• 한국염색가공학회지
• /
• 제34권3호
• /
• pp.135-145
• /
• 2022

In this study, the dyeability of 0.06-denier-per-filament (dpf) ultrafine sea-island-type nylon knitted fabric was investigated and compared with that of 1.0-dpf general nylon with respect to four types of dyes. In particular, leveling, milling, half-milling, and metal-complex dyes were compared at concentrations of 0.5%, 1.0%, 2.0%, 4.0%, and 8.0% on-weight-fabric (o.w.f). In each case, staining was performed at 100 ℃. The dyeabilities of the materials were compared in terms of the depth of color as defined by the ratio of the absorption coefficient (K) to the scattering coefficient (S). Results indicated generally low K/S values for both the 0.06-dpf ultrafine sea-island-type nylon and 1.0-dpf general nylon. In terms of the dye type, the milling and half-milling dyes exhibited K/S values of ≥20 for all colors of yellow, red, and blue for the 0.06-dpf ultrafine yarn sea-island-type nylon, which were superior to those of the other dye types. Hence, the milling and half-milling dyes are considered more suitable than the other dyes. Further, a comparison of dye fastness and compatibility revealed that the half-milling dye was the most suitable dye for the 0.06-dpf ultrafine sea-island-type nylon.

• 한국분말재료학회지
• /
• 제6권2호
• /
• pp.139-144
• /
• 1999

The pure Ti, Ni and carbon powders were reaction milled to synthesize the TiC-Ni based cermet powders with ultrafine microstructures. After milling, the ultrafine TiC or amorphous Ti-Ni phase was obtained, respectively, according to the milling condition. The effects of milling variables on the synthesizing behavior of the powders were investigated in detail. The sintered TiC-Ni based cermet of the reaction milled powders consisted of very fine TiC of 0.2~1.5$\mu$m, as compared with that of a commercial cermet of 3~5$\mu$m. This demonstrates the potenial of reaction milling as an effective processing route for the preparation of cermet materials.

• 한국염색가공학회지
• /
• 제22권4호
• /
• pp.325-331
• /
• 2010

The alkaline dissolution behavior of sea-island type ultrafine nylon fiber were dependent on the concentration of NaOH and treatment time, and the most appropriate condition for alkaline dissolution was to treat with 20g/l NaOH for 30 min at $80^{\circ}C$. The dyeing properties of sea-island type ultrafine nylon fiber and regular nylon fiber were examined with 3 different types of acid dyes in this study. The dye uptakes of ultrafine nylon fiber were higher than regular nylon fiber because of large surface area per unit mass, which increased as the dye bath pH decreased. The dyeing rates on ultrafine nylon fiber were faster and dye exhaustions were higher than regular nylon fiber, however color strength and rating of wash fastness were lower. It was also found that levelling type acid dye showed fast dyeing rate on both nylon fibers than metal-complex and milling type acid dyes.

• Food Science and Biotechnology
• /
• 제17권4호
• /
• pp.833-838
• /
• 2008

Size effects of rice product powders on physical properties including suspension stability were investigated in this study. Endosperm, bran, and husk powders of rice with different size particles were prepared using the pin crusher or the ultrafine air mill. The physical properties of the powders were examined using particle size analysis, scanning electron microscopy, and spectrophotometry. The peak of the volume-weighted particle distribution of ultrafine endosperm particles was at $5.4\;{\mu}m$ whereas those of the bran and the husk appeared at 65 and $35\;{\mu}m$, respectively. Ultrafine particles of the endosperm and the husks dispersed better than larger-sized particles. As time elapsed, the dispersibility decreased, but the ultrafine particles were precipitated at the slowest rate. Our results suggest that ultrafine particles, including future nanosized particles, provide improved solubility and dispersibility resulting in better stability in the food colloidal suspension.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.829-830
• /
• 2006

Recent research at Harbin Institute of Technology on the synthesis of nanocrystalline and untrafine grained materials by mechanical alloying/milling is reviewed. Examples of the materials include aluminum alloy, copper alloy, magnesium-based hydrogen storage material, and $Nd_2Fe_{14}B/{\alpha}-Fe$ magnetic nanocomposite. Details of the processes of mechanical alloying and consolidation of the mechanically alloyed nanocrystalline powder materials are presented. The microstructure characteristics and properties of the synthesized materials are addressed.

