• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.190-195
• /
• 1998

This paper reports on the theoretical and expetimental study of the vane and cam ring motions in a variable displacement vane pump which is already used widely in various industrial and automotive applications. Dynamic equations of vane and cam ring motion and flow continuity equations are derived and then solved simultaneously using the numerical method. Vane detachment cause the pressure tipples, noise, wear in cam ring, and decrease the volumetric efficiency. Consequently, Vane detachment occurs due to excess compression in the pumping chamber, and it can be reduced by adjustment of design parmeters.

• Journal of Drive and Control
• /
• v.10 no.3
• /
• pp.7-13
• /
• 2013

Hydraulic vane pumps are widely used in various hydraulic systems because of its compactness and light weight. It is well known that the vanes and cam ring are separated by very thin liquid films which result in the EHL state. Contrary to the case of cylindrical roller bearings, the inlet and side boundary pressures are much higher than the atmospheric pressure. In this paper, a numerical solution of the EHL of finite line contacts between the cam ring and vane tip with profiled ends is presented. Using a finite difference method with non-uniform grids and the Newton-Raphson method, converged solutions are obtained for moderate load and material parameters. The EHL pressure distribution and film shape are considerably affected by pump delivery pressure and the side boundary condition applied. Both the maximum pressure and the minimum film thickness always occurred near the edge regions. The present results can be used in the design of optimum vane profile in hydraulic vane pump.

• International Journal of Fluid Machinery and Systems
• /
• v.10 no.1
• /
• pp.86-98
• /
• 2017

In order to obtain high efficiency and low resistance droplet separation apparatus, axial vane type gas-liquid separators with different guide vanes were designed, and the RNG $k-{\varepsilon}$ model as well as discrete phase model (DPM) were used to investigate the flow pattern inside the separators. It was shown that the tangential velocity distribution under different guide vanes have Rankine vortex characteristics, pressure distribution exhibits a high similarity which value becomes big as the increase of the blade outlet angle and the decrease of the guide vane numbers. The increase of the guide vane numbers and the decrease of the blade outlet angle could make separation improve significantly. The separation efficiency is almost 100% when the droplet diameter is bigger than $40{\mu}m$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.36-43
• /
• 2012

In this work the mixing and flow characteristics of a vane-type static mixer were investigated numerically for the reduction of NOx in the SCR-system of the diesel engines. The mixer was located in the 57 times pipe diameter away from the inlet. The analysis were performed by changing such various parameters as vane shape, angles, blockage ratio and location of the vane. The flow structure through the mixer was characterized by uniformity index and pressure drop. The results show that uniformity index and pressure coefficient are substantially influenced by the vane shape, angle, blockage ratio and position of the vane of the mixer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.2
• /
• pp.201-206
• /
• 2017

In the study, the inner flow characteristics were analyzed by modifying the inner design parameter of the vane-type vacuum pump. The effect of pressure generated by the inner flow of pump on the rotor and vane was analyzed. The design parameter was analyzed using the angle variation of tilting and rotation of the vane. MRF was used for the analysis conducted using a virtual condition where the rotor and vane are rotated. The pressure gained from the load of the rotor and vane in the flow analysis is used for the structure analysis. Based on the results, the effect of variable vane design was revealed in structural strength. The effect of centrifugal and friction force generated during pump operation on structural strength was also analyzed.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.33-38
• /
• 2010

As for an oil hydraulic vane pump of vehicle hydraulic systems, the highest of planning technique required by the acquisition of optimum profile data which can be available to predict noises and vibrations. Pressure pulsation may result in considerable vibration and noise of pump component as well as cavitation in hydraulic system. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in chamber surrounding a vane have been investigated. It is very important to predict pressure pulsation in vane pump. This paper presents analysis of technique of vane pump for automatic transmission. The predicted result using AMESim model were good agreement with the experimentally obtained results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.2
• /
• pp.163-169
• /
• 2013

In order to make the vertical-axis cross flow wind turbine commercially feasible, a guide vane is adopted and the effect of the guide vane shape is examined in order to improve the wind turbine performance. CFD analysis on the performance and internal flow of the turbine is carried out for the wind turbine model. The result shows that when the guide nozzle is installed, almost over two times of power coefficient are achieved in comparison with the case of no guide nozzle installation. The guide nozzle acts as a role of suppressing the flow resistance at the blade passage, which is found when the guide nozzle is installed. Moreover, in this study, two kinds of the guide vane with a straight type and a curved type are adopted and compared. The curved guide vane nozzle produces higher power coefficient in comparison with that of straight guide vane nozzle.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1819-1824
• /
• 2004

The common method to improve heat transfer in Nuclear fuel rod bundle is install a mixing vane in space grid. The previous split mixing vane is guides cooling water to swirl flow in sub-channel of fuel assembly. But, this swirl flow decade rapidly after mixing vane and the effect of enhancing the heat transfer vanish behind this short region. The large scale secondary vortex flow was generated by rearranging the inclined angle direction of mixing vanes to the coordinated directions. This LSVF mixing vanes generate the most strong secondary flow vortices which maintain about 35 $D_H$ after the spacer grid and the streamwise vorticity in subchannel with LSVF mixing vane sustain two times more than that in subchannel with split mixing vane. The turbulent kinetic energy and the Reynolds stresses generated by the mixing vanes have nearly same scales but maintain twice more than previous type.

• Tribology and Lubricants
• /
• v.10 no.3
• /
• pp.54-61
• /
• 1994

The regimes of elastohydrodynamic lubrication at the points where line contacts occur between the vane tip and camring in an oil hydraulic vane pump is studied. A study of the contact conditions in vane pump provided most of the early interest in the possibility of fluid film lubrication in highly loaded contacts. The variation of viscosity with pressure and the elastic deformation associated with the high pressures generated in the contact region are the major causes of the complexity attributed to lubrication behavior. Therefore a numerical solutions to the problem of elastohydrodynamic lubrication of line contact are obtained by using a finite-difference formulation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.23-23
• /
• 1998

Jet Vane Type 추력방향제어 시스템의 구조적 안정성을 검토하기 위해 시스템의 해석을 Vane, Ablation & Bracket Interface, Nozzle flange & Housing Interface 및 Fastener의 세 부분으로 나누어 수행하였다. 해석을 위한 외력조건은 유동해석을 통해 얻어진 온도 및 압력분포에 근거하였으며, Vane의 응력해석을 위해서는 상용 Software인 Patran 및 Nastran이 사용되었다. 이번 연구는 Test Model 단계로서 충분한 강도의 고정 Housing이 사용되어, 이에 대한 해석은 수행되지 않았지만 추후 Flight Model 단계에서는 함께 고려되어질 것이며, 각 경우의 Margin of Safety값들을 도출하여 구조적 안정성을 검토하였다.