• Transactions of Materials Processing
• /
• v.10 no.4
• /
• pp.319-328
• /
• 2001

Quantitative evaluation of the tribological conditions at the tool-workpiece interface in metal forming is usually accomplished by the ring compression test. This paper describes an experimental investigation into friction factor under warm forming conditions according to the lubricants and the lubricating methods using the ring compression test. Four different lubricants, two water based graphite and two oil based graphite lubricants, and three different lubricating methods were applied in the experiments. Calibration curves with the friction shear factor were obtained using FEM analysis and verified by the experimental results. The influence of lubricant and lubricating methods on friction are discussed. In the ring compression test, the lower friction factor got to spray the oil based lubricant on die and billet in warm forging temperature.

• Transactions of Materials Processing
• /
• v.11 no.3
• /
• pp.211-216
• /
• 2002

The mechanical and thermal load, and thermal softening occuring by the rush temperature of die, in warm and hot forging, cause wear, heat cracking and plastic deformation, etc. This paper describes the effects of solid lubricants and surface treatments for warm forging die. Because cooling effect and low friction are essential to the long life of dies, optimal surface treatments and lubricants are very important to hot and warm forging process. The main factors affecting die hardness and heat transfer, are surface treatments and lubricants, which are related to heat transfer coefficient, etc. To verify the effects, experiments are performed for heat transfer coefficient in various conditions - different initial billet temperatures and different loads. Carbonitriding and ionitriding are used as surface treatments, and oil-base and water-base graphite lubricants are used. The effects of lubricant and surface treatment for warm and hot forging die life are explained by their thermal characteristics, and the new developed technique in this study for predicting tool life can give more feasible means to improve the tool life in hot forging process.

• Transactions of Materials Processing
• /
• v.11 no.3
• /
• pp.255-261
• /
• 2002

The grain size of 7010 Al alloy was refined to submicrometer level by using equal channel angular pressing (ECAP) and additional warm rolling. The mechanisms of grain refinement in ECAP process were fragmentation of coarse grain to ultra fine subgrains after a few passes and continuous recrystallization of the subgrains with the increase o( passes. Because of ultrafine grain size, essentially low temperature and high strain rate superplasticity was observed after ECAP process and warm rolling to form a sheet metal. The maximum elongation of 700% was obtained for an ECA pressed specimen after IS passes without warm rolling at $450^{\circ}C$ with strain rate of 5x$10^{-3}$/sec.

• Transactions of Materials Processing
• /
• v.21 no.2
• /
• pp.113-118
• /
• 2012

Magnesium sheet alloys possess limited plastic formability at room temperature but their formability is substantially improved at elevated temperatures and optimum strain rates. In the present paper, three different types of failure criteria, namely, strain-based, stress-based, and work-based criteria, are compared for their applicability to warm press forming of magnesium sheet alloys. Warm deep-drawing experiments were conducted on AZ31 alloy sheet, and the results were used to assess the strength and weakness of the failure criteria.

• Transactions of Materials Processing
• /
• v.13 no.7
• /
• pp.623-628
• /
• 2004

This paper is concerned with pressure welding, which has been known as a main bonding mechanism during the cold and warm forming such as clad extrusion or bundle extrusion/drawing. Bonding characteristics between the Cu and Al plates by pressure welding are investigated focusing on the weak bonding. Experiments are performed at the cold and warm temperatures ranging from the room temperature to $200^{\circ}C$. The important factors examined in this work are the welding pressure, pressure holding time, surface roughness, and temperature. A bonding map, which can identify the bonding criterion with a weak bonding strength of IMPa , is proposed in terms of welding pressure and surface roughness fur the cold and warm temperature ranges.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.277-280
• /
• 2006

