• Steel and Composite Structures
• /
• 제50권1호
• /
• pp.107-122
• /
• 2024

Following an internal column failure, adjacent double-span beams above the failed column will play a critical role in the load transfer and internal force redistribution within the remaining structure, and the span-to-depth ratios of double-span beams significantly influence the structural resistance capacity against progressive collapse. Most existing studies have focused on the collapse-resistant performances of single-story symmetric structures, whereas limited published works are available on the collapse resistances of multi-story steel frames with unequal spans. To this end, in this study, numerical models based on shell elements were employed to investigate the structural behavior of multi-story steel frames with unequal spans. The simulation models were validated using the previous experimental results obtained for single- and two-story steel frames, and the load-displacement responses and internal force development of unequal-span three-story steel frames under three cases were comprehensively analyzed. In addition, the specific contributions of the different mechanism resistances of unequal-span, double-span beams of each story were separated quantitatively using the energy equilibrium theory, with an aim to gain a deeper level of understanding of the load-resistance mechanisms in the unequal-span steel frames. The results showed that the axial and flexural mechanism resistances were determined by the span ratio and linear stiffness ratio of double-span beams, respectively.

• Steel and Composite Structures
• /
• 제21권1호
• /
• pp.177-194
• /
• 2016

The cable-supported ribbed beam composite slab structure (CBS) is a new type of pre-stressed hybrid structure. The standard construction method of CBS including five steps and two key phases are proposed in this paper. The theoretical analysis and experimental research on a 1:5 scaled model were carried out. First, the tensioning construction method based on deformation control was applied to pre-stress the cables. The research results indicate that the actual tensile force applied to the cable is slightly larger than the theoretical value, and the error is about 6.8%. Subsequently, three support dismantling schemes are discussed. Scheme one indicates that each span of CBS has certain level of mechanical independence such that the construction of a span is not significantly affected by the adjacent spans. It is shown that dismantling from the middle to the ends is an optimal support dismantling method. The experimental research also indicates that by using this method, the CBS behaves identically with the numerical analysis results during the construction and service.

• 한국공간구조학회논문집
• /
• 제18권3호
• /
• pp.57-66
• /
• 2018

Recently various composite beams in which concrete is filled in the U-shaped steel plate have been developed for saving story height and reducing construction period. Due to the high flexural stiffness and strength, they are widely being used for the building with large loads and long spans. The semi-slim AU composite beam has proven to take highly improved stability compared to the existing composite beams, because it consists of the closed steel section by attaching cap-type shear connectors to the upper side of U-shaped steel plate. In this study the finite element analyses were performed to evaluate the safety of the AU composite beam with unconsolidated concrete which were sustained through the closed steel section during the construction phase. The analyses were performed on the two types of cross section applied to the fabrication of AU composite beams, and the results were compared to the those of 2-point bending tests. In addition, the flexural performance according to the space of intermittent cap-type shear connectors and the location of reinforcing steel bars for compression was comparatively investigated. Through the results of analytical studies, it is preferable to adopt the yield moment of AU composite beam for evaluating the safety in the construction phase, and to limit the space of intermittent shear connectors to 400 mm or less for the construction load.

• Structural Monitoring and Maintenance
• /
• 제5권4호
• /
• pp.463-488
• /
• 2018

In the last decades, research efforts have been spent to investigate the effect of prestressing on the dynamic behaviour of prestressed concrete (PSC) beams. Whereas no agreement has been reached among the achievements obtained by different Researchers and among the theoretical and the experimental results for simply supported beams, very few researches have addressed this problem in continuous PSC beams. This topic is, indeed, worthy of consideration bearing in mind that many relevant bridges and viaducts in the road and railway networks have been designed and constructed with this structural scheme. In this paper the attention is, thus, focused on the dynamic features of continuous PSC bridges taking into account the effect of prestressing. This latter, in fact, contributes to the modification of the distribution of the bending stress along the beam, also by means of the secondary moments, and influences the flexural stiffness of the beam itself. The dynamic properties of a continuous, two spans bridge connected by a nonlinear spring have been extracted by solving an eigenvalue problem in different linearized configurations corresponding to different values of the prestress force. The stiffness of the nonlinear spring has been calculated considering the mechanical behaviour of the PSC beam in the uncracked and in the cracked stage. The application of the proposed methodology to several case studies indicates that the shift from the uncracked to the cracked stage due to an excessive prestress loss is clearly detectable looking at the variation of the dynamic properties of the beam. In service conditions, this shift happens for low values of the prestress losses (up to 20%) for structure with a high value of the ratio between the permanent load and the total load, as happens for instance in long span, continuous box bridges. In such conditions, the detection of the dynamic properties can provide meaningful information regarding the structural state of the PSC beam.

