• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.895-900
• /
• 2008

It is the objective of the present study to conduct correlation analysis for deriving control parameters in vertical shafts using the results obtain by the design of experiments in the preceding research. The control parameters are categorized into objective parameters, derived parameters, condition parameters, operation parameters, and sensing parameters. The maximum pressure in the shaft should be sufficiently small in order to maintain exhaust hood performance. The pressure variations between floors should also be minimized in order to maintain uniform exhaust performance between floors and to save energy for excessive pressure drop in the shaft. The standard deviation based on -4Pa is proposed as an objective parameter to control pressure in shafts. The correlation equation has been obtained between the standard deviation and the sensing parameters of outdoor temperature and the pressure at the top of the shaft.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.247-251
• /
• 2007

Because of the ozone layer depletion and global warming, new alternative refrigerants are being developed. In this study, evaporation heat transfer characteristics of carbon dioxide flowing upward in a vertical micro-fin tube have been investigated by experiment. Before a test section, a pre-heater is installed to adjust the inlet quality of the refrigerant to a desired value. The micro-fin tube with outer diameter of 5 mm and length of 1.44 m was selected as the test section. The test was conducted at mass fluxes of 318 to $530\;kg/m^2s$, saturation temperature of -5 to $5^{\circ}C$, and heat fluxes of 15 to $30\;kW/m^2$. As the vapor quality increases, the heat transfer coefficients of carbon dioxide are increased, and the heat transfer coefficients increase when the heat fluxes and saturation temperatures increase, and there was not much of influence of mass flux on the heat transfer coefficients.

• Atmosphere
• /
• v.20 no.1
• /
• pp.37-47
• /
• 2010

The methods measuring the precipitation drop size distribution(hereafter referred to as DSD) at Cloud Physics Observation System (CPOS) in Daegwallyeong are to use PARSIVEL (PARticle SIze and VELocity) disdrometer (hereafter referred to as PARSIVEL) and Micro Rain Radar (hereafter referred to as MRR). First of all, PARSIVEL and MRR give good correlation coefficients between their rain rates and those of rain gage: $R^2=0.93$ and 0.91, respectively. For the DSD, the rain rates are classified in 3 categories (Category 1: rr (Rain Rate) ${\leq}0.5\;mm\;h^{-1}$, Category 2: $0.5\;mm\;h^-1$ < rr < $4.0\;mm\;h^{-1}$, Category 3: rr ${\geq}4\;mm\;h^{-1}$). The shapes of PARSIVEL and MRR DSD are relatively most similar in category 2. In addition, we retrieve the vertical rain rate and liquid water content from MRR under melting layer, calculated by Cha et al's method, in Daegwallyeong ($37^{\circ}41{\prime}N$, $128^{\circ}45^{\prime}E$, 843 m ASL, mountain area) and Haenam ($34^{\circ}33^{\prime}N$, $126^{\circ}34^{\prime}E$, 4.6 m ASL, coast area). The vertical variations of rain rate and liquid water content in Daegwallyeong are smaller than those in Haenam. We think that this different vertical rain rate characteristic for both sites is due to the vertical different cloud type (convective and stratiform cloud seem dominant at Haenam and Daegwallyeong, respectively). This suggests that the statistical precipitation DSD model, for the application of weather radar and numerical simulation of precipitation processes, be considered differently for the region, which will be performed in near future.

• Journal of the Korea Concrete Institute
• /
• v.16 no.2 s.80
• /
• pp.221-228
• /
• 2004

In recent years building floors become larger and more spacious due to the development of new design methods and high strength and light weight materials. However, such long span floor systems may provide smaller amount of damping and have a longer period so that they may be more vulnerable to the floor vertical vibration. In Korea when floors are to be checked against the floor vertical vibration, the provisions developed in foreign countries have been used. However these guidelines have been developed based on human perception, which may vary from country to country. Also, Korea have particular floor systems, such as flat plate floor system of apartment building. This study attempts to evaluate the vibration performance of the floors in typical apartment buildings. Two different floors with the area of $28 m^2$ and $32 m^2$ were investigated. The criteria provided by ATC-1(1999), AISC-11(1997), AIJ(1991) and the local criteria developed in the previous study(Han, 2003) was used to check the acceptability of the floor vertical vibration.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.12
• /
• pp.17-21
• /
• 2020

Over 60% of South Korea's land consists of mountainous topography, and recently, due to earthquakes, localized heavy rains and road development, the risks of rockfalls are getting higher. As of now, rockfall prevention facilities are being constructed in 70% of Korean roads cut slope and rockfall protections account for about 20% of them. Rockfall protection's supporting capacity is defined by combining performance of wire mesh, pillars and wire ropes. For the existing constructed rockfall protection, standards of pillars that can absorb 48~61 kJ amount of energy, wire ropes and wire mesh are presented in Guidelines for the installation and management of traffic safety facilities, Rockfall prevention facilities by Ministry of Land, Transport and Maritime Affairs (2008). However, each factor's correlation of absorption energy is not presented so it is uncertain. This study will conduct vertical drop test and identify adequacy of rockfall protection net of displacement quantity calculation factor which is delta and evaluate rockfall protection net's absorbable energy through standards of overseas performance evaluation criteria.