• 한국분말재료학회지
• /
• 제19권1호
• /
• pp.25-31
• /
• 2012

In this study, a high energy ball milling process was employed in order to improve the densification of direct nitrided AlN powder. The densification behavior and the sintered microstructure of the milled AlN powder were investigated. Mixture of AlN powder doped with 5 wt.% $Y_2O_3$ as a sintering additive was pulverized and dispersed up to 50 min in a bead mill with very small $ZrO_2$ beads. Ultrafine AlN powder with a particle size of 600 nm and a specific surface area of 9.54 $m^2/g$ was prepared after milling for 50 min. The milled powders were pressureless-sintered at $1700^{\circ}C-1800^{\circ}C$ for 4 h under $N_2$ atmosphere. This powder showed excellent sinterability leading to full densification after sintering at $1700^{\circ}C$ for 4 h. However, the sintered microstructure revealed that the fraction of yitttium aluminate increased with milling time and sintering temperature and the newly-secondary phase of ZrN was observed due to the reaction of AlN with the $ZrO_2$ impurity.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.305-307
• /
• 1997

Gd-doped $CeO_2$, ultrafine powders were synthesized by the glycine-nitrate process and then their sintering and electrical characteristics were analysed using the dilatometric and AC impedance measurements. In the dilatometric measurements green bodies from the synthesized powders after milling shrinked to about $1470^{\circ}C$ in appearance and then expanded thermally with the increase of the heating temperature, whereas those from the synthesized powders before milling continuously shrinked to the temperatures of $1600^{\circ}C$. It may be due to the change of the packing density of the synthesized powders by milling. In the AC impedance measurements, the electrical resistivity of the Gd-doped $CeO_2$ bodies from the as-milled powders, sintered at $1500^{\circ}C$ with the increase of the sintering time, showed the minimum value at the sintering time of 10h. The minimum total resistivity of the Gd-doped $CeO_2$ bodies sintered at $1500^{\circ}C$ for 10h seems to result from the lowest activation energy by the combination between the activation energies for the resistivities at the grain interior and grain boundary.

• 한국분말재료학회지
• /
• 제24권5호
• /
• pp.406-413
• /
• 2017

A Nanosized $WO_3$ and CuO powder mixture is prepared using novel high-energy ball milling in a bead mill to obtain a W-Cu nanocomposite powder, and the effect of milling time on the structural characteristics of $WO_3-CuO$ powder mixtures is investigated. The results show that the ball-milled $WO_3-CuO$ powder mixture reaches at steady state after 10 h milling, characterized by the uniform and narrow particle size distribution with primary crystalline sizes below 50 nm, a specific surface area of $37m^2/g$, and powder mean particle size ($D_{50}$) of $0.57{\mu}m$. The $WO_3-CuO$ powder mixtures milled for 10 h are heat-treated at different temperatures in $H_2$ atmosphere to produce W-Cu powder. The XRD results shows that both the $WO_3$ and CuO phases can be reduced to W and Cu phases at temperatures over $700^{\circ}C$. The reduced W-Cu nanocomposite powder exhibits excellent sinterability, and the ultrafine W-Cu composite can be obtained by the Cu liquid phase sintering process.

• Nuclear Engineering and Technology
• /
• 제53권8호
• /
• pp.2582-2590
• /
• 2021

The high-energy milling is one of the most extended techniques to produce Oxide dispersion strengthened (ODS) powder steels for nuclear applications. The consequences of the high energy mill process on the final powders can be measured by means of deformation level, size, morphology and alloying degree. In this work, an ODS ferritic steel, Fe-14Cr-5Al-3W-0.4Ti-0.25Y₂O₃-0.6Zr, was fabricated using two different mechanical alloying (MA) conditions (M_std and M_act) and subsequently consolidated by Spark Plasma Sintering (SPS). Milling conditions were set to evidence the effectivity of milling by changing the revolutions per minute (rpm) and dwell milling time. Differences on the particle size distribution as well as on the stored plastic deformation were observed, determining the consolidation ability of the material and the achieved microstructure. Since recrystallization depends on the plastic deformation degree, the composition of each particle and the promoted oxide dispersion, a dual grain size distribution was attained after SPS consolidation. M_act showed the highest areas of ultrafine regions when the material is consolidated at 1100 ℃. Microhardness and small punch tests were used to evaluate the material under room temperature and up to 500 ℃. The produced materials have attained remarkable mechanical properties under high temperature conditions.

• Carbon letters
• /
• 제19권
• /
• pp.23-31
• /
• 2016

Carbon rich fly ash was recently reported to have compositions that are ideal for use as a precursor and catalyst for carbon nanotube growth. This fly ash powder is mostly composed of pure carbon, predominantly present as sp². In this work, the effect of sonication time on the morphology and structural properties of carbon rich fly ash particles is reported. The obtained results show that ultrasound treatment is an effective tool for producing ultrafine particles/fragments with higher porosity, which might be suitable for the adsorption of gasses. Moreover, carbon nanoparticles (CNPs) of this fly ash were produced in parallel using the ball milling technique, and were evaluated as reinforcements for epoxy based composites. These CNPs have almost spherical shapes with particle sizes of around 30 nm. They were found to have strong C=O carbonyl group bonds, which might be generated during the ball milling process. The tensile testing results of a fly ash CNP reinforced epoxy composite showed significant improvements in the mechanical properties, mainly in the stiffness of the polymer. The stiffness value was increased by around 23% of that of neat epoxy. These CNPs with chemically active groups might also be useful for other applications.