• 한국가구학회지
• /
• 제10권2호
• /
• pp.29-36
• /
• 1999

During a radio-frequency/vacuum plus press drying process of some hardwood veneers for decoration we investigated the effect of a grain and thickness of a veneer sheet on drying rates, variations of final moisture content within a bundle of veneer sheets, and formation of checking, end waving, and burning mark. About thirty three hundreds sheet of veneer could be dried in sixty five hours from green to in0-use moisture content, and a final moisture content was significantly effected by initial moisture content of veneer. There were nearly variations in a final moisture content among the veneer sheets in the same bundle. A checking was never found in a edge-sliced veneer, and very slight in a flat-sliced veneer of ash and red oak. There were no end waving and no burning mark in all veneer sheets.

• 공업화학
• /
• 제18권2호
• /
• pp.194-198
• /
• 2007

실온에서 베니어에 ammonium chloride, ammonium sulfate, monoammonium phosphate, 그리고 diammonium phosphate와 같은 암모늄염으로 도포하고, 도포된 베니어의 물리적 성질과 가연성을 조사하였다. 암모늄염로 처리된 베니어의 가연성을 평가하기 위해서, ISO 5660-1 표준에 따른 콘칼로리미터를 이용하여 베니어의 열방출율을 측정하였다. 암모늄염으로 도포된 베니어판은 미처리된 순수 베니어판에 비하여 가연성을 감소시켰다. 도포된 베니어의 flashover 가능성은 R. V. Petrella에 의한 분류 방법에 따라서 착화시간과 최대열방출율을 이용하여 시험하였다. 비중측정 결과 ammonium sulfate로 처리한 베니어의 비중만 미처리 베니어보다 더 높았다. 또한 암모늄염으로 도포된 베니어는 무처리된 순수 베니어보다 낮은 평형함수율을 보였다.

• Journal of the Korean Wood Science and Technology
• /
• 제8권2호
• /
• pp.6-8
• /
• 1980

일본 잎갈나무, 삼나무, 편백의 로타리단판 절삭 적정 노스바압축도를 얻기 위해서 노스바압축도 5%, 10% 15%의 조건으로 절삭된 단판의 이활, 인장 강도를 시험하여 다음과 같은 결론을 얻었다. 1. 일본잎갈나무 2mm단판의 적정 노스바압축도는 15%이었고, 2. 삼나무 2mm 단판의 적정 노스바압축도는 5%이었으며, 3. 편백 2mm 단판의 적정 노스바압축도는 15%이었다.

• Journal of the Korean Wood Science and Technology
• /
• 제44권3호
• /
• pp.415-423
• /
• 2016

원통형 단판적층재는 단판 테이프를 원형 실린더에 감아서 제작된 제품이다. 단판 테이프는 단판을 직사각형으로 제단한 후 섬유 수직방향으로 재봉하여 제작하였다. 단판의 수종과 재봉사의 종류 및 재봉사의 조합을 다르게 제작한 단판테이프로 인장강도 실험이 실시되었다. 라디에타 소나무 단판에 강화 재봉사를 사용하여 재봉선 3줄로 제작한 단판 테이프의 인장강도 성능이 가장 우수하였다. 또한 단판 테이프의 이격 및 끊어짐 현상이 개선되어 원통형 단판 적층재의 작업성이 향상되었다. 원통형 단판적층재는 단판 테이프의 종류와 직물형 유리섬유의 보강 유무 및 단판 적층 수를 다르게 제작하여 낙엽송 원목과 휨강도 성능을 비교 검토하였다. 직물형 유리섬유를 체적비 11%로 보강한 시험편은 휨 파괴계수가 보강하지 않은 시험편보다 65% 향상되었다. 재봉선 2줄 단판 테이프로 제작한 원통형 단판적층재는 단판 테이프 간 Butt joint에서 파단이 발생하였다. 하지만 재봉선 3줄 단판 테이프로 제작한 원통형 단판적층재는 섬유방향으로 파단이 발생하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권1호
• /
• pp.34-47
• /
• 1996

Veneers of two nominal thicknesses, 1.5 and 2.5mm, were rotary peeled from Japanese larch (Larix leptolepis). Dahurian larch (Larix gmelinei) and Radiata pine (Pinus radiata) bolts unheated and heated in the water vat temperature of $66^{\circ}C$ by rising a final temperature at 10cm core of $60^{\circ}C$ to remain core diameter of 11.4cm. 1.5 and 2.5mm thick veneer cut from the heated Japanese larch were significantly thinner than those of the unheated bolt and 2.5mm thick veneer cut from the heated Dahurian larch were significantly thicker than that of the unheated bolt. 1.5mm thick Dahurian larch veneer and 1.5 and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts, respectively. Check distance on the loose side of 1.5mm thick veneer cut from the heated Radiata pine was significantly wider than that of the unheated bolt. However check distances on the loose side of 1.5 and 2.5mm thick Japanese larch and Dahurian larch veneers and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts. Also the depth of check on the loose side of three species showed insignificantly difference between the unheated and heated bolts. Arithmatic mean deviation($R_a$) and maximum height($R_{max}$) of the profile on the loose side of dried veneer by preheating the bolt compared with unheated bolts were different among apecies and between veneer thickness. The preheating treatment slightly affected qualities of these thin veneers such as 1.5 and 2.5mm. The yield of 2.5mm thick veneer from the heated radiata pine was significantly higher than that of the unheated bolt. However the yield of 2.5mm thick veneer for other two species and 1.5mm thick veneer for three species showed insignificant difference between the unheated and heated bolts. The yield of 2.5mm thick veneer for three species were higher than those of 1.5mm thick veneer. The average yields of green veneer of Japanese larch. Dahurian larch and Radiata pine were 57.1, 55.1 and 54.0 percent, respectively. Variables such as initial MC. drying time and veneer thickness had strong effect for Japanese larch veneer, less effect for Radiata pine veneer and nuch less effect on final MC for Dahurian larch veneer in jet drying. Correlation between the current MC and the drying time of Dahurian larch with low variation of initial MC was higher than those of Japanese larch and Radiata pine veneer with high variation of initial MC in high temperature drying. Thickness shrinkages of 2.5mm thick veneer for Japanese larch and Radiata pine were higher than those of 1.5mm thick veneers, but shrinkages of Dahurian larch veneer were similar between two nominal veneer thicknesses.

