• Journal of the Korean Wood Science and Technology
• /
• v.26 no.3
• /
• pp.1-8
• /
• 1998

Western redcedar timber, 26 by 26cm in cross section and by 200cm long, was dried in a laboratory radio-frequency/vacuum kiln under 65torr of ambient pressure and a fixed frequency of 6.78MHz for the potential rapidly dry large timber. All process data were collected and saved in a computer through a data acquisition system. The temperature in the middle of timber was higher than temperature at the quarter point of timber length and thickness. Temperature gradients developed in the longitudinal and transverse direction of timber. The pressure in the middle of timber was higher than pressure at the quarter point of timber length. The pressure in the middle of timber was lower in the early stage of drying, and higher in the latter stage of drying than pressure at the quarter point of timber thickness. Power density was very highest during heating period and then gradually decreased. The drying curve was approximately linear and the total drying time was 27 hours from an initial moisture content(MC) of 48.6 percent to a final Me of 19.2 percent with only a few mild internal checks in the middle location of timber.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.33-46
• /
• 2006

This study was carried out to investigate a radio-frequency/vacuum (RF/V) drying ability and physical properties of the green boards and the pre-kiln dried boards with 40 mm thickness, and the 70 mm-thick green board of Iroko (Milicia excelsa). The major results were summarized as follows; The drying time from initial moisture content (MC) of 110% to approximate 6% MC for a 40mm-thick green board was 192 hours, and about 200 hours for the 70 mm-thick green board, respectively and so the RF/V drying times were dramatically shortened compared to conventional kiln drying time. The case hardenings at the RF/V drying completion stage test were very negligible, thus represented almost no existence of the residual stress. The checks were very slightly formed on all of the boards during the RF/V drying test, but crook appeared quite severely. During the accelerating test, the water-resistant treated specimens had not experienced any signs of checking occurred, whereas the control boards had encountered very frequent occurrences of end checking and slight surface checking. There were no observations of warping and discoloring regardless of the treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.1-8
• /
• 2001

Red pine (Pinus densiflora), white pine (Pinus koraiensis), larch (Larix leptolepis) and Western hemlock (Tsuga heterophylla) lumber were vacuum-press dried under three drying schedules to investigate current moisture contents (MC), drying rates and drying time factors related to five lumber thicknesses of 3, 5, 7, 9 and 11cm. Current MC could be estimated by drying factors such as lumber thickness, initial Me and drying time. Average drying rate from 30% to 15% Me was the highest for Western hemlock below fiber satuartion point, red pine, white pine and larch in the order of their magnitude. Drying rate curvilinearly decreased as lumber thickness increased. Drying time factor curvilinearly increased as lumber thickness increased.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.6
• /
• pp.981-992
• /
• 2004

Freeze drying under vacuum condition is a complex process that involves simultaneous heat and mass transfer, sublimation of ice, and motion of sublimation front. Proper treatment of the motion of sublimation interface is crucial for an accurate prediction of the freeze drying process. Based on the enthalpy formulation that has been successfully used in liquid/solid phase change problems. a fixed grid method. streamlined for the freeze drying analysis. was developed in this study. The accuracy of the fixed grid method was checked by solving a one-dimensional tray freeze drying and a two-dimensional vial freeze drying problem and then comparing the results with those by the moving grid method. Finally. the freeze drying characteristics of two-dimensional slab and axis-symmetric cylinder was investigated using the fixed grid method.

• Food Science of Animal Resources
• /
• v.42 no.5
• /
• pp.861-873
• /
• 2022

The drying of duck blood provides safety and commercial benefits, but each drying method has its own characteristics. Moreover, information on the effects of diverse drying methods on the quality of duck blood is limited. This study aimed to investigate the effects of various drying methods on the chemical and functional properties of duck blood. The physicochemical characteristics and functional properties of duck blood subjected to spray drying (SD), freeze drying (FD), vacuum drying (VD), and hot air drying (HD) were examined. The carbonyl content of FD duck blood powder was the lowest and the thermal stability was higher than that of the other treatments (p<0.05). The gel obtained from spray-dried blood displayed the lowest malondialdehyde content. The hardness, gumminess, and chewiness were the highest in the heat-induced gel prepared from FD duck blood powder (p<0.05). The gel obtained from FD duck blood displayed a denser structure than the other gel samples. Taken together, the FD duck blood exhibited excellent chemical properties and processing suitability.

