• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.6
• /
• pp.1375-1381
• /
• 2010

LED(Light Emitting Diode) is an emitting device which energy is same to the bandgap energy of p-type and n-type semiconductor junction. Recently high brightness LED is used in fish-luring light and traffic signal light alternative of normal light bulb, and widely used in the area of display pannel. Moreover nowadays LED has been used as a back light of LCD display. Recently, visible light communication(VLC) using LED, that allow two-way serial data communication between LEDs over a distance of sveral centimeters or meters, has been widely studied in the area of digital information transmission along with illumination and display. In this paper, we present LED communication system and their applications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.8
• /
• pp.1773-1779
• /
• 2015

Shore-to-sea visible light communication using color clustered multiple-input and multiple-output (MIMO) is presented. The proposed maritime visible light communication (MVLC) offers a low-cost, high-speed wireless link for shore-to-sea maritime communications. Each color cluster is comprised of 50 red, green and blue (RGB) light emitting diodes (LEDs) and is modulated using on-off-keying (OOK). Selection combining is performed at the receiver, producing diversity effect within that color cluster. In this paper, we employ sea states (wave height, wind speed, etc.) data from both Pierson-Moskowitz and JONSWAP spectrum models under atmospheric turbulence conditions. Based on the simulation model, the maritime link quality is analysed in terms of coverage distance and bit error rate performance. The results show that the proposed system provides an efficient MVLC, while satisfying International Association of Lighthouse Authorities (IALA) requirements for maritime buoyage system and also offering sufficient illumination from high power LEDs.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.11-12
• /
• 2012

In this paper, efficient visible light communication technology LED (Light Emitting Diode) lighting through the existing infrared sensor used for performance analysis of transmitting and receiving is possible. LED utilizes lighting by changing light into electricity. Lighting features while maintaining the basic principles of flashing LED and PD (Photo Diode) to send and receive communications from LED lighting communication convergence principle be realized simultaneously enabling. Multiple IT applications under the basic structure of LED technology development, and the current was encountered in real life. LED lighting anywhere with wireless communication technology that can, in order to ~ 1m above the initial value by taking advantage of the system H/W and infrared sensors(PD) are widely used in the entire system that can improve the speed of visible light data transmission system is finished. LED module that is used to communicate whether the performance analysis, For forecasting and communication distance on the LED and infrared sensor configuration of the implementation of the research is to study about the possibility of application methods and indicates.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.6
• /
• pp.476-481
• /
• 2014

In this paper, we design the pre-equalizer of transmitter circuit in order to enhancement modulation bandwidth of white LED which is light source of VLC (Visible Light Communication). Also, we eliminate yellow light component by optical filtering which mitigate frequency response of white LED. Power loss by optical filtering is overcome by using convex lens. By applying proposed system, 3 dB bandwidth deciding modulation bandwidth of white LED increases from 3 MHz to more than 25 MHz and the transmission distance increases by optical design which secure additional signal power. We optically modulate NRZ-OOK signal to LED and receive light signal using APD. We analyze received data using CSA and RFSA. As a result, we experimently demonstrate the possibility that transmits NRZ-OOK signal up to 30 Mbps in 4.5 m, 50 Mbps in 1.5 m through the pre-equalizer and optical design.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.473-477
• /
• 2015

In this paper, a commercial phosphorescent white light-emitting diode (WLED) visible light communication (VLC) system with an equalization circuit to achieve the high modulation bandwidth was designed and demonstrated. An analytical method to examine the performance of the equalizer was carried out using a general circuit-simulator, PSpice. The equalization circuit was composed of two passive filters with resisters and a capacitor and an active filter with an op-amp. Utilizing our post-equalization technology, the ~3.5 MHz bandwidth of phosphor WLED could be extended to ~25 MHz without using an optical blue-filter. In this VLC system with a single round-type WLED and a single PIN photo-diode, ASK data transmission up to 35 Mbps at a 1m free space distance was obtained. The resulting bit-error-rate was $7.6{\times}10^{-4}$, which is less than the forward error correction (FEC) limit of $3.8{\times}10^{-3}$.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.91-97
• /
• 2018

This paper presents implementation possibilities of digital IoT doorlock systems via VLC(Visible Light Communication)'s color grid. The color grid-based VLC modulation scheme which are discussed in this paper utilize the straightness of light and abundant frequency resources which are the properties of the light. Performance results in this paper are compared to that of conventional modulations with Bit Error Rate (BER) and Signal to Noise Ratio (SNR) simulations. With respect to a channel model, the proposed modulation schemes select the nearest Line Of Sight (LOS) except Non Line Of Sight (NLOS). Experiments in this paper show error rates of received symbols by changing power dB at a distance of 3m between Tx and Rx in an indoor environment. Through performance results and experiments, this paper demonstrates superiority of the proposed color grid-based modulation schemes.

