• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.968-973
• /
• 2012

Slam testing is a mandatory testing process to evaluate the fatigue resistance of a door plate module before delivering it to car makers. This process is very hard job to complete it since the testing facilities are considerably expensive and the required testing time is relatively very long, i.e. more than eight days for a single specimen. In this paper, an accelerated testing method of a door plate module is proposed using vibration test equipment instead of the current one by exposing to the critical excitation of a door glass. Under the proposed excitation method, the similar testing result can be evaluated within less than two hours. The suitability of the proposed testing method was demonstrated by comparing failure modes of both the current testing method and the proposed one.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.304-307
• /
• 2000

This paper presents a numerical simulation study for remote parallel pseudo-dynamic testings using Internet. In this testing method, experimental facilities located at different places can be parallelly used for testing a large-scale structure with many components subjected to severe nonlinear behavior. Example analysis is carried out on a base- isolated bridge for earthquake loading. The results indicate that the time required for data communication between two facilities located 250km apart through Internet for t 000 time steps is about 20 minutes, which is fairly equivalent to the time required for pseudo-dynamic testing. This testing method can be more powerful, as the data transmitting technique through Internet improves.

• Journal of Applied Reliability
• /
• v.17 no.2
• /
• pp.136-142
• /
• 2017

Purpose: In this paper, we propose a test method for evaluating the life time of the inverter which is one of the main internal configuration systems in order to evaluate the life time of the power supply for the vehicle. Methods: The performance and failure criteria required for the development of the accelerated life test method were established and the Taguchi method was used to derive the stress factors affecting performance and reliability. Results: The major stress of the product degradation were considered to be high temperature. Conclusion: The acceleration factor was estimated through a two-level high temperature test and a test methods was designed to guarantee the accelerated life time of the inverter.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.23 no.60
• /
• pp.73-81
• /
• 2000

The testing processes for VLSI finished devices are considerably complex because they require different types of ATE to be linked together. Due to the interaction effect between two or more linked ATEs, it is difficult to trace down the cause of the unexpected longer ATE setup time and random yields, which frequently occur in the VLSI circuit-testing laboratory. The goal of this paper is to develop and demonstrate the methodology designed to eliminate the possible interaction factors that might affect the random yields and/or unexpected longer setup time as well as increase the productivity. The statistical method such as design of experiment or multivariate analysis cannot be applied to the final testing floor here directly due to the environmental constraints. Expanded product data information (PDI) is constructed by combining product data information and ATE control information. An architecture utilizing expanded PDI is designed, which enables the engineer to conduct statistical approach investigation and reduce the setup time, as well as increase yield.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.6
• /
• pp.635-644
• /
• 2003

To ensure the reliability of ultrasonic nondestructive testing techniques for modern structural materials, the effects of anisotropy and inhomogeneity and the influence of non-planar component geometries on ultrasonic wave propagation have to be taken into account. In this article, fundamentals and applications of two analytical approaches to three-dimensional elastic beam field calculation are presented. Results for both isotropic materials including curved interfaces and for anisotropic media like composites are presented, covering field profiles for various types of transducers and the modeling of time-dependent rf-signals.

• Journal of the Korean Data and Information Science Society
• /
• v.14 no.2
• /
• pp.377-383
• /
• 2003

In this paper, we consider two components system in which the lifetimes follow the bivariate Pareto model with random censored data. We assume that the censoring time is independent of the lifetimes of the two components. We develop large sample tests for testing independence between two components. Also we present simulated study which is the test based on asymptotic normal distribution in testing independence.

• Journal of Korean Society for Quality Management
• /
• v.17 no.2
• /
• pp.17-26
• /
• 1989

This paper is concerned with forecasting the existing number of errors in the computer software and optimizing the stopping time of the software test based upon the forecasted number of errors. The most commonly used models have assessed software reliability under the assumption that the software failure late is proportional to the current fault content of the software but invariant to time since software faults are independents of others and equally likely to cause a failure during testing. In practice, it has been observed that in many situations, the failure rate decrease. Hence, this paper proposes a mathematical model to describe testing situations where the failure rate of software limearly decreases proportional to testing time. The least square method is used to estimate parameters of the mathematical model. A cost model to optimize the software testing time is also proposed. In this cost mode two cost factors are considered. The first cost is to test execution cost directly proportional to test time and the second cost is the failure cost incurred after delivery of the software to user. The failure cost is assumed to be proportional to the number of errors remained in the software at the test stopping time. The optimal stopping time is determined to minimize the total cost, which is the sum of test execution cast and the failure cost. A numerical example is solved to illustrate the proposed procedure.

