• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1716-1721
• /
• 2006

The Lubrication Mode of line contacts between the vane and the camring in an oil hydraulic vane pump has been investigated. First, the variations of the radial force of a vane were calculated from previous measurements of dynamic internal pressure in four chambers surrounding a vane. Next, the lubrication modes were distinguished with Hooke's chart, which is an improvement over Johnson's chart. Finally, the influence of the boundary conditions in the lubrication region on the fluid film lubrication was examined by calculating the film pressure distributions. The results showed that the lubrication mode of the vane tip exists in the rigid-variable-viscosity region, and that discharge pressure higher than 7 MPa greatly affects the oil film pressure in the small and the large arc section because of the Piezo-viscous effect.

• Journal of Mechanical Science and Technology
• /
• v.19 no.12
• /
• pp.2179-2186
• /
• 2005

The lubrication modes of line contact between the vane and the camring in an oil hydraulic vane pump have been investigated. First, variations of the radial acting force of a vane were calculated from previously measured results of the dynamic internal pressure in four chambers surrounding a vane. Next, distinctions of the lubrication modes were made using Hooke's chart, which represents an improvement over Johnson's chart. Finally, the influence of boundary conditions in the lubrication region on fluid film lubrication was examined by calculating film pressure distributions. The results show that the lubrication modes of the vane tip are a rigid-variable viscosity region. This region discharges pressure higher than 7 MPa, and exerts a great influence on oil film pressure in the large arc section due to the Piezo-viscous effect.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.3 s.246
• /
• pp.230-237
• /
• 2006

Flows in the cavity with pump out vane are calculated using the CFX-Tascflow CFD code. flow calculations are performed for different values of vane height, numbers, leakage flow rate, and rotational speed. The flow is very complex and three dimensional with strong vortex and leakage flow over the vane. The variations of pressure coefficient and K-factor with these parameters and resulting effects on the thrust and torque are studied. The present study contributes to showing the capability of flow simulation of back cavity with pump-out vane. The calculated results are good enough to be used back cavity design.

• Journal of Drive and Control
• /
• v.11 no.1
• /
• pp.14-24
• /
• 2014

Variable displacement vane-type oil pumps represent one of the most innovative pump types for industrial applications, especially for engine lubrication systems. This paper presents a complete and accurate mathematical model for a typical variable displacement vane-type oil pump. Firstly, its theoretical model is revised. Secondly, an analysis of power loss factors of this pump type is carefully investigated to optimize the modeling accuracy. Finally, the estimated pump performance using the complete pump model is verified by numerical simulations in comparison with the practical tests.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1990.06a
• /
• pp.32-44
• /
• 1990

유압 Vane pump는 carming, rotor, vane에 의하여 둘러싸인 공간체적이 rotor의 회전과 함께 변화하면서 pump 작용을 한다. 즉 공간체적이 증가하는 동안은 유압이 저압으로 되어 흡입구에서 유압유를 흡입하고 vane의 존환점 (vane이 가장 많이 출한 점)을 지나면 공간용적이 감소하여 유압류는 고압으로 될 수 있도록 되어있다. 이때 vane은 관성력과 점성력 그리고 유압류의 압력에 의한 힘으로 vane 선단이 캠링의 내면에 밀착되어 회전하도록 되어있다. 유압 vane pump 베인 선단부의 윤활문제와 관련된 지금까지의 연구로서는 Hibi 등에 의한 압력평형형 베인모터, W.D Beck, T.C Edwards에 의한 베인형 콤푸렛셔 Ujiie 등에 의한 베인형 진공펌프, Ueno 등에 의한 가변용량형 베인펌프의 마찰특성에 관한 연구 및 베인 이간 현상에 관한 실험적 연구가 있다. 그러나 이와 같은 연구들의 베인과 캠링 슬라이딩 부분에 관한 취급들은 베인선단 슬라이딩 부분에 가해지는 변동가중이 불명확했기 때문데, 단순히 슬라이딩 부분의 면적이 작다는 이유로 단성유체 윤활상태일 것이라는 확정을 하였을 뿐, 실제적으로 어느 정도의 윤활 상태를 파악하기 위하여 회전하는 vane의 가학적인 거동을 확실하게 규명하고자 함이 본 연구의 목적이다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.206-211
• /
• 1998

This paper presents the deformation characteristics of cam ring in a balanced type vane pump. Cam ring is operated in the condition of high pressure. Therefore the local deformation of cam ring affects the characteristics of compression, vane motion and noise and vibration. We analyzed the deformation of cam ring in three types by using the finite element method. As results of analysis, deformed shape of cam ring and the effects of deformation on the compression are presented.

• Tribology and Lubricants
• /
• v.9 no.1
• /
• pp.45-54
• /
• 1993

The lubrication characteristics of line contacts between the vane and cam ring in an oil hydraulic vane pump with intravanes have been investigated. Variations of the radial acting force of a vane were calculated from previously measured results of dynamic internal pressures in four chambers surrounding a vane, and variations of the film thickness were estimated in both the rotational speed range from 500 to 1500 rpm and in the delivery pressure range from 1 to 14 MPa. The results indicate the variations of the radial acting force and film thickness. It is found that the regimes of lubrication in the vane tip contacts lover rigid-isoviscous to rigidvariable viscosities.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.55-59
• /
• 1989

Measurement of the friction force of vane tip have been made to provide essential information for the study of the pump dynamics, the pump design and the analysis of triboligical problems in the sliding components. The influences of the radial load, rotating speed and frequency of vane on the friction forces of vane tip have been investigated. The results indicated that the friction coefficient of vane tip are affected by the rotating speed remarkably but the effect of acting load on the vane tip and frequency of load are very small. The stribecks diagram shows that the lubrication regime of the sliding point of vane tip is mixing lubrication.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.190-195
• /
• 1998

This paper reports on the theoretical and expetimental study of the vane and cam ring motions in a variable displacement vane pump which is already used widely in various industrial and automotive applications. Dynamic equations of vane and cam ring motion and flow continuity equations are derived and then solved simultaneously using the numerical method. Vane detachment cause the pressure tipples, noise, wear in cam ring, and decrease the volumetric efficiency. Consequently, Vane detachment occurs due to excess compression in the pumping chamber, and it can be reduced by adjustment of design parmeters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.106-114
• /
• 2003

The pressure ripple in the delivery port is caused by flow ripple, which is induced by variation of pumping chamber volume. The other reason is the reverse flow from the outlet volume produced by pressure difference between pumping chamber and outlet volume, when the pumping chamber is connected with the outlet volume. In this study, a mathematical model is presented for analyzing discharge pressure ripple, which includes vane detachment, cam ring movement , and fluid inertia effects in V-groove in the side plate. From the analysis and experiment, it was found that V-groove on the side plate, coefficient of spring supporting the cam ring, and average discharge pressure are the main factors of discharge pressure ripple in variable displacement vane pump. The theoretical results, provided in this study, were well agreed with experimental results. The analytical model to estimate the magnitude of pressure ripple in this study is expected to be used f3r the optimal design of the variable displacement vane pump.