• Korean Journal of Environmental Agriculture
• /
• v.14 no.2
• /
• pp.144-154
• /
• 1995

This study was conducted for the evaluation of air-pollution using pear plant. Twenty-three sites around the Ulsan Industrial Complex Area were selected for the study. The water soluble sulfur content, photosynthetic rate and the visible injured index of pear leaves were evaluated and the results are summarized as follows: 1. Water-soluble sulfur content of pear leaves at survey sites was shown to be an average of 0.201%. The content of their leaves at polluted sites ranged from 0.220 to 0.496%. Water-soluble sulfur content of the pear leaves decreased as the distance became far from the Industrial Complex. 2. The photosynthetic rate of pear leaves decreased with an accumulation of water-soluble sulfur content. However it increased as the distance became greater within the five-kilometer radius of the pollutant. 3. More than 60% of injured rate was shown in pear plant within the five-kilometer radius of the pollutant in 1993. There were high correlations between the visible injured index items. Compared with 1988, the most severely injured sites in 1988 were Yochon-dong and Yaum-dong. But in 1993, they moved to the Yongcham-dong and Bugok-dong area. 4. Water-soluble sulfur content of pear leaves was correlated with the photosynthetic rate of pear leaves. The same tendency was shown between water-soluble sulfur and total injured index. This method using pear plant will be applied to the evaluation of air pollution.

• Restorative Dentistry and Endodontics
• /
• v.14 no.1
• /
• pp.179-188
• /
• 1989

The purpose of this study was to measure Micro vicker's hardness of 4 kinds of anterior Composite resins (Pyrofil light bond anterior, Lite-fil anterior, Photo clear fil anterior, Silux) and 6 kinds of posterior Composite resin (Pyrofil light bond posterior. Lite-fil posterior, Photo clear fil posterior, Occlusin posterior, Palfique light posterior, P-30, posterior) according to deference of depth and distance of light tip from surface of composite resin. Each composite resin was filled into Teflon tube of 5mm in diameter and 5mm in depth, celluloid matrix was covered and the light in accordance with each composite resin was irradiated in distance of zero millimeter and 1 cm from light tip to surface of composite resin for 30 seconds. Specimens were sectioned longitudinally with cutting device. Microvicker's hardness measurements ware made at the depth of surface, 1mm, 2mm, 3mm, 4mm and 5mm from the surface to deep portion. Vicker's hardness numbers were taken on each depth under 200gm load for 30 seconds with MVK-E. The following results were: 1. The highest hardness value was measured at 1 mm depth. Then the deeper the depth, the lesser the hardness was observed. 2. The hardness value of anterior composite resins is lower than one of posterior composite resins. 3. Hardness number of composite resin irradiated in distance of zero millimeter from surface of composite resin was higher than one of 1 cm from surface of composite resin. 4. The pattern of hardness change at varying depth was similar to all the experimental material with no relation to distance of light from specimen.

• Journal of Satellite, Information and Communications
• /
• v.10 no.1
• /
• pp.62-66
• /
• 2015

This paper introduces various applications and contents of digital signage, and analyzes conventional communication techniques to increase communication range. To realize digital signage in long distance, this paper proposes a hybrid modulation scheme and analyzes its performance. To verify its performance in real channel environment, we mapped symbols and experimented data transmission and reception with a visible light communication module with USRP. As a result, we confirmed a data receiving range and power of transmission and reception of the hybrid modulation mode. Also, we showed that the proposed modulation scheme has better performance of communication range and power efficiency than that of the conventional QAM technique.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.306-309
• /
• 2004

The susceptibility of landslides and the effect of landslide-related factors at Penang in Malaysia using the Geographic Information System (GIS) and remote sensing data have been evaluated. Landslide locations were identified in the study area from interpretation of aerial photographs and from field surveys. Topographical and geological data and satellite images were collected, processed, and constructed into a spatial database using GIS and image processing. The factors chosen that influence landslide occurrence were: topographic slope, topographic aspect, topographic curvature and distance from drainage, all from the topographic database; lithology and distance from lineament, taken from the geologic database; land use from Landsat TM (Thermatic Mapper) satellite images; and the vegetation index value from SPOT HRV (High Resolution Visible) satellite images. Landslide hazardous areas were analysed and mapped using the landslide-occurrence factors employing the probability-frequency ratio method. To assess the effect of these factors, each factor was excluded from the analysis, and its effect verified using the landslide location data. As a result, land 'cover had relatively positive effects, and lithology had relatively negative effects on the landslide susceptibility maps in the study area. In addition, the landslide susceptibility maps using the all factors showed the relatively good results.