• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.12.1-12.1
• /
• 2009

For the micro conductive line, memory device fabrication process use many expensive processes such as manufactur-ing of photo mask, coating of photo resist, exposure, development, and etching. However, direct printing technology has the merits about simple and cost effective processes because nano-metal particles contained inks are directly injective without mask. And also, this technology has the advantage about fabrication of fine pattern line on various substrates such as FPCB, PCB, glass, polymer and so on. In this work, we have fabricated the fine and thick metal pattern line on flexible PCB substrate for the next generation electronic circuit using Ag nano-particles contained ink. To improve the line tolerance on flexible PCB, metal lines are fabricated by sequential prinitng method. Sequential printing method has vari-ous merits about fine, thick and high resolution pattern lines without bulge.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.4 s.235
• /
• pp.504-511
• /
• 2005

The generation of fine relics of inorganic and metallic materials from precursor suspensions is of significant current interest as it holds the key to the fabrication of display and printed circuit board. Some novel printing methods depositing ceramic particles have been suggested in recent years. When a conducting liquid is supplied to a capillary nozzle at a low flow rate and when the interface between air and the liquid is charged to a sufficiently high electrical potential, the liquid meniscus takes the form of a stable cone, whose apex emits a microscopic jet. This is called as a cone-jet mode. In our experiments, an alumina particles flowing through a nozzle were subjected to electro-hydrodynamic printing in the cone-jet mode. The pattern of 'YONSEI' characters was tested at $10 {\mu}l/min$ of alumina ink flow rate and different applied voltages. At an applied voltage of 6 kV, feature size was in the range of $250 {\mu}m.$

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.11
• /
• pp.3-10
• /
• 2018

Cladding that finishes the exterior of a building could enhance the value of the building, and shape control is an important factor. With the recent development of 3D printing, cementitious claddings were printed by 3D printer in China, U.S.A and elsewhere. On the other hand, the structural safety of the exterior panel should be examined, as casualties occur when the exterior panel fails due to typhoon or impact. Cement-based cladding is reinforced by wire mesh to improve safety. Introducing 3D printing composite system with polymer and cement, makes it possible to produce claddings fast and accurate. Prior to the development of 3D printing cementitious cladding, the major parameters influencing the optimal shape were identified based on structural performance. The wind load, joint, and bond behavior between polymer and cement were considered. Polymer laminate shape, order, and thickness were variables, and finite element analysis was performed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.506-508
• /
• 2005

In general, organic TFTs are comprised of four components: gate electrode, gate dielectric, organic active semiconductor layer, and source and drain contacts. The TFT current, in turn, is typically determined by channel length and width, carrier field effect mobility, gate dielectric thickness and permittivity, contact resistance, and biasing conditions. More recently, a number of techniques and processes have been introduced to the fabrication of OTFT circuits and displays that aim specifically at reduced fabrication cost. These include microcontact printing for the patterning of metals and dielectrics, the use of photochemically patterned insulating and conducting films, and inkjet printing for the selective deposition of contacts and interconnect pattern. In the fabrication of organic TFTs, microcontact printing has been used to pattern gate electrodes, gate dielectrics, and source and drain contacts with sufficient yield to allow the fabrication of transistors. We were fabricated a pentacene OTFTs on flexible PEN film. Au/Cr was used for the gate electrode, parylene-c was deposited as the gate dielectric, and Au/Cr was chosen for the source and drain contacts; were all deposited by ion-beam sputtering and patterned by microcontact printing and lift-off process. Prior to the deposition of the organic active layer, the gate dielectric surface was treated with octadecyltrichlorosilane(OTS) from the vapor phase. To complete the device, pentacene was deposited by thermal evaporation and patterned using a parylene-c layer. The device was shown that the carrier field effect mobility, the threshold voltage, the subthreshold slope, and the on/off current ratio were improved.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.4_2
• /
• pp.629-637
• /
• 2023

This study aimed to evaluate the effect of post-curing equipment and time on the flexural strength of 3D printing resins produced by a liquid crystal display(LCD) printer. The three 3D printing resins(DENTCA Denture Teeth, DT; C&B 5.0 hybrid, CH; C&B Permanent A2, CP) were divided into four groups according to post-curing time(10 min and 30 min) and equipment with or without vacuum treatment. For the three-point flexural strength test and biaxial strength test were prepared by method according to ISO 10477, ISO 6872, respectively. Flexural strength was measured with universal testing machine. Comparison between post-curing time of each post-curing equipment was analyzed by independent sample t-test and Mann-Whitney U test(α=.05), and comparison between groups according to each 3D printing resin was performed by Kruskal-Wallis test and post-hoc by Bonferroni-Dunn test(α=.05). The flexural strength of the resin post-curing under vacuum was higher than that of the resin post-curing in air. In the comparison according to the post-curing time, in the case of the post-curing equipment without vacuum, the 30 minute curing time showed significantly higher flexural strength than the 10 minute curing time, except for the biaxial flexural strength of CH(P<.05). In the post-curing equipment with vacuum, the three-point flexural strength of all 3D printing resins(DT, CH, and CP) showed a higher value at 30 minute curing time than at 10 minute curing time.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.02a
• /
• pp.264.2-264.2
• /
• 2009

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2009.10a
• /
• pp.77-77
• /
• 2009

• Information Display
• /
• v.10 no.5
• /
• pp.14-26
• /
• 2009

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.202-213
• /
• 2008

This study set up a relational model and an assumption concerning how consumer innovativeness could affect the usage motive of digital photos and the usage intention of digital photo printing service, by utilizing the theory of Uses and Gratification(U&G) and Technology Acceptance Model(TAM) so as to cope with the changes in market environment and to construct a new business model. The results fur the study were as below First, innovativeness had a positive effect on convenience, entertaining element and sociality in the relational model of overall innovativeness and usage motive of digital photos. Second, it has been noted that innovativeness had a positive effect on the usage intention of digital photo printing service in the relational model between overall innovativeness and its usage intention. Third, it has been demonstrated that convenience, entertaining element, economic feasibility and sociality had a positive effect on its usage intention in the relational model between overall usage motive of digital photos and the usage intention of digital printing service

• Journal of the Korean Graphic Arts Communication Society
• /
• v.20 no.1
• /
• pp.146-158
• /
• 2002

JPEG is good for full color representation but is poor in quality of image because of the small size and the losing compression ways. GIF is a kind of format style made for image - transmission in Compuserve which is a method of PC communication in U. S. A and now is used in world wide web owing to the efficiency of file compression and transmission. But GIF only is used 256 colors, so the images in web has a poorer quality of colors effect to be compared with those of printed catalogues. Also there can be licence problems when the images is used for commercial uses because the possession is Compuserve. The PNG is a way that the total advantages of JPEG and GIF. PNG image file is a more skillful (bitmap display unit), shows a high quality image like TIFF image about, gives superior compression , a 10% to 30% represents full color, 256 color, gray like JPEG. GIF file which uses LZW compression file is a thing which pays licence, In other hands, PNG is free from licence and more skillful image processing method against image error, and it is possible to conserve the color information. Therefore, this treatise is about how various images which are utilized for commercial printings in web, can be made into PNG files about the compression file. And the representation of image by compared the G]U images with JPEG images as well as compression file and the representation of image the superiority of color representation. In addition, 1 check out how much ranges the PNG files are available for electronic publish printing.