresh-cut broccoli without affecting sensorial quality.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.5
• /
• pp.262-269
• /
• 2006

The development of eco-friendly low pressure carburizing system with high pressure gas quenching(LPC-GQ, 500kg/charge) led to new stage in the fundamental case-hardening treatments. This is due to its ability to provide tighter tolerances on the carburizing process with notable reductions in distortion of the carburized and hardened workpiece. This system is characteristics by high uniformity and reproducibility of heat treatment results, absence of an intergranular oxidation layer, carburizing of complex shapes, reduced cycle time, low operating costs, simplified production, eliminate post washing, and reduced grinding costs.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.5
• /
• pp.612-617
• /
• 2009

Fresh vegetable juice is a non-heat treated product and the only step to reduce microbial growth is washing. Therefore, the materials for fresh vegetable juice including Angelica keiskei, Brassica loeracea var. acephala, and Daucus carota L. were treated by ozone after the first washing process and investigated for microbial and chemical changes. The number of the total aerobic bacteria in materials after selection step were $8.2{\times}10^5{\sim}5.0{\times}10^6\;CFU/g$, which was a higher contamination level than the limit of Korea food code ($10^5\;CFU/g$). However, after the 1st washing process and ozone treatment, the total aerobic bacterial number was reduced to $4.7{\times}10^4{\sim}6.7{\times}10^4\;CFU/g$, which showed 2 log microbial reduction. After the 2nd washing step followed by ozone treatment, there was no difference in microbial number. The number of colifroms in the materials of fresh vegetable juice were $8.0{\times}10^3{\sim}3.5{\times}10^3\;CFU/g$ initially but showed $1.5{\times}10^2{\sim}3.0{\times}10^2\;CFU/g$ after the ozone treatment (1 log reduction). On the other hand, there was no changes in the contents of ascorbic acid, flavonoids, polyphenols, minerals (cadmium and lead) during all processes. In addition, no color changes were observed during washing process. Therefore, ozone treatment in the materials of fresh vegetable juice decreased the microbial numbers. Also, chemical characteristics of ozone treated sample were not different when compared with control.

• Journal of Fashion Business
• /
• v.15 no.5
• /
• pp.43-54
• /
• 2011

Digital Textile Printing(DTP) is appropriate for quick response system(QRS) and is closely connected with high value added fashion industry. Fashion products of high price are mainly silk and cotton. For high quality DTP products, it is important to optimize the parameters of media, pre and after-treatment, ink, printer, etc. DTP for these two fiber materials is also accompanied certainly with steaming as after-treatment process for coloration. Role of steam is like water in exhaustion dyeing. Steam can diffuse dye or ink in printing paste to fiber. Quality of DTP products depend on after-treatment processes such as steaming, washing, drying. Current production amount of DTP is smaller than one of conventional textile printing. However conventional after-treatment system has been using so far. This is mismatched with DTP in terms of process efficiency, spot work of small lot, quality control. In this study, continuous after-treatment system has been suitably designed for DTP that washing and drying are available after steaming. So, It is possible to improve efficiency of DTP process. Especially, the effects of after-treatment process, such as temperature of heat drum, steaming time on printability, color difference, color fastness were examined. Two types of samples(cotton knit and silk fabrics) were used. The results were obtained as follows : First, there is no a wide difference between the K/S values of cotton and silk treated with continuous after-treatment system and those of sample treated with conventional printing after-treatment method. So it is more effective to use the continuous after-treatment system than conventional printing after-treatment system in case of the daily throughput of 1,000 yards below. Second, after continuous after-treatment for DTP, K/S values were increased and lightness($L^*$) values were decreased. ${\Delta}E$ values were below 2.3. Third, DTP samples treated with continuous after-treatment system were tested for fastness(washing, light, rubbing). Grades of fastness(washing, light, rubbing) were above 3 grade.