• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.7
• /
• pp.671-677
• /
• 2010

In the present study, we designed a microfluidic platform for generating monodisperse droplets with diameters ranging from hundreds of nanometers to several micrometers. To generate fine droplets, T-junction and flow-focusing geometry are integrated into the microfluidic channel. Relatively large aqueous droplets are generated at the upstream T-junction and transported to the flow-focusing geometry, where each droplet is broken into smaller droplets of the desired size by the action of pressure and viscous stress. In this configuration, the flow rate of the inner fluid can be made very low, and the ratio of the inner- and outer-fluid flow rates in the flow-focusing region can be made very high. It has been shown that the present microfluidic device can generate droplets with diameters of approximately $1\;{\mu}m$ (standard deviation: <3%).

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.9
• /
• pp.698-706
• /
• 2006

Experiment and numerical calculation have been peformed to investigate mixed convection heat transfer between inclined parallel plates. Particle image velocimetry (PIV) with thermo-sensitive liquid crystal (TLC) tracers is used for visualizing and analysis. This method allows simultaneous measurement of velocity and temperature fields at a given instant of time. Quantitative data of the temperature and velocity are obtained by applying the color-image processing to a visualized image, and neural network is applied to the color-to-temperature calibration. The governing equations are discretized using the finite volume method. The results are presented for the Reynolds number ranges from 0.004 to 0.062, the angle of inclination, ${\Theta}$, from 0 to 45 degree and Prandtl number of the high viscosity fluid is 909. The results show velocity, temperature and mean Nusselt numbers distributions. It is found that the periodic flow of mixed convection between inclined parallel plates is shown at $0^{\circ}{\leq}{\Theta}<30^{\circ}$, Re<0.062, and the flow pattern can be classified into three patterns which depend on Reynolds number and the angle of inclination. The minimum Nusselt numbers occur at Re=0.05 regardless of the angle of inclination.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.341-346
• /
• 2004

A low NPSH and high pressure fuel pump has been designed for a turbopump system. The fuel pump has an axial inducer and a centrifugal impeller. A meanline method has been established for the preliminary design and performance prediction of pumps at design or off-design points. KeRC carried out a model testing of the fuel pump with water as a working fluid at the reduced speed. Predicted performances by the method are shown to be in good agreement with experimental results for cavitating and non-cavitating conditions. The established meanline method can be used for the performance prediction and preliminary design of high speed pumps which have a inducer, impeller and volute. In the current study, the three dimensional viscous flow in the fuel pump was investigated through numerical computation. A modified design of the fuel pun was generated to improve pump performance by utilizing CFD results. The modified fuel pump was experimentally tested by ROTEM and KARI. The measured non-cavitating and cavitating performance showed a good agreement with designed performance.

• 유체기계공업학회:학술대회논문집
• /
• 1998.12a
• /
• pp.42-48
• /
• 1998

Numerical study is presented for the analysis of three-dimensional incompressible turbulent flows in multiblade centrifugal fan. Reynolds-averaged Navier-Stokes equations with standard k - $\epsilon$ turbulence model are transformed to non-orthogonal curvilinear coordinates, and are discretized with finite volume approximations. Linear Upwind Differencing Scheme(LUDS) is used to approximate the convection terms in the governing equations. SIMPLEC algorithm is used as a velocity-pressure correction procedure. The computational area is divided into three blocks; core, impeller and scroll, which are linked by multi-block method. The flow inside of the fan is regarded as steady flow, and mathematical formula established from the cascade theory and empirical coefficient are employed to simulate tile flow through the impeller. From comparisons between the computational results and the experimental data, the validity of the mathematical formula for the blade forces was examined and good results were obtained qualitatively. Hence, we can get the flow characteristics of multi-blade centrifugal fan and it will be a corner stone of the development of the multiblade centrifugal fan.

