• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.181-181
• /
• 2012

The microwave probe for measuring plasma density is widely used for its advantages: First, it is not affected by the reactive gas. Second, it can measure local plasma parameters such as plasma density, plasma potential and plasma temperature. Third, it is simple and robust. A cut-off probe is the one of the most promising microwave probe. Recently, Kim et al. reveals the physics of the cut-off probe but the effect of the sheath on the determination of the plasma density is not explained. In this presentation, for taking account of sheath effects on determination of plasma density from the cut-off peak, a simplified circuit modeling and an E/M simulation are conducted. The results show that occupation ratio of sheath volume between two tips of the cut-off probe and subsequence pressure condition mainly change position of the cut-off peak with respect to plasma frequency. Magnitude of relative voltage taken on the impedance of sheath and the impedance of bulk plasma can explain this effect. Furthermore, effects of gap size, tip radius, and tip length ware revealed based on above analysis.

• Journal of the Korean Chemical Society
• /
• v.38 no.3
• /
• pp.179-185
• /
• 1994

The Raman stretching frequency of nitrile group was affected by change of solvents and its in concentration in same solvent. In the case of acetonitrile, nitrile group stretching frequencies were observed in the region of 2247.3∼2254.9 cm-1 with various solvents. While in benzonitrile, they were found in the region of 2226.1∼2230.3$ cm^{-1}. With the addition of water in acetonitrile,νC≡N was shifted to high frequency from 2250.1 cm^{-1} in pure acetonitrile to 2257.7 cm^{-1} in 90% water forwhich had with higher volume % of water caused higher hydrogen-bonded equilibrium between methyl protons and water. The νC≡N frequency for nitrile group was shifted to high frequency by solvent inductive effect with the increasing mixed solvent (CHCl_3/CCl_4)$mole% ratio.

• Journal of the Korean Chemical Society
• /
• v.36 no.1
• /
• pp.100-106
• /
• 1992

The fluorescence characteristics of copolymers of styrene-maleic anhydride(PSMAn), styrene-maleic acid (PSMA), and PSMA complexed with $Eu^{3+}$ (PSMA-Eu) in tetrahydrofuran were studied. The excimer of PSMA and PSMA-Eu with 75% mole fraction of styrene appears to have larger binding energy than that with 50% or 67% styrene. The ratio of excimer to monomer intensities showed little change with the increase of styrene concentration up to $8.0{\times}10^{-3}M$, indicating the excimer formation is due to intramolecular process. Three existing mechanisms for intramolecular excimer formation are considered inadequate to explain the observed behavior. The quenching of excimer intensity by benzyl-acetate, mesitylene, and $CCl_4$ is interpreted in terms of the molar volume of quencher.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.1 s.232
• /
• pp.55-62
• /
• 2005

Combustion Characteristics and quenching criteria of micro combustor in various condition was exploited experimentally. Two different gases were used, and various geometric matrixes were considered to figure out quenching characteristic of micro combustor. The micro combustor studied in this study was constant volume, and has cylindrical shape. Geometric parameter of combustor was defined to be combustor height and diameter. The effect of height was exploited parametrically as 1 mm, 2mm and 3mm and the effect of diameter was parameterized to be 7.5mm and 15mm. Three different combustibles. (1) Stoichiometric mixture of methane and are, (2) Stoichiometric mixture of hydrogen and air and (3) Mixture of hydrogen and air with fuel stoichiometry of two were used. Pressure transition during combustion process was recovered. The ratio of maximum pressure to initial pressure responded favorably with the change of height of combustor and the initial pressure, the maximum pressure was also increased. The flame propagation was observed only when a specific condition was satisfied. From the experiment the condition that guarantees stable propagation of flame was tabulated. The tabulated results includes criteria of quenching according to combustor height, combustor diameter, species of fuel and initial pressure.

• Journal of Korea Foundry Society
• /
• v.14 no.1
• /
• pp.45-51
• /
• 1994

The possibility of using bulk talc as molding material was reviewed and tested with the measurement of thermal properties and computer simulations. The measured thermal conductivity and heat diffusivity($k{\rho}c$) of talc were $2.4W/m^{\circ}C$ and $6.6{\times}10^6J^2/m^4^{\circ}C^2s$, respectively. Thermal properties of talc could be ranked between those of sand mold and iron mold. Talc transforms into cristobalite and enstatite at $910^{\circ}C$, During the transformation volume and structure change, cracks appear on the surface and distortion occurs. Therefore talc can be used for molding material below $910^{\circ}C$ if carefully treated. Computer simulation was carried out to test whether talc insert could promote directional solidification in sand mold and iron mold. In sand mold, it was possible to achieve directional solidification of thin plate casting with the length to thickness ratio of 15, if both iron insert and talc insert were used. In iron mold, it was possible to achieve directional solidification only with talc insert.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1159-1165
• /
• 2007

