• Journal of the Korean Wood Science and Technology
• /
• 제33권4호통권132호
• /
• pp.15-22
• /
• 2005

현악기용 도료가 현악기의 음향성능에 미치는 영향을 조사하기 위해 음향분석장치(FFT)와 점탄성 분석장치(DMTA, dynamic mechanic thermal analyzer)를 이용하여 목재악기용 도료의 음향적 성능을 평가하였다. 목재악기용으로 사용된 도료는 악기용 우레탄계 상도도료, 오일 스테인계 도료, 천연바니쉬, 캐슈 도료 및 자외선 경화형 에폭시 도료를 사용하였다. 형성된 도막의 음향적인 특성은 FFT 분석기에서 측정된 공명주파수와 댐핑값(damping factor)과 DMTA에서 측정된 tan ${\delta}$를 통하여 유추하였다. FFT에서 측정된 공명주파수와 댐핑값으로부터 도막이 가지는 음향특성에 대해 분석하였다. 측정된 도막의 점탄성적인 특성과 음향적 특성을 검토한 결과 악기용으로서의 적정도료를 결정하였다.

• The Journal of Advanced Prosthodontics
• /
• 제7권4호
• /
• pp.323-328
• /
• 2015

PURPOSE. This in-vitro study was designed to evaluate retention forces, microleakage and plastic deformation of a prefabricated 2-implant bar attachment system (SFI-Bar, Cendres+$M{\acute{e}}taux$, Switzerland). MATERIALS AND METHODS. Two SFI implant-adapters were torqued with 35 Ncm into two implant analogues. Before the tube bars were finally sealed, the inner cavity of the tube bar was filled with liquid red dye to evaluate microleakage. As tube bar sealing agents three different materials were used (AGC Cem (AGC, resin based), Cervitec Plus (CP; varnish) and Gapseal (GS; silicone based). Four groups with eight specimens each were tested (GS, GS+AGC, AGC, CP). For cyclic loading, the attachment system was assembled parallel to the female counterparts in a chewing simulator. The mean retention forces of the initial and final ten cycles were statistically evaluated (ANOVA, ${\alpha}{\leq}.05$). RESULTS. All groups showed a significant loss of retention forces. Their means differed between 30-39 N initially and 22-28 N after 50,000 loading cycles. No significant statistical differences could be found between the groups at the beginning (P=.224), at the end (P=.257) or between the loss of retention forces (P=.288). Microleakage occurred initially only in some groups but after 10,000 loading cycles all groups exhibited microleakage. CONCLUSION. Long-term retention forces of the SFI-Bar remained above 20 N which can be considered clinically sufficient. The sealing agents in this study are not suitable to prevent microleakage.

• Tribology and Lubricants
• /
• 제33권2호
• /
• pp.37-44
• /
• 2017

A DE-side LBP tilting pad journal bearing of a 1-stage overhung heat-pump compressor in a propylene process exhibited abnormal high-temperature behavior. Its temperature had been relatively high at $78^{\circ}C$ from the beginning of operation. In 2014, after three years of operation, it increased suddenly and reached $103^{\circ}C$. Installing a varnish removal equipment and others managed to stabilize the temperature at $95^{\circ}C$. We undertook a troubleshooting approach for reviewing the comprehensive status and integrity of the temperature design of the bearing. We performed lubrication and heat-balance analysis, based on the design engineering data and documents supplied by the OEM. For the base design data of DE-side TPJB, evaluating the effects of key design variables on bearing metal temperature showed that firstly, increasing the bearing clearance and supply oil flow-rate, and next, changing the oil type, and finally, increasing the machined pad clearance and offset, are more effective in reducing the bearing metal temperature. Furthermore, a clarification meeting with the OEM revealed that an incorrect decision had been made to decrease the bearing clearance to eliminate the SSV harshness issue, while not maintaining a sufficient oil flow-rate. We conducted a detailed retrofit design analysis, wherein we increased the oil flow-rate and bearing clearance by decreasing the preload. We predicted that the bearing temperature would decrease to $63^{\circ}C$ from $75.7^{\circ}C$ even at the rerate condition. Finally, after installing and operating a retrofit replacement bearing in 2015, the bearing temperature stabilized at a low temperature of $65^{\circ}C$. Currently (January. 2017), two year later, the bearing metal temperature remains at $65^{\circ}C$. Therefore, we can conclude that the abnormal high-temperature behavior of the bearing has been resolved completely.