• Journal of KSNVE
• /
• v.5 no.3
• /
• pp.303-311
• /
• 1995

Tests on flow-induced vibration of inclined cylinders in uniform flow were performed in the cavitation tunnel at the Korea Instituteof Machinery and Metals. The test program was intended to investigate flow-induced vibration characteristic of the cylinders with three different inclined angles of 10$^\circ$, 20$^\circ$ and 30$^\circ$ and to estimate the fluid force coefficients acting on the cylinders. Important observations are as follows: 1) Numal drag is dominant compared with viscous drag for the inclined angle over 20.deg. and it has the value from 1.7 to 2.0 as was observed by other researchers. 2) Lift force coefficient has large value at the lock-in range determined by 4$\Theta/f_nD$<8. Measured maximum lift force coefficients at the inclined angle of 30.$^\circ$ and 20$^\circ$ were 0.9 and 0.4 respectively.

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.99-107
• /
• 2014

The aim of the present study is to investigate the flow interference between two adjacent undulating fish-like body, and its effect on the undulating propulsion. For this purpose, unsteady two dimensional incompressible flow calculations were conducted using an unstructured mesh flow solver, coupled with an overset mesh technique. To deal with mesh deformation due to fish locomotion, spring analogy is utilized. The fish body used in the simulation is constructed from the NACA0012 airfoil. The study indicates that the propulsion of undulating fish is proportional to frequency and wavelength of the midline oscillation when there is no adjacent fish. It also reveals that average thrust was increased when the vortex shedding from the tail was conserved well and pressure difference between upper and lower sides of the fish was magnified due to flow interference. From this study, which relative position and phase difference of locomotion between two fishes can generate maximum thrust was known among six different cases.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.416-421
• /
• 2001

This paper presents the numerical prediction of sound generated by viscous flow past a circular cylinder. The two dimensional flow field is predicted using FEM based Reynolds-averaged Navier-Stokes solver, and the calculated unsteady fluid field values are utilized by an acoustic code that implements Ffowcs Willianms-Hawkings(FW-H) equation. The integration surface used in acoustic analysis is extended from the cylinder surface to permeable surfaces. The 2D based CFD calculations overpredict the acoustic amplitude, however, if adequate correlation length is used, the predicted acoustic amplitude agrees well with experiment. The predictions using extended integral surface in FW-H equation show results that contain the characteristics of quadrupole - volume integration - noise term, and do not vary seriously with the integral surface location.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.2 s.152
• /
• pp.93-100
• /
• 2007

Post swirl stator is an energy saving device to recover rotational energy of the propeller. To optimize the performance of post swirl stator in container vessels, computational fluid dynamics using body force method was introduced. A commercial code Fluent was used in conjunction with body force distributed on the surface of actuator disk which is located in the propeller plane to optimize pitch angle of the post swirl stator blade. This study showed that CFD is an important tool to simulate flow behind ship with propeller, rudder and post swirl stator.

• Journal of computational fluids engineering
• /
• v.13 no.1
• /
• pp.28-34
• /
• 2008

A particle method recognized as one of the gridless methods has been developed to investigate the nonlinear free-surface motions interacting to the structures. The method is more feasible and effective than convectional grid methods for solving the non-linear free-surface motion with complicated boundary shapes. The right-handed side of the governing equations for incompressible fluid, which includes gradient, viscous and external force terms, can be replaced by the particle interaction models. In the present study, the developed method is applied to the dam-broken problem on dried- and wet-floor and its adequacy will be discussed by the comparison with the experimental results.

• Journal of the Korean Institute of Navigation
• /
• v.19 no.3
• /
• pp.1-10
• /
• 1995

The effect of the submerged high speed vessel on the ocean wave is made clear in the point of hydrodynamics view. In connection to the design of high speed ship, the flow analysis is carried out to predict the pressure distribution for drag and lift. The purpose of the research is to help the preliminary design of the economic hull form advancing under the ocean wave by estimating the resistance performance and the wave behaviour. In the present study, more efficient numerical approaches are investigated for the viscous flow analysis around a submerged NACA0012 hydrofoil with the laminar and incompressible fluid. Through the numerical simulation, it is found that the new numerical method becomes more efficient primarily due to the fact that the wave elevation is reasonably developed.