• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.905-909
• /
• 2003

This paper describes a shower type ultrasonic cleaning system using particle acceleration, developed for better effectiveness in washing out agricultural chemicals from fruits or vegetables, compared to the existing bath type ultrasonic cleaning system. The shower type system consists of a signal generator, a transducer, and a spouting nozzle, mainly. The system has been tested based on the method recommended by Korea Food and Drug Administration. It is found that shower type system shows better performance and cost-effectiveness than the bath type system that is commercially available .

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.2
• /
• pp.92-98
• /
• 2015

The physical effect induced by acoustic cavitation was investigated to accumulate basic data for the design of ultrasonic soil washing processes using aluminum foil erosion tests. A square aluminum foil was placed on the glass beads in the pyrex vessel submerged in the sonoreactor equipped with a 36 kHz ultrasound transducer module at the bottom. Cavitational erosion of foils was quantitatively analyzed for various glass bead diameter conditions (1, 2, and 4 mm), glass bead height conditions (5, 10, 15, and 20 mm), and water height conditions (5, 10, 15, and 20 mm). It was found that aluminum foil erosion significantly increased as the glass bead diameter increased and water height over the glass bead increased due to less attenuation of ultrasound and the optimization of sound field for cavitation. Moreover mechanical mixing was suggested to move constantly particles to the bottom area where the acoustic cavitation occurs most violently. It was because aluminium foil erosion by ultrasound transmitted through glass beads was relatively too weak.

• Clean Technology
• /
• v.18 no.4
• /
• pp.390-397
• /
• 2012

Removal characteristics of lead-contaminated soil at the military shooting range located in the Changwon city were studied experimentally using soil washing process. As a washing solution, hydrogen chloride (HCl) concentrations of 0.001, 0.01, 0.1 and 0.2 N were used, and soil : solution ratios were 1 : 2, 1 : 3, 1 : 4, and 1 : 5. Particle diameter of contaminated soil of 4-0.075 mm, and washing period of 5, 10, 15, 20, 30, 60, and 120 min were used as operating parameters. The optimum concentration of HCl solution was 0.1 N (56.3% of Pb removal efficiency) with 15 minutes operation period in views of economics, and the optimum soil : solution ratio was determined as 1 g : 3 mL for 69.7% of Pb removal efficiency with 0.1 N HCl and 15 minutes washing period. As washing period increased, removal efficiency was increased until 20 min of the removal efficiency of 75.3%, and then almost stable. Pb removal efficiency in soil particle diameters of 0.075 mm or more was ranged from 77.0% to 82.0%, but it was decreased to 52.8% in diameter of less than 0.075 mm. Therefore, the optimum cut-off size of the soil particle diameter was found less than 0.075 mm. Combined HCl solution and ultrasonic washing method showed better removal efficiency compared to only water or HCl washing method for particle sizes above 0.075 mm.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2642-2646
• /
• 2012

Pretreatment of spent FCC catalyst and its application in remove trace olefins in aromatics were investigated in this research. The most effective pretreatment route of spent FCC catalyst was calcining at $700^{\circ}C$ for 1 h, washing with 5% oxalic acid solution in ultrasonic reactor and dried. Treated spent FCC catalyst was modified with metal halides, then to prepare catalyst to remove trace olefins in aromatics. X-ray diffraction, Pyridine-FTIR, $N_2$ adsorption-desorption and inductively coupled plasma optical emission spectrometer (ICP-OES) were used to investigate the pretreatment process. The result showed that the performance of the treated spent FCC catalyst was much greater than that of the spent FCC catalyst, which indicted the possibility and improvement of this research.

• Journal of the Korean Professional Engineers Association
• /
• v.41 no.3
• /
• pp.24-29
• /
• 2008

Recently, the serious problems have been occurred due to the contaminated sites with heavy metals are increasing. There are several remediation technologies of the metal contaminated soil such as physical separation, washing with water or acid, biologically, electrically. Pytoremediation, ultrasonic etc. Among these technologies the physical separation can be put in a good option to solve the metal contaminated soil economically and environmental friendly. Because this technology has been already commercially certificated in the mineral processing field for a long time.

• Journal of Korean Ophthalmic Optics Society
• /
• v.16 no.1
• /
• pp.31-40
• /
• 2011

Purpose: This study was performed to investigate the actual state about ultrasonic cleaning of soft contact lenses in local optical shops and evaluate the removal effect of protein deposit on soft contact lenses with different lens containers by ultrasonic cleaner for eyeglasses. Methods: The actual state about ultrasonic cleaning of soft contact lenses was surveyed in total 75 local optical shops in Seoul, Korea. The cleaning efficacy of different lens containers was compared by measuring the protein remained on ocufilcon D contact lenses after washing by an ultrasonic cleaner for eyeglasses. The changes on surfaces and wetting angles of ocufilcon D contact lenses by repeat ultrasonication were further investigated. Results: The main purpose to use ultrasonic cleaners in local optical shops was rapid cleaning. The ultrasonic cleaning efficacy of ocufilcon D contact lenses with glass containers was little higher than it with plastic containers, but was not significantly different. The changes on surfaces and wetting angles of ocufilcon D contact lenses in a plastic lens container by repeat ultrasonication such as 30 and/or 60 times were shown. Conclusions: There was not significant difference in cleaning efficacy between glass and plastic lens containers. However, repeat cleaning with ultrasonic cleaner for eyeglasses would be carefully considered since some significant changes in the parameters of lens surface and wetting angles were detected by repeat ultrasonification even when lens containers were used for ocufilcon D contact lens during ultrasonictions.

