• 설비공학논문집
• /
• 제5권4호
• /
• pp.249-256
• /
• 1993

Numerical method is applied to predict the time variation behavior of flammable mixture formation in a two dimensional enclosure from the beginning of gas leak. Additionally experimental method is used to consider qualitative aspects. Characteristics of flammable mixture formation such as distribution of flow and fuel mass fraction at various locations in the enclosure are determined for the following parameters: the various locations of leak at the bottom and aspect ratio of the enclosure. In the case of gas leak with small leak velocity from the bottom of enclosure gravitational force affects the formation of flammable mixture. Aspect ratio of the enclosure also affects the formation of flammable mixture. The volume of the region of recirculating flow is dominant factor affecting the formation mixture.

• 통합자연과학논문집
• /
• 제14권3호
• /
• pp.99-106
• /
• 2021

A mixture of alcohol and water is commonly used as antifreeze, liquor, and the fundamental solvents for the manufacture of cosmetics, pharmaceuticals, and inks in our daily life. Since various properties of alcohol water mixtures such as density, boiling or melting point, viscosity, and dielectric constant are determined by their mixing ratio, it is very important to know the mixing ratio to predict their properties. One of simple method to find the mixing ratio is measuring the density of the mixtures. However, it is not easy to predict the mixing ratio from the density of the mixtures because the relationship between mixing ratio and density has not been established well. The relationship is dependent on the relative sizes of solute and solvent molecules, and their interactions. Recently, an empirical model to predict the density of glycerol water mixture from their mixing ratio has been introduced. The suggested model is simple but quite accurate for glycerol water mixture. In this article, we investigated the applicability of this model to different alcohol water mixtures. Densities for six different alcohol water mixtures containing various alcohols (e.g., ethylene glycol, 1,3-propane diol, propylene glycol, methanol, ethanol, and 1-propanol) were simulated and compared to experimentally measured ones to investigate the applicability of the model proposed for glycerol water mixtures to other alcohol water mixtures. The model predicted the actual density of all alcohol water mixtures tested in this article with high accuracy at various ratios. This model can probably be used to predict the mixing ratio of other alcohol water mixtures from their densities beyond 6 alcohols tested in this article from their densities.

• 한국식품영양과학회지
• /
• 제28권6호
• /
• pp.1212-1219
• /
• 1999

The oils were extracted from the mixture of roasted(for 20 min at 190oC) perilla seeds(RPS) and roasted (commercially) peanuts(RPN) by solvent extraction(SE) and mechanical expression(ME). The effects of mixing ratio on physicochemical characteristics and oxidative stability of their oils were investigated. Yields of both SE and ME oils were increased as the RPN ratio in the mixture increased. In all the SE and ME oils, the major fatty acids were oleic, linoleic and linolenic acid, and total saturated fatty acids increased gradually, but total unsaturated fatty acids decreased gradually as the RPN ratio in the mixture was increased. The specific gravity and refractive index of both SE and ME oils decreased as the RPN ratio in the mixture was increased. Acid value, saponification value and iodine value of SE oils decreased as the RPN ratio in the mixture increased, whereas acid value and iodine value of ME oils decreased and saponification value increased. The colors of ME oils were darker brownish than SE oils. The oxidative stability of SE oils was decreased as the RPN ratio in the mixture increased, whereas that of ME oils was increased. Sensory evaluation of all the oils extracted from the mixture with various mixing ratio showed significant differences in flavor, taste, color and overall acceptance(p<0.01). The oil extracted from the mixture of the mixing ratio of 8:2(RPS:RPN) showed slightly higher preference regardless of extraction method.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.201-209
• /
• 1996

This study describes the combustion characteristics of methance-air mixture with various equivalence retio and initial conditions of mixture in constant volume combustion chamber. Combustion characteristics of methane-air mixture such as combustion pressure, combustion temperature, and heat release were investigated by the measurement of combustion pressure and temperature in the combustion chamber. The results show that maximum combustion pressure, gas temperature and rate of heat release have peaks at equivalence ratio of 1.1. Combustion duration is also the shortest at the equivalence ratio of 1.1 and it is shortened as initial mixture temperature increases.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.48-57
• /
• 2003

A cylindrical constant volume combustion chamber was used to investigate the flow characteristics at spark plug and the combustion characteristics of homogeneous charge methane-air mixture under various initial pressure, excess air ratio and ignition times in quiescent mixture. The flow characteristics such as mean velocity and turbulence intensity was analyzed by hot wire anemometer. Combustion pressure development measured by piezoelectric pressure transducer and flame propagation acquired by ICCD camera were used to investigate the effect of initial pressure, excess air ratio and ignition times on pressure, combustion duration, flame speed and burning velocity. Mean velocity and turbulence intensity had the maximum value at 200 or 300ms and then decreased to near 0 value gradually after 3 seconds. Combustion duration, flame speed and burning velocity were observed to be promoted with excess air ratio of 1.1, lower initial pressure and ignition time of 300ms.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.193-197
• /
• 2008

This study enforced to produce the planting concrete block which could be applied to various slopes economically. First of all, the physical properties was investigated with the various types of aggregate and aggregate ratio of the paste for the lead to mixture proportion of the planting concrete. As a result, the orchid stone as aggregate and 30% of aggregate ratio of the paste were used as the basic mixture proportion considering 20~30% of maintained void ratio for the growth of plant, over 20% of capillary suction for holding water, and 3MPa as the minimum strength. For the result of the test to the new planting block which was quite different from existing planting concrete block, it could complement the problems and be possible to produce effectively and economically because various slopes like 40ﾟ~75ﾟ, continual produce by extrusion, and pumping out were possible were possible.

