• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.13-22
• /
• 1991

This study investigated the effects of surface treatment on the tensile bond strength of resinbonded prosthesis. The Rexillium III specimens were treated with $50{\mu}m\;Al_2O_3$ blasting. Type IV gold alloy specimens were treated with $400^{\circ}C$ heating and tin plating method. All specimens were bonded with MBAS composite resin cement and followed by immersion test into the $37^{\circ}C$ water bath for 7 days. The specimens were debonded in tension with an Instron machine and observed with SEM. The modes of failure were recorded also. The following conclusions were obtained : 1. The tensile bond strength decreased in following order. $50{\mu}m\;Al_2O_3$ basted Resillium III group, Type IV gold alloy group treated with $400^{\circ}C$ heat and tin plating type IV gold alloy group, and statistical significant differences were observed(p<0.05). 2. The tensile bond strength decreased in all groups after 7 days immersion test, but statistical significant differences were observed in Rexillium III specimens only. 3. The sharp and irregular surface were observed in Rexillium III, but $400^{\circ}C$ heat treated and tin plated groups had round and broad surface in SEM. 4. The models of bond failure were cohesive-adhesive failure mainly.

• 식물분류학회지
• /
• 제37권4호
• /
• pp.503-527
• /
• 2007

Nakai 박사에 의해 기재된 것으로 알려진 울릉도산 55분류군에 대한 기준표본을 동경대학교 표본관(TI)에서 확인하였다. 이중 4분류군의 학명은 Nakai가 최초 명명한 것이 아니라 신조합명이었고, 15개 분류군의 기준표본은 본 연구 이전에 이미 설정된 것을 확인하였다. 본 연구에서는 지금까지 기준표본이 설정되지 않았던 36개 분류군 중 본 연구기간 중 기준표본을 검토할 수 없었던 6개 분류군과 유효공표 여부를 확인하지 못한 5개 분류군을 제외한 25개 분류군의 기준표본을 검토하였고, 일부 분류군에 대해서는 선정기준표본을 설정하였다.

• Restorative Dentistry and Endodontics
• /
• 제18권1호
• /
• pp.1-26
• /
• 1993

The purpose of this study was to investigate the effect of acid etching on the surface appearance and fracture toughness of five glass ionomer cements. Five kinds of commercially available glass ionomer cements including chemical curing filling type, chemical curing lining type, chemical curing metal reinforced type, light curing tilling type and light curing lining type were used for this study. The specimens for SEM study were fabricated by treating each glass ionomer cement with either visible light curing or self curing after being inserted into a rubber mold (diameter 4mm, depth 1mm). Some of the specimens were etched with 37% phosphoric acid for 0, 15, 30, 60, go seconds, at 5 minutes, 1 hour and 1 day after mixing of powder and liquid. Unetched ones comprised the control group and the others were the experimental groups. The surface texture was examined by using scanning electron microscope at 20 kV. (S-2300, Hitachi Co., Japan). The specimens for fracture toughness were fabricated by curing of each glass ionomer cement previously inserted into a metal mold for the single edge notch specimen according to the ASTME399. They were subjected to a three-point bend test after etching for 0, 30, 60, and 90 seconds at 5 minutes-, 1 hour-and 1 day-lapse after the fabrication of the specimens. The plane strain fracture toughness ($K_{IC}$) was determined by three-point bend test which was conducted with cross-head speed of 0.5 mm/min using Instron universal testing machine (Model No. 1122) following seven days storage of the etched specimens under $37^{\circ}C$, 100% humidity condition. Following conclusions were drawn. 1. In unetched control group, crack was present, but the surface was generally smooth. 2. Deterioration of the surface appearance such as serious dissolving of gel matrix and loss of glass particles occured as the etching time was increased beyond 15 s following Immediate etching of chemical curing type of glass ionomer cements. 3. Etching after 1 h, and 1 d reduced surface damage, 15 s, and 30s etch gave rough surface appearance without loss of glass particle of chemical curing type of glass ionomer cements. 4. Light curing type glass ionomer cement was etched by acid, but there was no difference in surface appearances according to various waiting periods. 5. It was found that the value of plane stram fracture toughness of glass ionomer cements was highest in the light curing filling type as $1.79\;MNm^{-1.5}$ followed by the light curing lining type, chemical curing metal reinforced type, chemical curing filling type and chemical curing lining type. 6. The value of plane stram fracture toughness of the chemical curing lining type glass ionomer cement etched after 5 minutes was lower than those of the cement etched after 1 hour or day or unetched (P < 0.05). 7. Light curing glass ionomer cement showed Irregular fractured surface and chemical curing cement showed smooth fractured surface.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.141-147
• /
• 2014

This study aims to investigate the influence of bevel angles on the fatigue life of V-groove butt-welded joints with back-plates made by SM490A steel material, generally used for excavators, because changes in the geometry, material and surface properties of welded regions affect the fatigue life of welded structures. Butt type test specimens were prepared by the $CO_2$ welding of rolled steel plates (SM50A steel) with a thickness of 13.5 mm at a welding speed of 30 cm/min and these Butt type test specimens had two different groove angles, which are $40^{\circ}$ (A type) and $30^{\circ}$ (B type). In order to investigate differences in fatigue life between two types, 4-point bending fatigue tests were conducted with a stress ratio of R=0.1 under the cyclic loading environment at a frequency of 5 Hz at room temperature. The fatigue life of A type specimens was approximately 7% higher than that of B type specimens. The stress concentration factors calculated by finite element analysis were 2.16 for A type and 2.25 for B type, whose difference was caused by the influence of the back-plates of butt-welded structures. The current results could provide important guidelines to determine the V-groove angle of butt-welded joints with a satisfactory fatigue life, although under severe operating conditions.

