• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.677-686
• /
• 2005

The allowable bearing capacity of a pile, the most important factor in stability estimation, is determined by applying safety factor to the ultimate load or yield load. There are several but contradictory methods available in current design codes to estimate the allowable bearing capacity and the safety factor. This paper analyzes load-settlement curves obtained from 19 static load tests measured from 11 sites. At all tests, the load is applied until apparent failure is observed. The validity of the ultimate and yield load estimation method and load caculated from the settlement criterion is investigated through comparison with the measured data. In addition, a new procedure to estimate allowable load and safety factor is proposed. Additional data from field static load tests, such as those incorporated in this study, are needed to more reliably apply the proposed method in design practice.

• Steel and Composite Structures
• /
• v.9 no.6
• /
• pp.569-584
• /
• 2009

Corrosion of steel rebars in bridge decks which are faced to harsh conditions, is a common problem in construction industries due to the porosity of concrete. In this research, the behavior of one-way concrete slabs reinforced with Glass fiber reinforced polymer (GFRP) molded grating is investigated both theoretically and experimentally. In the analytical method, a closed-form solution for load-deflection behavior of a slab under four-point bending condition is developed by considering a concrete slab as an orthotropic plate and defining stiffness coefficients in principal directions. The available formulation for concrete reinforced with steel is expanded for concrete reinforced with GFRP molded grating to predict ultimate failure load. In finite element modeling, an exact nonlinear behavior of concrete along with a 3-D failure criterion for cracking and crushing are considered in order to estimate the ultimate failure load and the initial cracking load. Eight concrete slabs reinforced with steel and GFRP grating in various thicknesses are also tested to verify the results. The obtained results from the models and experiments are relatively satisfactory.

• Geomechanics and Engineering
• /
• v.15 no.4
• /
• pp.973-986
• /
• 2018

The objective of this paper is to present abacuses obtained from a parametric study of deep-lined tunnels using a numerical finite element model. This numerical model was implemented in software GEOMEC91, which is a two-dimensional axisymmetric model that considers the progress of excavation and the placing of the lining through the activation and deactivation of elements. It is adopted a step of excavation constant (1/3 of radius), constant velocity and circular cross section along the tunnel axis. It is used for rock mass a viscoplastic constitutive law with von-Mises criterion of viscoplasticity without hardening whose deformation rate over time is given by the Bingham model. The lining uses a linear elastic constitutive law. In total are 1716 analysis presented in 60 abacuses that show the value of ultimate convergence ($U_{eq}$) due to tunneling speed. In addition, it is shown an example of the use of the abacuses to determine the ultimate convergence ($U_{eq}$) of the tunnel and pressure ($P_{eq}$) on the lining.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.28 no.5
• /
• pp.93-103
• /
• 2000

This research is to propose a rational criterion of the selection and the management f the roadside trees, and to establish the planting design and system with the objective of improving the roadside environment. All of the roadside trees in each objective courses in Kangnung, and the soil disposition, hardness of the soil in the planting areas have been investigated. Also, we have surveyed the kinds of the trees which kandgnung inhabitants want. The conclusion is as follows Most of roadsides have trees, but they need the introduction of shrubs or ground covering plants according to the locations and the environmental conditions. We have selected nineteen species in regard to the roadside tree criterion and the growing conditions living in Kangnung. It is desirable that we make banding style planting space between each roadside tree to improve the low ratio of green coverage. We have found out that Ligustrum obtusifolium, Buxus micropnylla, Euonymus japonica, Rhododendron schlippenbachii, Phyllostachys nigro and Rosa rugosa, ect. are suitable. In order to soften and weaken the rigidity of the hard substances on a paved roadside, the climbers such as the perennial herbaceous flowering and hedera rhombea should be preferred rather than annual herbaceous flowering because of curtailment of expenditure. To posses a systematical greenery frame in kangnung, we have planned a planting design system that would expand the greenery space every year. Moreover, we have to make a plan to overcome space restrictions. We have established a flexible plan considering the roadside conditions and the improved standard planting methods with an ultimate aim to create a special roadside view.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.4
• /
• pp.383-398
• /
• 2012

A finite element analysis study was performed to investigate the behavior and strength of a Plate-Circular Hollow Section joint stiffened with Rib-plate, Since The strength of plate-Circular Section joint is reduced by joint of stress and local plastic deformation which is caused by wall moment, rib plates are attached to the upper and lower Plate-Circular Hollow Section joint for redistribution of stress. The behaviors of joints stiffened with Rib-plate according to shape of rib and reinforcing method, etc are different from those of joints which is not stiffened. However, the criterion of hollow structural section was limited on some parts. Therefore, this study intends to investigate the behavior and structural capacity of Plate-Circular Hollow Section joints stiffened with Rib-plate and compare the Finite element analysis with the Design Equation. Finally, this study proposes the reasonable ultimate strength formula through the comparisons with other design guide.