• Restorative Dentistry and Endodontics
• /
• 제18권2호
• /
• pp.277-290
• /
• 1993

Dental caries is considered to be caused by demineralization by organic acid produced by microorganism. But the formation of subsurface lesion in initial caries make it diffcult to explain by simple demineralization. This study is carried out on the basis of thermodynamic concept proposed by Margolis and Moreno. The purpose of this study is to evaluate the effects of acid concentration and pH of lactate buffer system on the artificial caries lesion progress. 160 teeth without any crack, defect or opaque enamel were used and coated with nail varnish except the window ($2{\times}3$ mm). Under the constant degree of saturation(D.S.). The teeth were divided into 8 groups according to acid concentration(10mM, 25mM, 50mM, 100mM) and pH(4.3, 5.0, 6.0). Each group was immersed in buffer solution for 3, 6, 9, 18 days under controlled temperature($25^{\circ}C$). After cutting through the window and grinding, the specimens, 100-150 um in thickness, were imbibed in water or air and examined using polarilizing microscope. The depth of the surface and subsurface surface lesion were measured. 1. In the constant pH and D. S. value, the subsurface lesion progresses more rapidly as the concentration of lactic acid increases. (0.01, 0.025, 0.05, 0.1) 2. In the constant acid concentration and DS value, the subsurface lesion progresses more slowly as the pH increases. (4.3, 5.0, 5.5, 6.0) 3. The width of surface lesion seems to be constant independant of pH and acid concentration.

• Restorative Dentistry and Endodontics
• /
• 제22권1호
• /
• pp.447-463
• /
• 1997

The purpose of this study was to evaluate the effectiveness of copal varnish and five bonding agents(Scotchbond Multi-Purpose Plus Dental Adhesive System, Panavia 21, All Bond 2, Superbond D-Liner II plus, Fuji Duet) in reducing microleakage under amalgam restorations. Class V cavity were prepared on both buccal and lingual surface of sixty extracted human molars with cementum margin and were filled with different kinds of liners and amalgam. All teeth were stored at $37^{\circ}C$ in physiologic saline solution. After 1 week they were thermally stressed for 500 cycles between 5 and $55^{\circ}C$ in baths containing 0.5 % basic fuchsin dye. The dye penetrations were observed with a stereomicroscope. Scanning electron micrographs were taken of representative tooth sections from each group to assess the nature of the tooth/liner/amalgam interface. The statistical test were applied to the results using a one way analysis variance (ANOVA) and Duncan's multiple range test. The results were as follows ; 1. In all groups, the enamel margin showed significantly lower leakage value than the cementum margin (p<0.05). 2. At the dentin and enamel margins, the leakage value of Copalite-lined group showed significantly higher than that of no liner group (p<0.05), but showed significantly lower than that of bonding agent lined-groups (p<0.05). 3. There was no significant difference between the bonding agent lined-groups (p>0.05). 4. On the backscattered scanning electron microscopy observation, discontinuous gaps were observed between amalgam and dentin in the bonding agent-lined amalgam restorations and the bonding agents appeared to fill the gap space and were mixed with amalgam particles. At the amalgam/tooth interface, unsealed dentin and continuous gaps were found in both unlined and Copalite-lined restorations.

• 한국가구학회지
• /
• 제26권2호
• /
• pp.122-129
• /
• 2015

In previous study, VOC emission characteristics of coating materials for wood finishing were conducted and results showed that eco-friendly products has about 15~46% lower TVOC emission than typical products. In this study, lower TVOC emitted coating materials were applied on pine and then changes of VOC emission characteristics from pine with treatments were determined. Non-treated pine emitted $604.7{\mu}g/m^2h$ of TVOC that contained 66% of NVOC ($399.7{\mu}g/m^2h$). However, $V_2$ finished pine showed no NVOC emission rather than AVOC emission that consisted of Toluene, Ethylbenzene, m,p-Xylene, o-Xylene, 1,2,4- Trimethylbenzene. All coating materials inhibited ${\alpha}$-Pinene emission which originally from pine, but waterborne stain ($W_1$ and $W_3$) showed lower disruption of that emission. Moreover, $W_3$/wood showed higher NVOC emission such as ${\alpha}$-Terpinol, Terpinen-4-ol which are known as antioxidant substrates. Based on results, VOC emission characteristic of pine was significantly affected by coating materials with negatively in terms of ${\alpha}$-Pinene emission or positively in terms of NVOC emission. Therefore, coating material is important factor for indoor air quality when it would apply on wood products. For the future study, VOC emission characteristic of coated wood will be conducted continuously.