• 한국전산구조공학회논문집
• /
• 제29권3호
• /
• pp.269-275
• /
• 2016

본 논문은 유공형 판 형태로 전단 보강한 넓은 보의 중심에 기둥을 삽입하여 연속한 두 경간으로 설계하여 전단파괴 실험을 통해 넓은 보의 거동을 평가하였다. 유공형 강판으로 전단 보강된 시험체 5개와 유공형 GFRP판으로 보강된 시험체 3개 총 8개의 시험체를 전단파괴 실험을 통해 계측한 전단강도와 ACI-318 규준의 설계식을 통해 얻은 전단강도와 비교 평가하였다. 또한 넓은 보의 지지부 폭, 지지부의 형상과 전단보강재의 재료를 변수로 하여 넓은 보의 전단강도에 미치는 영향을 분석하였다. 이를 통해 지지부 폭이 증가할수록 전단강도가 증가하고 하중의 집중을 방지하는 것을 확인하였다. 또한 전단보강재의 재료인 강재와 GFRP에 상관없이 전단보강량이 동일하다면 넓은 보에서 비슷한 전단보강효과를 보이는 것을 확인하였다.

• 소음진동
• /
• 제8권6호
• /
• pp.1166-1171
• /
• 1998

본 연구에서는 이웃한 두 경간 사이에 있는 질량과 강성을 갖는 연결기가 모드편재에 미치는 영향을 해석적으로 분석하고 수치예제를 통해 그 결과를 검증하였다. 연결기의 강성이 구조물의 모든 고유모드를 모드편재에 민감하게 만드는 반면 연결기의 질량은 고차모드의 민감도를 심각히 증가시킨다. 또한 본 연구에서는 일부 고유모드에서 새로운 형태의 반편재현상을 관찰하였다. 반편재현상이 발생하는 모드에서는 경간 사이의 연성이 매우 약하고 구조 변화가 심각하게 발생하더라도 모드편재 현상이 발생하지 않거나 발생하더라도 매우 미약하게 나타난다. 해석적 분석에서는 연결기를 사이에 두고 있는 두개의 부구조물을 단순화 시킨 강성-질량 시스템을 대상으로 하였다. 수치예제에서는 중간 지점에 회전강성과 회전질량을 갖으며 단순지지된 이경간 연속보를 해석하였다.

• 한국강구조학회 논문집
• /
• 제23권2호
• /
• pp.199-210
• /
• 2011

사장교의 케이블은 타 부재에 비해 단면적이 매우 작고 고응력 상태이므로 진동에 매우 민감한 부재이다. 따라서 사장교 케이블의 충격계수는 실제 차량의 주행으로 발생하는 동적 효과를 반영하여 평가하는 것이 합리적이다. 이에 본 연구에서는 차량 중량, 케이블 모델, 노면조도, 차량속도 및 차량간격의 설계변수를 고려하여 중앙경간 230m 및 540m의 강합성 사장교를 대상으로 차량 이동하중 해석을 수행하여 케이블의 충격계수를 평가하고, 현재 실무에서 사용되고 있는 영향선을 이용한 방법과 비교하였다. 본 연구에 사용된 노면조도는 ISO 8608 규정에 근거하여 랜덤 생성하였으며, 생성 회수에 따른 케이블 충격계수의 수렴 추이를 분석함으로써 결과의 신뢰도를 확보하였다. 또한, 차량모델은 9-자유도를 갖는 트랙터-트레일러 형식의 트럭 모델을 적용하였으며 차량의 운동방정식은 Lagrange운동방정식으로부터 유도하였다. 해석 대상 교량은 3차원 유한요소모델로 구축하였으며 보강형과 주탑은 보요소, 케이블은 등가탄성계수를 갖는 트러스요소를 사용하였다. 이동하중으로 인한 교량-차량 상호작용 해석에는 직접적분법을 사용하였으며, 교량의 변위 오차율이 허용 범위 내에 수렴될 때까지 반복 해석을 수행하였다. 그 결과, 실제 차량의 주행으로 발생하는 동적 효과를 고려하지 못하는 영향선 기법은 차량 이동하중 해석에 비해 측경간 단부 케이블의 충격계수를 과소평가할 수 있는 것으로 나타났다.