• Fashion & Textile Research Journal
• /
• v.16 no.4
• /
• pp.625-634
• /
• 2014

This study develops a sizing system of mass-customized male suits for wheelchair users. One hundred and three male wheelchair users' 21 anthropometric dimensions were measured to identify body shapes and develop a sizing system. The measured wheelchair users' body sizes were compared with the average body sizes of Korean males from the $6^{th}$ Korean Body Size Survey to understand the body size differences between two groups. As a result of body shape classification using the KS's Drop method, wheelchair user body shapes were classified into four shapes for upper-body (A: 32%, B: 26%, BB: 24%, and Y: 18%), and two shapes for lower-body (B: 70% and A: 30%). The upper-body of wheelchair users was relatively developed than Korean males; however, the lower-body was relatively stunted. The key dimensions of a sizing system were selected as chest circumference, waist circumference, and trunk length, outside leg length based on the correlation analysis between anthropometric measures. The top sizes were determined considering chest and waist circumferences for horizontal sizes, and additionally the trunk length was divided into short, medium, and long groups for vertical sizes. The bottom sizes were selected considering the waist and hip circumferences for horizontal sizes, and additionally their outside leg length was divided into short, medium, and long groups for vertical sizes.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.4
• /
• pp.5-11
• /
• 2012

To identify the flow characteristics of the SMART reactor, a flow distribution model test and a numerical simulation are performed in KAERI. Among several part of the SMART reactor, the fuel assemblies are simulated using simulators because of the complexity. The geometries of the core in the SMART reactor and simulator are different, but some similarities are maintained such as the ratio of pressure drop in the vertical and cross directions. There are cross flow holes in each core simulator to reproduce the cross flow of SMART fuel assemblies. To know the flow characteristics of the cross flow, numerical analysis is performed. As the cross flow area is decreased, the pressure drop between inlet and outlet is decreased. Also, when the flow imbalance between two core simulators is constant, the cross flow area does not significantly affect the cross flow.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.7 s.166
• /
• pp.1065-1074
• /
• 1999

This study proposes the analysis and evaluation method of time series ultrasonic signal using the chaotic feature extraction for ultrasonic pattern recognition. Features extracted from time series data using the chaotic time series signal analysis quantitatively welding defects. For this purpose analysis objective in this study is fractal dimension and Lyapunov exponent. Trajectory changes in the strange attractor indicated that even same type of defects carried substantial difference in chaoticity resulting from distance shills such as 0.5 and 1.0 skip distance. Such differences in chaoticity enables the evaluation of unique features of defects in the weld zone. In experiment fractal(correlation) dimension and Lyapunov exponent extracted from 6dB ultrasonic defect signals of weld zone showed chaoticity. In quantitative chaotic feature extraction, feature values(mean values) of 4.2690 and 0.0907 in the case of porosity and 4.2432 and 0.0888 in the case of incomplete penetration were proposed on the basis of fractal dimension and Lyapunov exponent. Proposed chaotic feature extraction in this study enhances ultrasonic pattern recognition results from defect signals of weld zone such as vertical hole.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.23 no.2
• /
• pp.103-108
• /
• 2017

The amount of delivered parcels have been increasing according to the change and expansion of consumption pattern through e-commerce, and they are required to minimize breakout or failure under the delivery. In this study, we measured and analyzed the distribution environment data (vibration and impact) occurred in the packaging, which were prepared with 5 types by the weight and dimension, distributed from Seoul to Busan in Korea by 2 parcel delivery service companies through e-commerce order. Date showed the parcels had 3-5 times of drop impact and 0.3-0.7 m of drop height on average, and 0.8 Grms of vibration acceleration from equivalent equation to the vertical direction. The significant gap in service quality was not found between 2 parcel delivery service companies. This study is expected to be useful for designing the suitable packaging in order to enhance safe transportation of the delivered packaging, and furthermore useful for developing Korean testing method for Field-to-Lab simulation.

• Journal of the Korean Home Economics Association
• /
• v.39 no.2
• /
• pp.25-40
• /
• 2001

The purpose of this study is to provide for the basic data useful to the development of the quality of brassiere featuring a good wearing feeling and an effect of reinstating and correcting breast shape. For this purpose, 220 adult women aged between 20 and 59 were sampled to survey their actual breast shapes. The results of this study can be summarized as follows; 1 According to the increase of age, the items of height were decreased and items of width, depth, circumference and length were increased, being obeser and breast point were drooped. So volume and bottom are3 of breast of 40.50′s women′s age group were larger than 20.30′s women′s age group and breast point width of 40.50′s women was being wider by increase of interior dimensions of breast. 2. The components of adult women′s breast shape can be categorized into "obesity of breast", "upper dimensions of breast and drop", "lower dimensions of breast and drop", "location of breast point and vertical size of breast", "interior dimensions of breast", "exterior dimensions of breast" Such components of breast shape very in terms of weight or apparence depending on ages. Older women tend to have more droopy and widen breasts.