This study aims to determine the effects of sample movement and storage on sample disturbance. To this end, non-disturbed samples collected from the OOregion, Gwangyang City, Jeonranam-do. Then, unconfined compression and consolidation tests were performed on the samples in the field, Seoul Lab and Seoul Lab after 4 weeks. Based on failure strain rate$(\epsilon_f)$, volume strain rate$(\epsilon_{\nu})$, and void ratio change$({\Delta}e/e_0)$ obtained from the test results, sample disturbance was evaluated. The sample disturbance level was used to compare and analyze the influences of transportation and storage on sample disturbance.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.43-46
• /
• 2005

Micro molding technology is a promising mass production technology for polymer based microstructures. Mass production technologies such as the micro injection/compression molding, hot embossing, and micro reaction molding are already in use. In the present study, we have developed a numerical analysis system to simulate three-dimensional non-isothermal cavity filling for hot embossing, with a special emphasis on the free surface capturing. Precise free surface capturing has been successfully accomplished with the level set method, which is solved by means of the Runge-Kutta discontinuous Galerkin (RKDG) method. The RKDG method turns out to be excellent from the viewpoint of both numerical stability and accuracy of volume conservation. The Stokes equations are solved by the stabilized finite element method using the equal order tri-linear interpolation function. To prevent possible numerical oscillation in temperature Held we employ the streamline upwind Petrov-Galerkin (SUPG) method. With the developed code we investigated the detailed change of free surface shape in time during the mold filling. In the filling simulation of a simple rectangular cavity with repeating protruded parts, we find out that filling patterns are significantly influenced by the geometric characteristics such as the thickness of base plate and the aspect ratio and pitch of repeating microstructures. The numerical analysis system enables us to understand the basic flow and material deformation taking place during the cavity filling stage in microstructure fabrications.

• Transactions of the Society of Information Storage Systems
• /
• v.7 no.1
• /
• pp.19-24
• /
• 2011

Holographic Data Storage System, one of the next generation data storage devices, is a 2-dimensional page oriented memory system using volume holograms in writing and retrieving process. Recently photopolymer with disc type substrate was selected as a media for the Holographic Data Storage System. The disc tilt occurs when the media rotates and the external disturbance applies. The disc tilt causes the change of the angle between the reference beam and the media, the data cannot be retrieved with the right angle or other data page is retrieved. The tilt is generated in a 2-axis direction (tangential, radial). The tangential tilt direction is the same with the multiplexing plane, while the radial tilt direction is a perpendicular to the multiplexing plane. In this research we propose 2-axis tilt angle servo system. The tilt errors are measured by using external photo detector and the additional red laser. Then the tangential direction tilt is compensated by using the galvano mirror. Also the radial direction tilt is compensated by the rotating prism between the relay lens in the reference field. Finally we confirm the compensation results through the Signal to Noise Ratio(SNR) and Bit Error Rate(BER).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.3
• /
• pp.269-277
• /
• 1999

The purpose of this study is to investigate the structural behavior of reinforced concrete columns rehabilitated with epoxy-bonded steel plates subjected to axial load. Eleven specimens were made to evaluate structural capacity of reinforced concrete columns rehabilitated with steel plates. This study considers the change of the internal force and the deformation of reinforced concrete column with reinforcing steel plates, and analyzes the effect of the improvement of strength and ductility. Based on the test results, this study brings the following conclusions. In case of the effect of reinforcement by the ratio of the same volume, the internal force for the test model, which the width of the reinforcing steel plate is small, is effectively higher. The smaller the width and the thickness of reinforcing steel plate, the more effective the effect of reinforcement is. For applying the theorical equation by Uzumeri, the maximum load and the coefficient of effective crossing reinforcement by the width and the thickness of steel plate reflected the properties of reinforcing steel plate.

• Korean Journal of Metals and Materials
• /
• v.50 no.9
• /
• pp.619-627
• /
• 2012

One of the barriers limiting wide applications of magnesium alloys to various industries is their poor corrosion resistance. The corrosion properties of AZ91 magnesium alloy, which is the most popular magnesium casting alloy, are affected by microstructural and environmental factors. The corrosion properties of AZ91 magnesium alloy are affected by the corrosion properties of ${\alpha}-Mg$ and ${\beta}$ phases, the volume fraction and distribution of ${\beta}$ phase and area ratio of ${\alpha}-Mg/{\beta}$ phases. The corrosion properties of AZ91 magnesium alloy under various environments also change according to the passivity of films and types of corrosion products formed on its surface. The corrosion resistance of the magnesium alloys can be improved by microstructural control through the addition of alloying elements and optimization of the production process.