• Structural Engineering and Mechanics
• /
• 제71권1호
• /
• pp.57-63
• /
• 2019

During the last two decades, much joint research regarding vibration based methods has been done, leading to developing various algorithms and techniques. These algorithms and techniques can be divided into modal methods and signal methods. Although modal methods have been widely used for health monitoring and damage detection, signal methods due to higher efficiency have received considerable attention in various fields, including aerospace, mechanical and civil engineering. Signal-based methods are derived directly from the recorded responses through signal processing algorithms to detect damage. According to different signal processing techniques, signal-based methods can be divided into three categories including time domain methods, frequency domain methods, and time-frequency domain methods. The frequency domain methods are well-known and interest in using them has increased in recent years. To determine dynamic behaviours, to identify systems and to detect damages of bridges, different methods and algorithms have been proposed by researchers. In this study, a new algorithm to detect seismic damage in the bridge's piers is suggested. To evaluate the algorithm, an analytical model of a bridge with simple spans is used. Based on the algorithm, before and after damage, the bridge is excited by a sine force, and the piers' responses are measured. The dynamic specifications of the bridge are extracted by Power Spectral Density function. In addition, the Least Square Method is used to detect damage in the bridge's piers. The results indicate that the proposed algorithm can identify the seismic damage effectively. The algorithm is output-only method and measuring the excitation force is not needed. Moreover, the proposed approach does not need numerical models.

• 수산해양기술연구
• /
• 제42권1호
• /
• pp.30-37
• /
• 2006

Black rockfish and goldeye rockfish are commercially important fish species due to the increasing demand in Korea. When estimating the abundance of stocks for these species acoustically, it is of crucial importance to know the target strength(TS) to length dependence. In relation to these needs, TS measurement was conducted on black rockfish and goldeye rockfish in an acrylic salt water tank using 70kHz and 120kHz split beam echo sounders. The TS for these two species under the controlled condition was simultaneously measured with the swimming movement by DVR system and analyzed as a function of fish length(L). The results obtained are summarized as follows: The best fit regression of TS on fish length of black rockfish was TS=19.38 Log(L, cm)-70.46 ($r^2=0.71$) at 70kHz and TS=22.39 Log(L, cm)-70.40 ($r^2=0.64$) at 120kHz and in the standard form TS=20 Log(L, cm)-71.29 ($r^2 = 0.70$) at 70kHz and TS=20 Log(L, cm)-66.88 ($r^2=0.57$) at 120kHz. The best fit regression of TS on fish length of goldeye rockfish was TS=17.10 Log(L, cm)-68.28 ($r^2=0.37$) at 70kHz and TS=24.39 Log(L, cm)-73.74 ($r^2=0.59$) at 120kHz and in the standard form TS=20 Log(L, cm)-72.03 ($r^2=0.32$) at 70kHz and TS=20 Log(L, cm)-67.68 ($r^2=0.64$) at 120kHz. An empirical model for fish TS(dB) averaged over the dorsal aspect of 115 fishes of black rockfish and goldeye rockfish and which spans the fish length(L, m) to wavelength($\lambda$, m) ratio between 8 and 30 was derived : TS=34.12 Log(L)-14.12 Log($\lambda$)-23.83, ($r^2=0.90$).

• Steel and Composite Structures
• /
• 제6권6호
• /
• pp.459-477
• /
• 2006

A theoretical research project is undertaken to develop integrated analysis and design tools for long span composite beams in modern high-rise buildings, and it aims to develop non-linear finite element models for practical design of composite beams. As the first paper in the series, this paper presents the development study as well as the calibration exercise of the proposed finite element models for simply supported composite beams. Other practical issues such as continuous composite beams, the provision of web openings for passage of building services, the partial continuity offered by the connections to columns as well as the behaviour of both unprotected and protected composite beams under fires will be reported separately. In this paper, details of the finite elements and the material models for both steel and reinforced concrete are first described, and finite element studies of composite beams with full details of test data are then presented. It should be noted that in the proposed finite element models, both steel beams and concrete slabs are modelled with two dimensional plane stress elements whose widths are assigned to be equal to the widths of concrete flanges, and the flange widths and the web thicknesses of steel beams as appropriate. Moreover, each shear connector is modelled with one horizontal spring and one vertical spring to simulate its longitudinal shear and pull-out actions based on measured load-slippage curves of push-out tests of shear connectors. The numerical results are then carefully analyzed and compared with the corresponding test results in terms of load mid-span deflection curves as well as load end-slippage curves. Other deformation characteristics of the composite beams such as stress and strain distributions across the composite cross-sections as well as distributions of shear forces and slippages in shear connectors along the beam spans are also examined in details. It is shown that the numerical results of the composite beams compare well with the test data in terms of various load-deformation characteristics along the entire deformation ranges. Hence, the proposed analysis and design tools are considered to be simple and yet effective for composite beams with practical geometrical dimensions and arrangements. Structural engineers are strongly encouraged to employ the models in their practical work to exploit the full advantages offered by composite construction.