• Clean Technology
• /
• v.16 no.4
• /
• pp.265-271
• /
• 2010

The deactivated diesel oxidation catalyst(DOC) was remanufactured by ultrasonic wave treatment with various solutions, followed by active component re-impregnation. The catalytic performance and surface properties of remanufactured DOC were studied at various remanufacturing conditions. The proper ultrasonic-wave cleaning time at various solutions and optimal re-impregnation amounts of active component for the best catalytic performance were investigated. The catalytic performance tests on the conversions of CO and THC(total hydrocarbon) were also carried out at various temperatures by catalytic reaction test unit using bypass gas from the diesel engine dynamo system. It was found that the catalytic performance of DOC remanufactured with the high-temperature air washing, ultrasonic wave cleaning at acidic/basic solutions and active component re-impregnation method was recovered to 90% level of its activity compared to that of the fresh DOC, which was caused by removing the deactivating materials from the surface of the DOC through the analyses of catalyst performance test and their characterization by Optical microscope, EDX, ICP, TGA, and porosimeter.

• Applied Biological Chemistry
• /
• v.48 no.4
• /
• pp.388-393
• /
• 2005

This study was conducted to experiment the removal efficiency of 6 pesticides in fruits and vegetables using various washing solutions. As results, the average removal efficiencies of pesticides washed with tap-water were 68.3%, whereas those washed by ultrasonic cleaning for 2 and 5 minutes were 73.7% and 82.5%, respectively. Using different washing solutions with various additional materials such as 0.5% detergent, 5% vinegar, 5% salt and flour, the removal rates were 82.9%, 76.9%, 75.8% and 75.7%, respectively. With 0.5% detergent, pesticides were 20% more removed when washed by ultrasonic cleaning than tap-water washing; moreover, Chlorthalonil in cherry tomato showed the highest removal efficiency while EPN in grape washed with tap-water showed the lowest. The order of removal efficiencies of pesticides were Chlorthalonil (90.0%)>Procymidone (81.3%)>Chlorpyrifos (76.6 %)>Endosulfan (75.7%)>Fenitrothion (75.5%)>EPN (73.8%).

• Korean Journal of Food Science and Technology
• /
• v.32 no.4
• /
• pp.763-771
• /
• 2000

The 88 kinds of pesticide residues were analyzed in 12 kinds(289 samples) of fruits and vegetables brought at department store & mart in Kwangju from Feburary to September in 1999. The detection rate of pesticide residue in 12 kinds(289 samples) of fruits and vegetables was 21.1%, and the rate exceeds standard was 5.2%. The order of highly exceed rate in fruits and vegetables were perilla leaf, lettuce, spinach and chickery. The order of pesticide which founded frequently in fruits and vegetables were procymidone, endosulfan, vinclozoline, chlorpyrifos, cyprermethrin, pirimiphos-M, fenvalerate, fenarimol, and monocrotophos. And that of pesticide which exceed highly standard were procymidone, vinclozolin, endosulfan, pirimiphos-M, fenarimol, monocrotophos, etc. Eight different washing methods were compared for removal efficiencies of residual pesticides(procymidone, vinclozoline) on the perilla leap, the lettuce, the spinach, the strawberry, and the minitomato. Residual pesticides such as procymidone and vinclozoline were removed most efficiently by ultrasonic washing.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.4_2
• /
• pp.561-570
• /
• 2023

This study was to evaluate the effect of different rinsing times and methods on the accuracy of temporary prostheses fabricated by 3D printing method. Sixty temporary prostheses were fabricated with LCD types of 3D printer(Halot-Sky, Creality, Shenzhen, China) and divided into six groups (n = 10) based on rinsing times and methods. All specimens were rinsed with 99% isopropanol alcohol for 5 and 10 min using three methods-hand washed, ultrasonic cleaning, and automated washing. All specimens were polymerized for 3 minutes under the same conditions. The marginal and internal gaps of specimens were examined using a replica technique. The light-body silicone thickness was measured at 6 reference points(Absolute marginal discrepancy, Marginal, Chamfer, Axial, Angle, and Occlusal gap). All measurements were performed by a stereomicroscope. Reference point images were taken at 100× magnification and then measured using an image analysis program. Statistical analysis was performed using Two-way ANOVA, One-way ANOVA, and the Kruskal-Wallis test (p = .05). The marginal and internal gaps were statistically different according to the rinsing methods and rinsing times(p < .001). In the rinsing time, the temporary prosthesis rinsed for 5 minutes group showed higher accuracy than 10 minutes group. In the rinsing method, the hand washing group showed higher accuracy than the automated washing group.