• Resources Recycling
• /
• v.23 no.2
• /
• pp.46-52
• /
• 2014

This study was conducted to observe the removal efficiency of oil-contaminated soil by various tests using microwaves and high-temperature heating elements. The water content was measured with the treatment amount, which was lowered to 300g in a relatively short amount of time. The treatment rate of TPH(Total Petroleum Hydrocarbons) showed the highest value with 70.1% when the SiC-activated carbon heating element was at 4 kW/kg, compared to the SiC heating element used alone. In particular, the higher electric power became, the higher treatment rate became, except at 3 kW. In the case of the heating element made by the fusion of SiC and activated carbon, the internal temperature exceeded $300^{\circ}C$ and again fell when it was treated at 4 kW for about 2 minutes. Then, after about 8 minutes, it rose again. On the basis of such results, the energy content necessary for the sample was calculated according to the electric power of microwaves, and tthe constant of TPH treatment was measured by tests on the treatment characteristics of oil-contaminated soil.

• Geomechanics and Engineering
• /
• v.31 no.4
• /
• pp.385-393
• /
• 2022

Previous studies postulated insignificant capillary rise (h_c) effect above the water table (H_w) for unsaturated soils. In addition, these studies utilised dry unit weight above H_w. This paper, therefore, addresses the effect of these postulations on strength where the influence of h_c using a modified upper bound approach, Discontinuity Layout Optimization (UNSAT-DLO) for a simulated soil was predicted. Two different parametric studies to model passive earth pressure and bearing capacity problems are carried out to provide an insight into the effect of capillary rise on strength. Significant increase in strength, owing to unsaturated conditions, was obtained where the maximum increase was when suction slightly less or greater than the air entry suction. On the other hand, the results showed a negative effect of h_c. For example, up to 8.24% decrease in passive thrust (P_p) was obtained at H_w=0 m when h_c rose 1 m from 0 m. To put this into perspective, this was equivalent to a decrease of about 2° in 𝜙 at H_w=0 m and h_c =0 m in order to obtain the same result at h_c =1 m. For the bearing capacity problem, the effect was seen to be higher, up to 18.4% decrease in N_𝛾 was obtained when h_c rose from 0 m to 2.5 m at H_w =0 m. In addition, the results revealed a negative influence of assigning dry unit weight above H_w or h_c.. However, considerable increase in strength was obtained when unsaturated unit weight above h_c was assigned.

• Journal of The Korean Astronomical Society
• /
• v.29 no.spc1
• /
• pp.183-186
• /
• 1996

We report the results of H I 21-cm and molecular line studies of the shocked interstellar gas in the W51 complex. We present convincing evidences suggesting that the shocked gas has been produced by the interaction of the W51C supernova remant (SNR) with a large molecular cloud, Our results show that W51C is the second SNR with direct evidences for the shocked cloud material.

• Korean Journal of Materials Research
• /
• v.14 no.9
• /
• pp.649-654
• /
• 2004

In this paper, the fracture toughness and mechanisms of failure in a random SiC-whisker/$Al_{2}O_3$ ceramic composite were investigated using in situ observations during mode I(opening) loading. $SiC_{w}/Al_{2}O_3$ composite was obtained by hot press sintering of $Al_{2}O_3$ powder and SiC whisker as the matrix and reinforcement, respectively. The whisker and powder were mixed using a turbo mill. The composite was produced at SiC whisker volume fraction of $0.3\%$. Compared with monolithic $Al_{2}O_3$, fracture toughness enhancement was observed in $SiC_{w}/Al_{2}O_3$ composite. This improved fracture toughness was attributed to SiC whisker bridging and crack deflection. $SiC_{w}/Al_{2}O_3$ composite exhibited typically brittle fracture behavior, but a fracture process zone was observed in this composite. This means that the load versus load-line displacement curve of $SiC_{w}/Al_{2}O_3$ composite from a fracture test may involve a small non-linear region near the peak load.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.221.2-222
• /
• 2003

The relative retrogradation of Jeungpyun investigated with different millimg methods of rice flour. The relative retrogradation of Jeungpyun was reduced in order that of W-C, W-P, D-M, D-J in DSC(Differential Scanning Calorimetry) method while W-C, D-M, D-J, W-P in Diastase method. In wet milling method, the relative retrogradation of Jeungpyun by Pin mill(W-P) was lower than Jeungpyun by colloid mill(W-C). In dry milling method, the relative retrogration of Jeungpyun by jet mill(D-J) was lower than Jeungpyun by micro mill(D-M). The relative retrogradation of Jeungpyun by DSC method was similar to the Diastase method. The relative retrogradation of Jeungpyun was decreased with decreasing particle size and setback value for amylogram and increasing damaged starch.

• Food Science and Preservation
• /
• v.21 no.3
• /
• pp.334-340
• /
• 2014

The moisture sorption isotherms of corn powder prepared from corn kernels roasted for 20 min at 160, 180, 200, 220, and $240^{\circ}C$ were determined at $20^{\circ}C$ using the static gravimetric method over the range of water activities ($a_w$) of 0.11~0.90. The moisture sorption isotherms showed a typical sigmoid shape, and the equilibrium moisture content tended to increase with increasing $a_w$, and increased sharply at above 0.75 $a_w$. At above 0.53 $a_w$, the equilibrium moisture content of the roasted corn powder increased with the increase in the roasting temperature. Six mathematical models (Bradley, Caurie, Halsey, Henderson, Kuhn, and Oswin) were used to fit the experimental data. The Oswin, Caurie, Henderson, and Halsey models were found to have suitability for describing the sorption curves, and the Oswin model was the best fit model for all the roasting temperatures. Concerning the monolayer moisture content, the Guggenheim-Anderson-Boer (GAB) equation showed high significance. The monolayer moisture content increased as the roasting temperature was increased, to 0.043 and 0.053 kg $H_2O/kg$ solids in the corn powder roasted at $180^{\circ}C$ and $240^{\circ}C$, respectively. These results suggest that the roasting temperatures of the corn kernels affected the moisture sorption characteristics ($20^{\circ}C$) of the corn powder.