• Journal of the Korean Wood Science and Technology
• /
• 제22권3호
• /
• pp.17-25
• /
• 1994

This study was carried out to compare the properties of Com-Ply Boards with those of OSBs. These two kinds of boards were made of same flakes. Com-Ply Boards were covered with three different thickness veneers, such as 4mm, 3mm, and 2.5mm. All manufactured Com-Ply Boards and OSBs were 12mm thick. In MOR, all Com-Ply Boards were higher than OSB, and especially 3mm-veneer and 2.5mm-veneer Com-Ply Board were highest. But OSB showed 420kg/$cm^2$. 3mm-veneer Com-Ply Board showed the highest internal bonding 7.0kg/$cm^2$ and then 2.5mm-veneer showed 6.8kg/$cm^2$, and OSB showed 6.6kg/$cm^2$. Screw holding strength showed the high value 23.9kg/$cm^2$, 25.5kg/$cm^2$, and 29.3kg/$cm^2$ respectively at 3mm-veneer, 2.5mm-veneer Com-Ply Board and OSB. Thickness swelling of Com-Ply Boards was lower than that of OSB, but Water absorption of OSB was lower. Finally it was very encouraging that all properties of OSB without veneer, whose cost is higher than flake and whose properties is better, were not worse than those of Com-Ply Board with veneer. It seems That more researches on OSB will be required.

• The Journal of Advanced Prosthodontics
• /
• 제11권5호
• /
• pp.297-304
• /
• 2019

PURPOSE. This in vitro study investigated the repair bond strength of the zirconia ceramic after different aging conditions. MATERIALS AND METHODS. In order to imitate the failure modes of veneered zirconia restorations, veneer ceramic, zirconia, and veneer ceramic-zirconia specimens were prepared and were divided into 4 subgroups as: control ($37^{\circ}C$ distilled water for 24 hours ) and 3000, 6000, 12000 thermal cycling groups (n=15). Then, specimens were bonded to composite resin using a porcelain repair kit according to the manufacturer recommendation. The repair bond strength (RBS) test was performed using a universal testing machine (0.5 mm/min). Failure types were analyzed under a stereomicroscope. Two-way ANOVA and Bonferroni test were used for statistical analysis. RESULTS. The RBS values of zirconia specimens were statistically significant and higher than veneer ceramic and veneer ceramic-zirconia specimens in control, 3000 and 6000 thermal cycling groups (P<.05). When 12000 thermal cycles were applied, the highest value was found in zirconia specimens but there was no statistically significant difference between veneer ceramic and veneer ceramic-zirconia specimens (P>.05). Veneer ceramic specimens exhibited cohesive failure types, zirconia specimens exhibited adhesive failure types, and veneer ceramic-zirconia specimens exhibited predominately mixed failure types. CONCLUSION. Thermal cycling can adversely affect RBS of composite resin binded to level of fractured zirconia ceramics.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.439-443
• /
• 2004

In this research, we describe the sorting conditions modeling by friction force. As in any mechanism which is required to provide good dynamic performance and high accuracy, performance evaluation of optimal control. To understand friction it is necessary to investigate the topography of the sliding surfaces in contact. Any surfaces, even apparently smooth surfaces, are microscopically rough. When two surfaces come into contact, the true contact takes place only at point where asperities come together. The sorting conditions of sorting mechanism with friction force is sorting force must be equal with force can sorting one highest veneer among loaded veneer. This is just a thing being sorted veneer have friction with under veneer and this friction disturb sorting at the same time. Hence, the sorting conditions evaluation is important to sorting one veneer must get under control friction with veneer.

• Structural Engineering and Mechanics
• /
• 제38권1호
• /
• pp.99-123
• /
• 2011

Brick veneer over steel stud backup wall is lighter and easier to construct compared to brick veneer over concrete masonry backup wall. However, due to the relatively low stiffness of the steel stud backup, the brick veneer tends to crack under wind load. This paper briefly introduces a new panelized brick veneer with steel frame backup wall system that is developed to potentially address this problem. The experimental study of the performance of this system under simulated wind loading is discussed in detail. The test setup details and the test specimens are introduced, results of major interests are presented, and performance of the new system is evaluated based on the test results.

• Journal of the Korean Wood Science and Technology
• /
• 제38권5호
• /
• pp.385-390
• /
• 2010

This study was carried out to manufacture very thin natural elm veneer overlaid charcoal board for enhancing aesthetic value of charcoal board for the indoor application, and to use the advantageous properties of the charcoal as a building material for solving the sick house problem. The thin elm veneer had 26.9% opening ratio. The experiment results showed that the spreading area and the nonvolatile content of adhesive did not affect the gas adsoprtion of fancy veneer overlaid charcoal board. The natural thin elm veneer overlaid charcoal board enhanced not only the aesthetic beauty but also showed the same gas adsorption by the charcoal board.