• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.9-14
• /
• 1993

Weathering of wood in a region of acid rain was performed by the test which thin veneers of Sitka spruce were exposed to outdoor weathering for a total of 18 weeks, with a daily soaking for 30 minutes in acidified water in the pH range 2~5.6. The weathering measured by weight loss and loss in maximum failure load in tension was accelerated by the increase in the acidity of acidified water and in the period of outdoor exposure. It was also shown that the weathering was accelerated even with low acidic conditions in the case of long exposure period, although the weathering was rapidly accelerated with high acidic conditions. When compared the degree of weight loss with that of loss in failure load by weathering, the latter was much greater. From the results of this research, it could be concluded that at pH 4.0 or below of precipitation, the acceleration of weathering of exterior wood would become serious problems, which would be caused deterioration in performance of exterior wood.

• Journal of Korean society of Dental Hygiene
• /
• v.18 no.6
• /
• pp.1037-1045
• /
• 2018

Objectives: The purpose of this study was to evaluation the effect of translucency on CAD/CAM ceramic according to different core/veneer thicknesses. Methods: A total of 42 samples from 2 groups of 7 ceramic cores, each with 3 thickness values (0.8, 1.0, 1.2 mm) were manufactured. The veneers were also manufactured in 3 thicknesses (0.3, 0.5, 0.7 mm). The group names were based on the name of the ceramic core (IPS e.Max CAD; LD, and IPS Empress CAD; LR). The associated number was determined by the combined thickness of the core and veneer: 1 = (0.8 + 0.7); 2 = (1.0 + 0.5); 3 = (1.2 + 0.3). The translucency was measured using a spectrophotometer and defined via the contrast ratio (CR) and translucency parameter (TP). Two-way ANOVA was performed to compare the 2 groups (material and thickness). Results: As the core thickness increased, the TP value also increased, and the CR value (for LR group) decreased. The results of 2-way ANOVA demonstrated that the thicknesses of different core/veneer combinations significantly affected the translucency (p<0.05). Conclusions: The different core and veneer thicknesses affected the translucency of CAD/CAM ceramic.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.2
• /
• pp.239-248
• /
• 2019

This research presents an improvement of the physical and mechanical properties of composite board (com-ply) made of Oriented Strand Board (OSB) coated with wood veneer of Pine (Pinus merkusii), Avocado (Persea Americana) and Mahogany (Swietenia mahogany). 1.5 mm thick veneers of those three wood types were adhered to the surface of OSB using two adhesive types: epoxy and isocyanate. The adhesive with the glue spread of $250g\;m^{-2}$ applied using single glue line was spread and then cold pressed with the pressure of $15kg\;cm^{-2}$ for 3 hours. The research result showed an improving dimension stability of com-ply, but not found on all parameters of physical property test. The moisture content seemed to be influenced by the com-ply type, yet not related to its thickness swelling, water absorption and linear expansion. The exception took place in the parallel linear expansion when immersed for 2 hours. The highest to the lowest increases of MOE and MOR were consecutively found on OSB coated with wood veneer of Pine, Mahogany and Avocado. However, the increases were statistically insignificant. The highest increasing screw hold power was found at the com-ply type AE (avocado veneer and epoxy adhesive) that was by 28%.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.29 no.1
• /
• pp.25-34
• /
• 2020

In recent years, as a burden on tooth preparationduring the processing the laminate veneer treatments to enhance aesthetics, the interests and demands for non-prep laminate veneers are increasing which do not require teeth preparation. Although there are clear limitationsbecause the restorations are fabricated without tooth preparation, there is a clear advantage of non-invasivehealthy teeth. When manufacturing a non-prep laminate veneer, an effective design should be selected according to the aesthetic requirements and intraoral condition because the margin of restorationsshould be determined on the natural tooth surface that isnot prepared. In this article, I would like to presentthe three different designsaccording to the range which teeth are covered, and the advantages and disadvantages of them. Non-prep laminate veneer introduced in this article was fabricated using Lithium disilicate press ingot.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.1
• /
• pp.45-51
• /
• 2004

Combined microwave-convective drying of 2.4mm-thick radiata pine veneer grown in New Zealand was conducted to investigate drying characteristics. The veneers could be dried from 160% to 0% moisture content in 7.5 min by microwave drying combined with hot-air of 100℃. This drying rate is about three times higher than that of conventional convective drying with only hot air of 100℃. However there remained charred spots when too high microwave power was applied. Therefore investigations of the microwave-drying characteristics of veneer of various sizes and species are needed to determine the optimal drying conditions.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.29 no.1
• /
• pp.4-12
• /
• 2020