• Food Science and Preservation
• /
• v.24 no.3
• /
• pp.361-366
• /
• 2017

This study investigated quality change of ginseng depending on far-infrared (FIR) drying methods. The ginseng was cut into 2 mm slices and measured moisture content (MC), color, total polyphenol content (TPC), total flavonoid content (TFC) and DPPH radical scavenging activity (DPPH). The color values (L, a, and b) were decreased after far-infrared (FIR) drying. As increase in drying time, color was changed. Considering quality parameters including MC, TPC, TFC, and DPPH, the optimum condition for drying was set at $65^{\circ}C$ for 60 min. Furthermore, we compared color and functional compounds depending on drying process including FIR, freeze-, vacuum, and hot-air drying. The color values of ginseng were decreased when dried using vacuum and hot-air. While the color values of ginseng were increased after freeze drying. Comparison with another drying method, FIR drying presented the highest color difference. FIR and vacuum-dried ginseng indicate higher contents of TPC and TFC than freeze- and hot air-dried ginseng. And hot-air-dried ginseng present the highest DPPH when compared to another drying methods. On the other hand, freeze dried ginseng show the lowest TPC, TFC, and DPPH.

• Applied Biological Chemistry
• /
• v.30 no.1
• /
• pp.65-70
• /
• 1987

In Girder to measure the pressure and weight decrease of drying sample during the vacuum drying process of food, sensing devices were designed and constructed with strain gauge. Microcomputer based vacuum drying system was made up of these devices interfaced to apple II microcomputer. The electrical output signal from vacuum sensor which constituted with Bourdon tube whereon strain gauge attached were digitalized and input to microcomputer through the MC 6821 interface I.C. chip. The relationship between read-out digital value (D) from microcomputer and readings of vacuum gauge (P, mmHg) was P=-146.136+3.620D'(r=0.9994) The pressure control of vacuum dryer was successfully conducted in the range of $400{\sim}600\;mmHg$ accuracy. The digitalized load cell output (D) could be correlated with the real weight (W, g) as W=-14,000+0.585D (r=0.9998) Drying curves of green red pepper under $64^{\circ}C$, $400{\sim}600\;mmHg$ was similar to those of red pepper and differently affected by the degree of vacuum pressure but was varied according to their shape (cut or whole). Moisture movement of green red pepper during the vacuum drying process was fitted to Page model. The empirical equations obtained were $M-M_e/M_o-M_e={\exp}\;(-0.0673{\theta}^{1.177})$ and $M-M_e/M_o-M_e={\exp}\;(-0.0655\;{\theta}^{1.477})$ for whole and cut green red pepper, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.4
• /
• pp.25-32
• /
• 2001

A microwave vacuum (MW/V) dryer was developed for drying short roundwoods, from which woodcraft souvenirs in Korean market are mostly made, and which were hardly dried without defects in a conventional kiln. It consisted of three 1.5 kW magnetrons of 2,450 MHz, a vacuum pump, a load cell of 100 kg and a cavity of $580{\times}580{\times}1,360\;mm^3$. A computer program was developed to switch on or off the magnetrons according to drying schedules, those were based on microwave injection time or the average of wood temperatures. To evaluate the new MW/V dryer the roundwood specimens of rigida pine, poplar and birch were dried. Their log diameters and lengths ranged from 125 to 25 em and from 25 to 50 cm, respectively. In spite of the presence of minor drying defects, the MW/V drying is found to be an effective method for drying short roundwoods. Wooden turneries made of red alder and ash logs were also MW/V dried from green to 4%MC without any degradation. The rates of the MW/V drying were examined for three different lengths of poplar logs.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.2
• /
• pp.288-301
• /
• 2002

A vacuum freeze drying experiment of skim milk solution in a cylindrical container is conducted to investigate the multi-dimensional drying characteristics of the process during the primary drying stage. Temperature histories at several positions are measured under the same process condition that is carefully controlled. Then the measured temperature histories at different positions are combined to produce instantaneous temperature distribution fields inside the cylindrical container. Along with the temperature measurement, the mass reduction history of the skim milk solution is also measured. From the measured temperature distribution curved configurations of sublimation interfaces and 2-dimensional heat transfer is inferred. The freeze drying under the present experimental setup is simulated with a calculation program that is based on a finite volume method with a moving grid system. Good agreements between the numerical and experimental results are observed. The present experimental results and the numerical approaches can be useful information in developing the analysis tools for practical vacuum freeze drying processes.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.9
• /
• pp.441-446
• /
• 2014

In Jeju province, the Citrus is widely spread crop which is the most popular fruit on the island. When the quality of a Citrus is not in a good condition or when its size exceeds or is lower than the set criteria, it is discarded as a waste. In this study, a drying machine for waste Citrus has been developed with 2.6 GHz microwave energy supply to the Citrus at vacuum environment. The vacuum environment of the drying chamber was maintained to reduce the energy supply to the Citrus by lowering the evaporating temperature of the water. The experiment was conducted with variation of the vacuum pressure, interior temperature of the drying chamber, and operating time of the microwave. As a result, the effect of the temperature was shown to be higher than the other two control methods, and it showed with 0.305 g/W evaporation efficiency.