• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.756-758
• /
• 2003

In the machine tool industry, direct drive linear motor technology is of increasing interest as a means to achieve high acceleration, and to increase reliability. This paper deals with the characteristics of tubular type linear oscillating actuator with Halbach magnet array. The magnetic field solutions are derived analytically in terms of vector potential, two dimensional cylindrical coordinate system and Maxwell's equations. Motor thrust, flux linkage, back emf are then derived. The results are shown in good conformity with those obtained from the commonly used finite element method. Test results such as thrust measurements are also given to confirm the analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1017-1019
• /
• 2005

This paper deals with tubular type linear oscillatory actuator with axially magnetized permanent magnet. The magnetic field distribution is predicted using a two-dimensional analytical solution derived in terms of magnetic vector potential and cylindrical coordinate system. Using this result, trust and flux linkage and back emf are derived. The results of predictions from the analysis are compared with corresponding finite element method.

• 한국정밀공학회지
• /
• 제5권1호
• /
• pp.71-77
• /
• 1988

This study applies dynamic deformation analysis to the rake face stress distribution of cemented carbide cut-off tools by turning, using a finite element method. The results are following: 1. The dynamic loaded state of a cut-off tool was very changeable for the first 0.6 seconds. Reaching the normal state, it became in active. 2. Chipping was influnced not only by the magnitude of stress but also by the abrupt change of tensile and compressive stresses. 3. The distribution chat of principal stress by dynamic load and the direction of resultant vector were almost constant regardless of load time.

• Current Optics and Photonics
• /
• 제6권2호
• /
• pp.129-136
• /
• 2022

We propose a photonic crystal fiber (PCF) with a slotted porous core and elliptical-hole cladding, for high birefringence in the terahertz regime. Asymmetry in the guided mode is obtained mainly by using arrays of elliptical air holes in the TOPAS^® polymer cladding. We investigate the tradeoff between several structural parameters and find optimized values that can have a high birefringence while satisfying the single-mode condition. The optical properties in the terahertz regime are thoroughly analyzed in numerical simulations, using a full-vector finite-element method with the perfectly-matched-layer condition. In an optimal design, the proposed photonic crystal fiber shows a high birefringence of 8.80 × 10^-2 and an effective material loss of 0.07 cm^-1 at a frequency of 1 THz, satisfying the single-mode-guidance condition at the same time. The proposed PCF would be useful for various polarization-management applications in the terahertz range.

• 한국전산구조공학회논문집
• /
• 제28권1호
• /
• pp.63-69
• /
• 2015

본 연구에서는 페이즈 필드법을 기반으로 하는 위상 최적설계 방법을 통하여 적외선 스텔스 효과를 위한 적외선 반사층의 설계를 진행하였다. 이를 위하여 수직으로 입사하는 적외선 파를 반사층에서 반사되어 원하는 방향으로 전파되도록 모델링을 하였다. 전파 방향에 측정 영역을 설정하여 해당 영역에서의 목적함수 값을 최대화하도록 설계가 진행되었으며, 이때 목적함수는 전자기파의 에너지 흐름을 나타내는 포인팅 벡터(Poynting vector)로 설정하였다. 페이즈 필드법 기반의 방법에서의 여러 파라미터 값들을 변경해 가며 설계 결과를 도출하였고, 목적함수 값을 최대화하는 모델을 최적 모델로 선정하였다. 선정된 최적 모델에서 gray scale을 cut-off 방법으로 제거한 경우 더 좋은 결과를 얻을 수 있었다. 또한 중적외선 영역에서의 효과를 고려하기 위하여 입사되는 파장을 바꿔가며 얻은 해석결과를 검토하였다. 본 연구의 유한요소해석 및 최적화 과정은 상용 프로그램인 COMSOL과 Matlab을 연동하여 수행하였다.

• Interaction and multiscale mechanics
• /
• 제1권2호
• /
• pp.211-230
• /
• 2008

Owing to the growing size of the eigenvalue problem and the growing number of eigenvalues desired, solution methods of iterative nature are becoming more popular than ever, which however suffer from low efficiency and lack of proper convergence criteria. In this paper, three efficient iterative eigenvalue algorithms are considered, i.e., subspace iteration method, iterative Ritz vector method and iterative Lanczos method based on the cell sparse fast solver and loop-unrolling. They are examined under the mode error criterion, i.e., the ratio of the out-of-balance nodal forces and the maximum elastic nodal point forces. Averagely speaking, the iterative Ritz vector method is the most efficient one among the three. Based on the mode error convergence criteria, the eigenvalue solvers are shown to be more stable than those based on eigenvalues only. Compared with ANSYS's subspace iteration and block Lanczos approaches, the subspace iteration presented here appears to be more efficient, while the Lanczos approach has roughly equal efficiency. The methods proposed are robust and efficient. Large size tests show that the improvement in terms of CPU time and storage is tremendous. Also reported is an aggressive shifting technique for the subspace iteration method, based on the mode error convergence criteria. A backward technique is introduced when the shift is not located in the right region. The efficiency of such a technique was demonstrated in the numerical tests.