Recently, according to the concept of minimal invasive, there have been many opportunities for restoration treatment with porcelain laminate veneers that are less invasive and can ideally improve esthetics. Patients also visit the laminate well, and patients also want to reduce the amount of teeth cut, so the choice of the entire trimming crown is decreasing. Therefore, various techniques of laminate are required. Most dental clinicians seem to have negative images of laminates such as risk of fracture, margin pigmentation and dropout. However, this situation is due to incorrect adhesion manipulation and lack of inspection of the occlusal relationship, and there is no problem with the Porcelain Laminate Veneer itself. The purpose and scope of adaptation leading to the success of porcelain laminate veneer will be introduced.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.3
• /
• pp.241-247
• /
• 2017

Plywood, which is created by bonding an odd number of thin veneers perpendicular to the grain orientation of an adjacent layer, was developed to supplement the weak points such as contraction and expansion of conventional wood materials. With structural merits such as strength, durability, and good absorption against impact loads, plywood has been adopted as a structural material in the insulation system of a membrane type liquefied natural gas (LNG) carrier. In the present study, as an attempt to resolve recent failure problems with plywood in an LNG insulation system, conventional PF (phenolic-formaldehyde) resin plywood and its alternative MUF (melamine-urea-formaldehyde) resin bonded plywood were investigated by performing material bending tests at ambient ($20^{\circ}C$) and cryogenic ($-163^{\circ}C$) temperatures to understand the resin and grain effects on the mechanical behavior of the plywood. In addition, the failure characteristics of the plywood were investigated with regard to the grain orientation and testing temperature.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.36 no.2
• /
• pp.121-127
• /
• 2020

Prosthodontic decision and management should be considered the patient's aesthetic need for anterior teeth in maxillary edentulism. This case report describes 10-year clinical outcome of a maxillary edentulous patient was rehabilitated by means of an implant-supported fixed dental prosthesis (ISFDP) for the anterior region and a distal-extension removable partial denture (RPD) for the posterior region. The ISFDP was designed to splint 4 endosseous implants as one unit and engaged by the RPD. The edentulous mandible was restored by means of an implant-supported overdenture. Over the course, no major adverse event occurred other than wear, discoloration, and breakage of resin veneers and artificial teeth.

• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.1
• /
• pp.130-143
• /
• 1997

A heat-pressed technique(IPS-Empress, Ivoclar) has been described to construct single unit crown, inlay/onlay and veneers using a partially pre-cerammed and pre-colored glass-leucite ingot that has the greateast strength by the combination of heat-pressed procedure through the smalldiameter sprue and heat treatment procedure. The purpose of this study was to evaluate the flexure strength of a heat-pressed ceramic material(IPS-Empress) without simulated firing treatments according to pontic designs. Two groups of 9 disks(1.4mm thick, 14mm in diameter) each using two types of sprues with different diameters($({\Phi}2.8\;,{\Phi}1.8)$) and numbers were prepared. The specimens were mounted in the testing jig. The flexural strengths were determined, by means of the bi-axial bending test, by loading the center of disk to failure using a universal testing machine(Zwick 145141, Zwick, Germany) at a cross-head speed of 1.0 mm/min. The means flexural strength value of one group using a sprue with ${\Phi}2.8$ was $140.4{\pm}8.0Mpa$. That of the other group using two sprues with ${\Phi}1.8$ was $151.8{\pm}10.3Mpa$. After analysis, results showed that there was a statistical difference between groups(t=2.33m p<0.05). No clnical implications were drawn from these data because of absence of simulated firing treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.64-71
• /
• 2005

In this study, we attempted to apply ultrasonic treatment for the preservative treatment of two softwood species, Korean pine and Japanese red pines to evaluate its effectiveness. Wood samples were submerged in oilborne preservative, copper naphthenate (NCU) and waterborne preservative, alkyl ammonium compound (AAC) and then treated with ultrasonic wave of 40 kHz, 400 W. After the treatment, the retention and penetration depth of these preservatives in the specimens were measured as a function of treatment time. Both the retention and penetration depth were continuously increased with increasing the treatment time up to 120 hours, where the retention reached about 95% by the application of AAC and the penetrating depth of 95% and 83% by the application of NCU, respectively for both species. The results of electronic microscopic observation showed that the improved retention capacity could be attributed to air deflation, wood extractive deflation working of ultrasonic wavelength, and destruction of wood pits which served as the pathway of preservatives. The results suggested that the use of ultrasonic treatment could be applied to thick wood veneers for the production of laminated wood products.