• Proceedings of the Korean Reliability Society Conference
• /
• 2004.07a
• /
• pp.227-232
• /
• 2004

The failure of geogrids can be defined as an excessive creep strain which causes the collapse of slopes and embankments. In this study, the accelerated creep tests were applied to two different types of polyester geogrids, at 75, 80, 85$^{\circ}C$ by applying 50% load of ultimate tensile strengths using a newly designed test equipment which is allowed the creep testing at higher temperatures. And then the creep curves were shifted and superposed in the time axis by applying time-temperature supposition principles. In predicting the lifetimes of geogrids, the underlying distribution for failure times were determined based on identification of the failure mechanism. The results indicate that the conventional procedures with the newly designed test equipment are shown to be effective in prediction of the lifetimes of geogrids with shorter test times. In addition, the predicted lifetimes of geogrids having different structures at various creep strains give guidelines for users to select the proper geogrids in the fields.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.598-606
• /
• 1996

Computer testing system for pumps is an automatic measuring and testing system micro computer. There are two functions to this system. 1. Automatically controlling the testing processes. It includes controlling to testing devices, adjusting test points and starting or stopping the pump. 2. Automatically collecting and calculating the testing data. It includes the collection and calculation of the parameters to be measured, printing the testing reports and plotting the testing curves. When using it the measuring accuracy may be improved and the time for testing may be compressed by use the system . So it is used widely on the world. In this paper the basic construction and the work principle and the testing processes are described.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.14
• /
• pp.5993-5999
• /
• 2015

Background: Molecular testing for human papillomavirus (HPV) is the most objective and reproducible of all cervical cancer screening tests and also less demanding in terms of training and quality assurance. However, there is an impending need for cost effective molecular HPV testing methods with sampling ease, easy storage measures and minimum turn around times suitable for a low resource setting. Objective : Our aim was to evaluate the feasibility of using a fast transfer analysis (FTA) mini elute cartridge for cervical sampling to identify high risk HPV by real time PCR and to compare molecular HPV testing and Pap cytology testing to predict histologically confirmed cervical precancer (CIN 2+ lesions) in a cervical cancer prevention program. Materials and Methods: This was conducted as a pilot study (n=200) on women sampled using FTA mini elute cartridges, genotyped by two different real time PCR assays, detecting 13 high risk HPV (HR HPV) species, including HPV16 along with its physical DNA status. Results obtained from each of the tests were compared and analysed using suitable statistical tests. Results: With FTA mini elute cartridge samples HR HPV positivity was seen in 48/200 (24%). Of these, presence of HPV 16 DNA was observed in 28/48 (58.3%) women. High risk HPV was positive in 20% (37/185) of women with benign cytology and 73.3% (11/15) of women with abnormal cytology findings. A very significant correlation (${\chi}^2=22.090$ ; p=0.000) was observed between cytology and HR HPV findings showing an increasing trend of HR HPV prevalence in 50% (1/2) of LSIL, 75% (3/4) of HSIL and 100% (3/3) of SCC. Of the CIN 2+ lesions identified by histopathology, 88.9% (8/9) had HR HPV. A significant association (${\chi}^2=11.223$ ; p=0.001) of HR HPV and histopathologically confirmed CIN 2+ lesions was found. Sensitivity of the two tests were comparable but specificity of Pap testing was better (90.7% vs 70.4%) to predict histopathologically diagnosed cervical precancers. Conclusions: The current study explored the feasibility of using a FTA mini elute cartridge for cervical sampling for the first time in India as a part of a community based cervical cancer prevention program. We suggest that FTA based sampling is suitable and feasible for real time based HPV testing. Molecular HR HPV testing can be more sensitive and useful to identify high risk women requiring Pap testing which is more specific to detect histologically confirmed cervical precancer.