• Restorative Dentistry and Endodontics
• /
• 제26권5호
• /
• pp.379-386
• /
• 2001

This study was performed to evaluate the sealing ability of various retrograde filling materials by using bacterial penetration and dye penetration test. One hundred and forty extracted human teeth with single, straight canals and mature apiece were collected and used for this study. All canals were instrumented using an engine driven Ni-Ti file (ProFile). After removing 3mm from the apex of tooth, a standardized 3mm root end cavity was prepared using an ultrasonic instrument. The 70 teeth were randomly divided into 7 groups : 6 groups for retrograde filling using Super-EBA, ZOE, Chelon-Silver, IRM, ZPC and amalgam. The 7th group was used as a negative control. Nail varnish was applied to all external root surfaces to the level of the reseated root ends to prevent lateral microleakages. The specimens were then sterilized in an ethylene oxide sterilizer for 24 hours. 2 mm of the reseated root was immersed in a culture chamber containing a Tripticase Soy Broth with a phenol red indicator. The coronal access of each specimen was inoculated every 72 hours with suspension of Proteus vulgaris. The culture media were observed every 24hours for color change indicating bacterial contamination. The specimens were observed for 4weeks. The remaining 70 teeth were submitted to a dye penetration test. The canals of all teeth were first sealed with AH26 and obturated using an Obtura II system. Root resection, root end preparation and retrograde filling was performed as above. All specimens were suspended in 2% methylene blue dye for 72 hours before being ion gitudinally split. The degree of dye penetration was then measured using a stereomicroscope at 10 magnification and evaluated. The results were as floows : 1. In the bacterial penetration, the degree of leakage was the lowest in the Super-EBA, followed by, in ascending order, ZOE, Chelon-Silver IRM and ZPC. The amalgam showed highest bacterial leakage of all(p<0.01). 2. In the dye penetration, the degree of microleakage was the lowest in the Chelon-Silver and Super-EBA, followed by, in ascending order, IRM, ZPC. The ZOE and amalgam showed the highest microleakage of all (p<0.05). These results suggested that the eugenol based cement, Super-EBA, have excellent sealing ability as a retrograde filling material.

• 청정기술
• /
• 제13권1호
• /
• pp.22-27
• /
• 2007

옻은 전통적으로 옻칠로서 사용되었으며, 최근 많은 연구를 통하여 과학적으로 그 내구성, 항균성들이 밝혀졌기 때문에 본 연구진은 옻이 최근 대두되고 있는 친환경적 방오도료의 문제를 해결할 수 있을 것으로 예상하고 있다. 따라서 본 실험에서는 옻의 주성분인 urushiol을 화학적으로 합성하고, 그 유도체들과 함께 어느 정도의 항균효과가 있는지 알아보았다. 그 결과, 본 연구진은 합성된 urushiol이 뛰어난 항진균효과를 가짐을 알 수 있었고, 항균효과 측면에서는 그람양성균에는 좋은 효과를 보인 반면 그람음성균에서는 큰 효과를 보이지 않음을 알 수 있었다. 또한 urushiol과 그 유도체들의 항균력은 균주에 따라 서로 다른 특이적 항균성을 보이는 것을 알 수 있었다.

• Nuclear Engineering and Technology
• /
• 제4권4호
• /
• pp.331-339
• /
• 1972

트리티움 표지 형광도료의 원료인 고 비방사능의 트리티움 표지 폴리스타이렌을 얻기 위하여 테슬라 방전법, 윌즈바크 노출법, 감마선 조사법, 자외선 조사법 등 여러 방법들을 비교 검토하였다. 테슬라 방전 또는 자외선 조사법으로 얻은 polystyrene-T(G)의 비방사능은 1-l.2mCi/mg로써 다른 방법에 의한 생성물의 값보다 높았다. Polystyrene-T(G)와 ZnS:Cu 형광체를 무게비로 1:4가 되게 혼합하면 광도가 가장 컸다. 30mg의 형광도료 혼합물을 1ml의 바인다(시판 니스 1g을 100m1의 벤젠에 녹인 것)를 써서 바르는 경우 최대 장도는 약 20$\mu$L이었으며 갱내 표지판이나 암실내 광원으로 유효하게 사용될 수 있음을 확인하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제27권3호
• /
• pp.31-38
• /
• 1999

본 연구는 재면이 약한 낙엽송재의 교실용 마루판으로의 재질개량의 일환으로 경도와 내마모성 등 표면성능의 개선을 도모하기 위한 표면강화처리기술을 개발하기 위하여 수행되었다. 낙엽송 마루판의 밑칠을 폴리우레탄 우드실러, 중간칠을 폴리우레탄 샌딩실러도료로 도장한 다음, 마감칠로써 자외선 (UV) 경화형 에폭시아크릴레이트수지도료와 우레탄아크릴레이트수지도료를 이용한 표면강화처리에 의해 경도, 내마모성, 부착성, 내충격성이 향상되었다. 이 처리에 의해 브리넬경도가 1.75에서 2.25~2.27로 개선되어 2.38의 참나무재와 유사한 경도치를 나타내었으며, 약 2배의 내마모성 증대효과가 나타났다. 외부충격에 의한 도막의 갈라짐은 거의 발생하지 않았으며, 에폭시아크릴레이트가 우레탄아크릴레이트에 비해 충격에 의한 크랙의 발생율이 적었다.