The hydroformability of aluminum alloy sheets at elevated temperatures have been investigated in this study. It is necessary to analyze the variations of the mechanical properties that depend on the forming temperature and the heat conduction during warm hydroforming. Therefore, in this study a coupled simulation of plastic deformation and temperature distribution in the warm hydroforming process is performed and compared with experimental data. The multi-purpose code DEFORM-2D can handle this type of calculations but it takes high computation time if contact heat transfer between die, tube and pressure medium occurs. Experiments were conducted by high temperature tribometer(pin-on-disk) allowing measuring the friction coefficients of the aluminum alloys at several temperatures and these results are applied to the coupled simulation by which the optimal process parameters such as internal pressure and preset temperature on hydroformability can be determined. The comparison of the FE analysis with the experimental results has shown that hydroformability given by bulge height, and temperature distribution of the tube specimen make a little difference with the FE results but the trend predicted by simulation agrees well with experiments.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.318-321
• /
• 2006

In this strudy, the free-bulge test and FE analysis have been used to define the fracture criteria based on the cockroft and Latham's criterion in warm hydroforming of Al 6061 tube. Full annealing and T6 treatment for heat treatment of Al 6061 tube ware used in this study. As-extruded, full annealed and T6-treated Al 6061 seamless tubes were prepared. To evaluate the hydroformability, uni-axial tensile test and bulge test were performed between room temperature and $200^{\circ}C$. And measured flow stress was used to simulate the warm hydroforming. A commercial FEM code, DEFORM-$2D^{TM}$, was used to calculate the damage value. A forming limit based ductile fracture criteria has been proposed by the results of experimental and FE analysis. The calculated values for fracture criteria will be efficient to predict the forming limit in hydroforming for real complex shaped part.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.75-78
• /
• 2000

There are several effective factors to influence die life in the warm forging process. For instance process design die design and die materials etc This study presented heat treatment method which could improve toughness and wear resistance simultaneously in high temperature to apply high speed tool steels like SKH51 to die material for warm forging process. To verify the feasibility of application of heat treatment method mentioned above wear test was performed under the condition of constant time in 40$0^{\circ}C$ Wear coefficient was examined to search a relation between wear amount and time for each material and heat treatment method in 30, 60, and 130 minutes. To quantify the toughness-behavior between room and high temperature impact test was performed and heat fatigue test also fulfilled to compare with the resistance of heat check in room, 200, 400, and $600^{\circ}C$ temperature. On the basis of experimental results mentioned above high speed tool steel was applied to verify appropriateness of newly proposed heat treatment method for die of rotor pole used in automobile alternator. As a result die life of high speed tool steel applied newly proposed heat treatment is longer than that of STD61.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.463-473
• /
• 2011

The warm shrink fitting process is generally used to assemble automobile transmission parts (shaft/gear). But the fitting process can cause the dimensions of addendum and dedendum of the gear to change with respect to the fitting interference and the profile of the gear. As a result, there may be additional noise and vibration between gears. To address these problems, we analyzed the warm shrink fitting process according to process parameters; the fitting interference between the outer diameter of the shaft and the inner diameter of the gear, the inner diameter of the gear, addendum and dedendum of the gear, the heating temperature. In this study, a closed form equation for predicting the amount of deformation of addendum and dedendum in the R-direction was proposed. And the FEA method to analyze the cooling process was proposed for thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process).

• Journal of Institute of Convergence Technology
• /
• v.2 no.1
• /
• pp.18-23
• /
• 2012

The purpose of this study is to visually confirm on variation of temperature changes according to the basic of Kumdo by using infrared rays camera and to obtain the difference of temperature distribution according to the warm up procedure. We selected randomly two Kumdo players, and recorded twice continuously their actions of three basic(Head Hitting, Wrist Hitting, Waist Hitting) motions of Kumdo. In other to obtain the effect of warm up procedure, we recorded again their actions including warm-up motions. Four measuring points on the body were selected in each motion considering the error on continuous recoding. Temperature distributions of the before and after warming up procedure were analyzed at two measuring point. Skin temperature distributions of the players's body in two cases are shown a similar tendency. It can be predicted that the parts of large physical movement result in the large changes of temperature according to the warm up motion.