• Journal of Biomedical Engineering Research
• /
• v.19 no.4
• /
• pp.333-339
• /
• 1998

The effect of heat treatment conditions on the properties of tungsten(W) embolization coils has been evaluated. The W embolization coils were fabricated by coiling the primary W coil with a diameter of 30.mm on a alumina rod mandrel with a diameter of 2.92mm. The secondary coils were then heat treated at 475$^{\circ}C$and 600$^{\circ}C$ for various heat treatment time ranging from 5 minutes to 36hours. The pitch distance, diameter and shape retention capability of the W embolization coils were characterized after the heat treatment. The pitch distance of the W embolization coils increased with the heat treatment time. The diameter of W emboliazation coils decreased continuously with heat treatment time. The shape retention capability of the W embolization coils increased with the heat treatment time due to an increase in elasticity by formation of tungsten oxide film on W coil surface during the heat treatment. The heat treatment condition of W embolization Col at 600$^{\circ}C$ for 20 minute was considered desirable based on the optimization of the shape retention capability, pitch distance and secondary coil diameter after heat treatment.

• Fire Science and Engineering
• /
• v.32 no.1
• /
• pp.46-56
• /
• 2018

The paper relates to a study on the conduction heat transfer characteristics according to the heating temperature of lightweight panel wall material. Plywoods, marbles, heat resistant glasses, as well as general gypsum board and fire-proof gypsum board, which have been widely used for lightweight panel wall material, were selected as experiment samples, and heating temperatures were set as $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$. Next, each of the heating temperatures were introduced on the bottom part of the wall material for 30 minutes, and analyses were made on the heat transfer characteristics to the backside part on the top part through conduction. As results of the experiment, the maximum backside temperatures were measured up to $190^{\circ}C$ for a general gypsum board, $198^{\circ}C$ for a fire-proof gypsum board, $189^{\circ}C$ for a plywood, $321^{\circ}C$ for a marble, and $418^{\circ}C$ for a heat resistant glass as heating temperatures were introduced maximum of $600^{\circ}C$. In addition, the maximum change rate of conduction heat transfer were measured up to 85 W for a general gypsum board, 95 W for a fire-proof gypsum board, 67 W for a plywood, 1686 W for a marble, and 3196 W for a heat resistant glass as the maximum heating temperatures were introduced up to $600^{\circ}C$. Also, carbonization characteristics of the wallpapers were measured to visually check the danger of conduction heat transfer, and the results showed that smokes were first generated on the attached wallpapers for the heating temperature $600^{\circ}C$, which were 1021 s for a general gypsum board, 978 s for a fire-proof gypsum board, 1395 s for a plywood, 167 s for a marble, and 20 s for a heat resistant glass, and that the first generation of carbonization were 1115 s for a general gypsum board, 1089 s for a fire-proof gypsum board, 1489 s for a plywood, 192 s for a marble, and 36 s for a heat resistant glass.

• Journal of Korean Society for Atmospheric Environment
• /
• v.12 no.2
• /
• pp.121-130
• /
• 1996

The catalysts composed of Pt, Pd and W as active-components, $Al_{2}O_{3}$ and $SiO_{2}$ as supports, were perpared on the honeycomb type substrate and characterized by BET, SEM, TGA, FT-IR and XRD for diesel emission control. CO, $C_{3}H_{6}$, and $SO_{2}$ oxidation was carried out over these catalysts in a fixed bed continuous flow reactor at the temperatures between 100-500.deg.C and reactant gas was composed of 10 vol.% $O_{2}$, 1 vol.% CO, 0.8 vol.% $C_{3}H_{6}$ and 88.2 vol.% $N_{2}$. It was found that under these experimental conditions, the CO, $C_{3}H_{6}$ oxidation activity of Pt-W catalyst was higher than that of any other prepared catalyst, and this catalyst had also a good inhibition effect on $SO_{2}$ oxidation. Also it was show that the influence of $SO_{2}$ on $Al_{2}O_{3}$ was more sever than that of $SO_{2}$ on $SiO_{2}$.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1149-1150
• /
• 2006

The oxidation of (W,Mo)$Si_2$ powders has been investigated at 400, 500 and $600^{\circ}C$ for 12.0 hours in air. It was shown that the low temperature oxidation resistance of (W,Mo)$Si_2$ was worse than that of $MoSi_2$, and they showed great changes in mass, volume and colour. Especialy at $500^{\circ}C$, the amount of volume expansion of (W,Mo)$Si_2$ was as high as about $7\sim8$ times and color changed from black to yellow after 4.0h with $MoO_3$, $WO_3$, (W,Mo)$O_3$ and amorphous $SiO_2$ as main reaction products. The mass gain and oxidation rate were relatively slower at $400^{\circ}C$ and $600^{\circ}C$ than that at $500^{\circ}C$.