• 오토저널
• /
• 제12권3호
• /
• pp.41-52
• /
• 1990

In this study are determined the unsteady temperature and thermal stress fields for a domestic 4-cylinder, 4-cycle gasoline engine cylinder head by the three-dimensional finite element method. A representative part of the cylinder head is modelled as a combination of hexahedron isoparametric elements, and the time-dependent temperature and the heat transfer coefficient of the gas are imposed as the thermal boundary conditions for the engine speeds of 500 rpm and 2000 rpm. The obtained results, which are represented graphically, indicate that the amplitudes of temperature fluctuation during a cycle are about 10.deg. C and 3.deg. C respectively on the surface of combustion chamber, and the maximum temperature fields occur at 30.deg. , 10.deg. respectively before the initiation of the exhaust stroke. Thermal stress fields due to non-uniform temperature distributions show that compressive stress is much larger than tensile stress throughout a cycle. It is also found that the compressive stress varies with substantial amplitude between the exhaust port and ignition plug hole, and the high tensile stress with small fluctuation occurs between exhaust port and the adjacent head bolt hole.

• 한국항공우주학회지
• /
• 제32권8호
• /
• pp.91-100
• /
• 2004

경사기능재료 판에 대한 열탄성 변형과 응력 해석을 위해 Green 함수 방법이 채택되었다. 3 차원 비정상 온도분포에 대한 해는 적층판 이론에 의해 얻어진다. 열탄성 문제에 대한 기본 방정식은 각각 평면외 (out-plane) 변형과 평면내 (in-plane) 힘에 의해 유도되었다. 굽힘과 평면내 힘에 의한 열탄성 변형과 응력분포는 Galerkin 방법에 근거한 Green 함수를 이용하여 해석하였다. 열탄성 변형과 응력분포 해석을 위한 Galerkin Green 함수의 특성함수들은 사각판의 제차 경계조건을 만족시키는 허용함수들의 급수 형태로 근사화되었다. 단수지시된 사각 판에 대한 수치해석이 수행되었으며, 정사기능재료의 물성치가 판의 비정상 열탄성 거동에 미치는 영향이 검토되었다.

• 한국주조공학회지
• /
• 제13권1호
• /
• pp.81-93
• /
• 1993

It is well-known that the analysis of elasto-plastic thermal stress and deformation are substantially important in optimal design of metal casting mould. The unsteady state thermal stress and deformation generated during the solidification process of ingot and mould have been analyzed by two dimensional thermal elasto-plastic theories. Distributions of temperature, stress and relative displacement of the mould are calculated by the finite element method and compared with experimental results. In the elasto-plastic thermal stress analysis, compressive stress occurred at the inside wall of the mould whereas tensile stress occurred at outside wall. A coincidence between the analytical and experimental results is found to be fairly good, showing that the proposed analytical method is reliable.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.144-154
• /
• 1998

A functionally graded material is a nonhomogeneous material, which is composed of several different materials to maintain structural rigidity and endure high temperature loads. An analytical method is presenter to solve the unsteady heat conduction equation for nonhomogeneous materials. A one-dimensional infinite plate made of functionally graded material is considered. The approximate Green's function solution is derived and to be used to obtain the temperature distribution them the stress distributions may be obtained. The volume fraction, the porosity, the stress difference, and the stress ratio are the design parameters and are to be used to set up a systematic design procedure.

• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.166-175
• /
• 2002

Tank track rubbers, which undergo dynamic stresses and strains under various road conditions, leads to a result of considerable internal temperature rise due to the heat generation. Since rubber materials are not fully elastic, a part of the mechanical energy is converted into heat because of the hysteresis loss. Heat generation without adequate heat dissipation leads to heat build-up, i.e. internal temperature rise which, if excessive, exerts a bad influence upon the performance and the life of the tank track rubbers. The purpose of this paper is to predict temperature distributions of the rubber components off tank track subjected to complex dynamic loads under various read conditions. In steady state analysis temperature fields are displayed in contour shapes, and in unsteady analysis the temperature variations of some important nodes are represented graphically with respect to the running time of the tank.