• 한국정밀공학회지
• /
• 제29권3호
• /
• pp.307-312
• /
• 2012

This study aims to investigate the effect of the post weld treatments on the fatigue life of T-type welded structure made by a SM50A steel material, generally used for excavators, because changes in the geometry, material and surface properties of welded regions affect the fatigue life of welded structures. T-type test specimens were prepared by the CO2 welding of rolled steel plates (SM50A steel) with a thickness of 10 mm at a welding speed of 30 cm/min and these Ttype welded specimens were further treated by UIT (Ultrasonic Impact Treatment) and/or toegrinding post welding treatment methods. In order to investigate improvements on the fatigue life of the samples. 3-point bending fatigue tests were conducted with a stress ratio of R=0.1 under a cyclic loading environment at a frequency of 5 Hz, via a hydraulic fatigue testing machine (${\pm}100\;kN$, MTS 809). The tests were performed at room temperature. The fatigue life of UIT specimens was approximately 25 times longer than that of as-welded specimens at a stress amplitude of 281 MPa, while toe-grinding specimens exhibited 4.15 times longer fatigue life. The current results could provide important guidelines to determine the proper post weld treatment methodologies of T-type welded parts for excavators with a satisfactory fatigue life although under severe operating conditions.

• 한국생활과학회지
• /
• 제16권5호
• /
• pp.1051-1059
• /
• 2007

This study intends to find out possible variations in physical properties and color of hair depending on dye type(acidic and alkalic) and permanent treatment/hair dyeing procedure. To meet the goals, healthy hair samples were taken from 5 women's hair speciment in 20's without experiencing in any harmful substance via long-term medications. and beauty care using chemicals. To get possible findings depending upon hair dye type and treatment procedure, both acidic and alkalic hair dye were applied on some specimens after permanent treatment, while on other specimens before permanent treatment. In order to determine scale damage, this study used SEM(Hitachi S-2500C) both hair thickness and tensile strength were measured with optical microscope(Nikon, MM-60/L3T) and Instron (4482-standard). Wave configuration was measured transverse and longitudinal round diameter. The chromaticity of each specimen was measured using a spectrocolorimeter(Color Techno System, JP/JX-777) with visual $C/2^{\circ}$ (at $2^{\circ}$ with C light source) monitor fixed to determine Lab and CMYK values. As a result, it was found that hair specimens were more significantly damaged with alkalic hair dye treatment than with acidic hair dye treatment, while hair specimens were more effectively dyed with the former hair dye type than with the latter one. For possible results depending on treatment procedure, it was found that hair specimens were less damaged but more effectively dyed with permanent treatment followed by hair dyeing than vice versa. Therefore, it was concluded that permanent treatment followed by acidic hair dyeing would be more effective in reducing hair damages.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.328-332
• /
• 1993

Single overload tests are carried out for SS41. Specimens are used hollow type and solid type that stress condition prevail plane stress and plane strain at surface crack. According to the crack initiation and propagation period, single overload applies to three regime and overload ratios change into 1.5, 2.0. Crack retardation zones at initation range aren't different in both specimens respectively, however at propagation range come into large scale in hollow specimen. Delayed load cycles come into large scale in solid type. And the more the overload ratio increase, the larger the retardation zone increase but the magnitude doesn't exactly equal to the expected from the overload ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.138-143
• /
• 2008

Recently, a new periodic cellular metal(PCM) named as Wire wove Bulk Kagome(WBK) was introduced. Based on the shape of tetrahedra composing a WBK, WBKs are classified into two types, namely, concave and convex type. They are easily differentiated by changing the assembling sequence. The effect of geometrical parameters such as the wire diameter, strut length and number of layers on the compressive behavior of concave type WBK has already been investigated. In this work, the similar works were performed with the convex type WBKs. It was shown that the compressive strength of the convex type WBK was quite similar to that of the concave type. The compressive strengths of convex type specimens also depend on the slenderness ratio, but a little different from those of concave type specimens in the detailed behavior. And densification occurs earlier than the concave type WBK.

• 터널과지하공간
• /
• 제7권3호
• /
• pp.221-229
• /
• 1997

Disc-type and ring-type specimens of four different materials were tested to investigate the tensile characteristics and their brief results are presented. Materials tested were marble, granite, cement mortar and plaster. Unizxial tensile strengths are compared with Brazilian and ring test strengths. It was found that Brazilian strengths were usually greater than uniaxial tensile strengths and affected by loading rates. In the ring tests, tensile strengths were generally found to be decreased as relative hole radius being increased. Ring test strengths, however, converged to some value in r$\geq$0.45 of marble, r$\geqq$0.29 of cement mortar and r$\leq$0.5 of plaster specimens. In such range of r, furthermore, transverse cracking of specimens were observed.

• Animal Systematics, Evolution and Diversity
• /
• 제33권1호
• /
• pp.17-25
• /
• 2017

Two marine gastrotrich species of the genus Acanthodasys, A. ericinus Lee, 2012 and A. comtus Lee, 2012, are taxonomically reconsidered. Both of them were originally described based on the specimens from intertidal or sublittoral sandy bottom of the Yellow Sea and Jeju Island, South Korea, and included in a monographical publication of in 2012. However, the description of them was quite insufficient, and designations of type specimens were entirely lacking. In this study, we make a subsequent designation of type specimens for the two Acanthodasys species, and carry out a full redescription of them with additional remarks on their morphological micro-characteristics by scanning electronic microscopy. Some brief nomenclatural notes on Korean marine gastrotrichs are also provided.