• Earthquakes and Structures
• /
• v.24 no.1
• /
• pp.11-20
• /
• 2023

"Performance-based design (PBD)" is based on designing a structure with choosing a performance target under design criteria to increase the structure's resistance against earthquake effect. The plastic hinge formation is determined as one of the fundamental data in finite elements nonlinear analysis to distinguish the condition of the structure where more significant potential damage could occur. If the number of plastic hinges in the structure is increased, the total horizontal load capability of the structure is increased, also. Theoretically, when the number of plastic hinges of the plane frame structure reaches "the degree of hyperstaticity plus one", the structure will reach the capability of the largest ultimate horizontal load. As the number of plastic hinges to be formed in the structure increases towards the theoretical plastic hinge number (TPHN), the total horizontal load capability of the structure increases, proportionally. In the previous studies of the authors, the features of examining the new performance criteria were revealed and it was formulated as follows "Increase the total number of plastic hinges to be formed in the structure to the number of theoretical plastic hinges as much as possible and keep the structure below its targeted performance with related codes". With this new performance criterion, it has been shown that the total lateral load capability of the building is higher than the total lateral load capability obtained with the traditional PBD method by the FEMA 440 and FEMA 356 design guides. In this study, PBD analysis results of structures with frame carrier systems are presented in the light of the Turkey Building Earthquake Code 2019. As a result of this study, it has been shown that the load capability of the structure in the examples of structures with frame carrier system increases by using this new performance criterion presented, compared to the results of the examination with the traditional PBD method in TBEC 2019.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.81-86
• /
• 2001

The concrete bridge decks are in need of replacement and rehabilitation due to decreasing load carrying capacity. In this study, to propose a strengthening technique that improves usability and structural performance of the bridge deck and to propose an efficient strengthening design technique which satisfies both the strength End serviceability of the bridge deck, this paper shows the failure characteristics of the strengthened bridge decks and proposes an empirical yield criterion. Therefore, strengthening efficiency was proposed based on the experiment and yield line analysis result. The yield line theory which adopts the modified criteria of Johansen is considered to predict the ultimate strength about all strengthening material(Carbon Fiber Sheet, Carbon Fiber Rod, Grid Type Carbon Fiber).

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.3
• /
• pp.294-299
• /
• 2006

This paper studies a visual feedback control scheme for robot manipulators with camera-in-hand configurations. We design a robust controller that compensates for bounded parametric uncertainties of robot mechanical dynamics. In order to reduce steady state tracking error of the robot arms due to uncertain dynamics, integral action is included in the control input. Using the Lyapunov stability criterion, the uniform ultimate boundedness of the tracking error is proved. Simulation and experimental results with a 2-1ink robot manipulator illustrate the robustness and effectiveness of the proposed control algorithm.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.285-290
• /
• 2002

The double composite box girder is a structural system filled with concrete at the bottom of the steel box in the negative moment region increasing the flexural strengths. Flexural strengths of the double composite steel box girders are investigated through a series of the experimental tests and the numerical analysis. The experimental tests are performed on the three kinds of steel box girders with the different concrete depths including loom, 15cm, and 20cm. Moment-curvature relations are calculated based on the sectional analysis method describing the nonlinear natures of concrete and steel. In the finite element analysis the nonlinear nature of concrete is described based on the three dimensional four-parameter constitutive model recently developed and that of steel is described based on von Mises failure criterion. The ultimate flexural capacities of the box girders predicted using sectional analysis and finite element analysis show good agreement with those of the experiments.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.4
• /
• pp.135-147
• /
• 1992

본 연구는 기존의 이론을 배경으로 전단키에 영향을 미치는 전달전달의 요소가 포함된 기본식을 산정하여, 접합부의 유형에 따라 구체적으로 전단강도를 예측하는 방법을 제안하였다. 접합부 콘크리트와 횡보강철근의 강도 및 장부호과를 고려한 프리캐스트 콘크리트 전단키 접합부의 기본극한강도식은 수정 Mohor-Coulomb의 파괴기준과 항복선의 도입에 의하여 전개하였고, 극한전단능력의 근사해는 상하계법에 의한 극치해석의 수법을 이용하여 구하고 여기에 재료의 유효강도계수를 도입하였다. 또한, 지존의 실험결과와 비교하여 그 적용성을 고찰하였다.