• Korean Chemical Engineering Research
• /
• 제51권6호
• /
• pp.677-684
• /
• 2013

혼합냉매를 사용하여 천연가스를 액화하는 혼합냉매공정(Mixed refrigerant cycle, MRC)은 공정이 간단하고 장치비가 적게 들며 운전 또한 용이하여 널리 채택되고 있는 공정이다. MRC에서 중요한 기술 중 하나는 혼합냉매를 선택하고 최적의 혼합비를 결정하는 것이다. 본 연구에서는 일반적인 MRC에서 혼합냉매와 혼합냉매의 혼합비가 공정의 성능에 미치는 효과를 살펴보았다. 이를 위해 통계적 기법 중 실험계획법의 하나인 혼합물 설계와 반응 표면법을 이용하여 전체 공정의 에너지 소비가 최소가 되게 하는 최적의 냉매를 선택하고 그 혼합비를 결정하였다. 여러 냉매와 혼합비에 따른 MRC 공정의 모사는 Aspen HYSYS를 사용하였으며 혼합물설계와 반응 표면법은 Minitab을 사용하였다. 연구결과 냉매로는 methane ($C_1$), ethane ($C_2$), propane ($C_3$)과 nitrogen ($N_2$)가 선택되었으며 에너지 소비를 최소화하는 혼합비(몰 비) 또한 구할 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.583-586
• /
• 2005

Strength of concrete is very important factor in design and quality management and may represent overall quality of concrete. Such strength of concrete may differ depending on amount of cement mixed, water and fine aggregate ratio. Classic concrete products have been produced mainly with ordinary portland cement(hereinafter 'cement'), water and fine aggregate as shown above, but various additives and mixture materials have been used for concrete manufacturing, along with development of high functional concrete and diversification of structures. Various kinds of chemical mixtures agents and mixture materials have been used as it requires concretes with other features which cannot be solved with existing materials only, such as high strength, high flexibility and no-separation in the water. Such addition of various mixture agents may cause change in cement hydrate, affecting strength. Hydration of cement is the process of producing potassium hydroxide, C-S-H, C-A-H and Ettringite, while causing heat generation reaction after it is mixed with water, and generation amounts of such hydrates play lots of roles in condensation and hardening. This study aims to analyze its strength and features with hydrates by making specimen according to curing temperature, types of mixture agent, mixing ratio and ages and by analyzing such hydrates in order to analyze role of cement hydrate on early strength of concrete.

• 한국도로학회논문집
• /
• 제20권1호
• /
• pp.97-105
• /
• 2018

PURPOSES : Asphalt concrete pavement is damaged by various causes such as traffic and environmental loads. The distressed pavement should be maintained by various methods to provide a comfortable and safe pavement for the driver. This study evaluates the effect of adding a mixing procedure to enhance the mixture quality in the hot in-placement recycled asphalt pavement method, which is an asphalt-pavement maintenance method. METHODS : Various test methods such as Marshall stability and dynamic stability, were employed to estimate the recycled asphalt mixture with and without an additional mixing, using the hot in-placement recycled asphalt pavement method. RESULTS : The mixture samples used in this study were taken before and after the addition of the mixer in the hot in-placement recycled asphalt pavement method (HIR) at field construction sites in GongJu and JinJu in South Korea. The test results of both mixtures satisfied the asphalt-mixture standard specifications. CONCLUSIONS : This study confirmed that adding a mixer in the HIR method results in a well-mixed new asphalt mixture, rejuvenator, and reclaimed asphalt mixture.

• International Journal of Automotive Technology
• /
• 제6권2호
• /
• pp.79-85
• /
• 2005

This work is to investigate the surface heat flux and combustion characteristics of premixed propane mixture in a constant volume chamber. The experiment of heat flux and combustion characteristics of premixed propane mixture are performed with various equivalence ratio and initial pressure conditions. Based on the experimental results, it is found that the maximum instantaneous temperature is increased with the increase of initial pressure in the chamber. There are significant differences in the burning velocity of premixed propane mixture at different measuring points in the constant volume combustion chamber. A]so, the trends of temperature difference at each measuring points are similar to the burning velocity in the combustion chamber. It is concluded that the total heat loss during the combustion period is affected by the equivalence ratio and the initial condition of fuel-air mixture.