• 전기학회논문지
• /
• 제61권8호
• /
• pp.1115-1122
• /
• 2012

This paper analyzes eddy-current loss induced in magnets of surface-mounted permanent magnet (SPM) machines by using an analytical method such as a space harmonic method. First, on the basis of a two-dimensional (2D) polar coordinate system and a magnetic vector potential, the analytical solutions for the flux density produced by armature winding current are obtained. By using derived field solutions, the analytical solutions for eddy current density distribution are also obtained. Finally, analytical solutions for eddy current loss induced in rotor magnets are derived by using equivalent electrical resistance calculated from magnet volume and analytical solutions for eddy-current density distribution. In particular, the influence of time harmonics in armature current on the eddy current loss is fully investigated and discussed. All analytical results are validated extensively by finite element analysis (FEA).

• 해양환경안전학회지
• /
• 제27권1호
• /
• pp.193-200
• /
• 2021

본 연구에서는 국부 비선형 정적 해석을 효율적으로 수행하기 위하여 강성응축(Static condensation)을 활용한 해석기법을 제시하였다. 강성응축기법은 자유도 기반의 유한요소 모델 축소기법이며, 해석 모델을 관심 대상(Target) 부분과 응축되어 생략될(Omitted) 부분으로 구분한다. 본 연구에서는, 관심 대상 부분에는 비선형 영역, 생략될 부분에는 선형 영역으로 지정하였고, 선형 영역에 대응되는 강성 행렬 및 하중 벡터를 비선형 영역, 즉 관심 대상 부분으로 모두 응축하였다. 모델 응축 후에는 비선형 영역에 대한 강성 행렬 및 하중 벡터만으로 이루어진 축소 모델을 구성하였으며, 이 축소 모델만을 뉴턴-랩슨 반복(Newton-Raphson iteration)을 통해 갱신하여 효율적으로 비선형 해석을 수행하였다. 끝으로, 제안된 기법을 다양한 수치 예제에 적용하여 해석기법의 효율성과 신뢰성을 제시하였다.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1025-1034
• /
• 2015

This paper presented an improved analytical method for calculating the open-circuit magnetic field in the surface-mounted permanent magnet machines accounting for slots and eccentric magnet pole. Magnetic field produced by radial and parallel permanent magnet is equivalent to that produced by surface current according to equivalent surface-current method of permanent magnet. The model is divided into two types of subdomains. The field solution of each subdomain is obtained by applying the interface and boundary conditions. The magnet field produced by equivalent surface current is superposed according to superposition principle of vector potential. The investigation shows harmonic contents of radial flux density can be reduced a lot by changing eccentric distance of eccentric magnet poles compared with conventional surface-mounted permanent-magnet machines with concentric magnet poles. The FE(finite element) results confirm the validity of the analytical results with the proposed model.

• Nuclear Engineering and Technology
• /
• 제52권4호
• /
• pp.846-855
• /
• 2020

A loose part monitoring system is used to detect unexpected loose parts in a reactor coolant system in a nuclear power plant. It is still necessary to develop a new methodology for the localization and mass estimation of loose parts owing to the high estimation error of conventional methods. In addition, model-based diagnostics recently emphasized the importance of a model describing the behavior of a mechanical system or component. The purpose of this study is to propose a new localization and mass-estimation method based on finite element analysis (FEA) and optimization technique. First, an FEA model to simulate the propagation behavior of the bending wave generated by a metal sphere impact is validated by performing an impact test and a corresponding FEA and optimization for a downsized steam-generator structure. Second, a novel methodology based on FEA and optimization technique was proposed to estimate the impact location and mass of a loose part at the same time. The usefulness of the methodology was then validated through a series of FEAs and some blind tests. A new feature vector, the cross-correlation function, was also proposed to predict the impact location and mass of a loose part, and its usefulness was then validated. It is expected that the proposed methodology can be utilized in model-based diagnostics for the estimation of impact parameters such as the mass, velocity, and impact location of a loose part. In addition, the FEA-based model can be used to optimize the sensor position to improve the collected data quality in the site of nuclear power plants.