• Journal of Biosystems Engineering
• /
• 제34권4호
• /
• pp.205-210
• /
• 2009

It has been known from Willoughby's empirical equation that rating cone index can be determined if wheel sinkage and slip of a vehicle can be measured on soil surface. A field data of wheel sinkage and slip was collected from two tractors of different sizes on gravelly sand and gravelly loamy sand. Using the data, rating cone index of the soil was estimated. The estimated rating cone index demonstrated that it could be determined in real time by measuring wheel sinkage and slip. It was also demonstrated statistically that the same soil strength could be obtained under the same soil conditions regardless of the vehicle platforms used for the wheel sinkage and slip measurements.

• 디지털산업정보학회논문지
• /
• 제9권1호
• /
• pp.73-78
• /
• 2013

In this paper, configuration control for the Horizontal Maintenance of the 2 wheel robot has been studied using ARS(Attitude Refrence System). The 2 wheel robot technique is getting attention and there have been many researches on the seg-way since the US. Using its 2 freedom, a 2 wheel robot can move in various modes and Our robot performs goal reaching ARS.2 wheel robot fall down to the forward or reverse direction to converge to the stable point. Kalman Filter is normally used for the algorithm and numerous research is progressing at the moment. To calculate the attitude in ARS using 2 axis gyro(roll, pitch) and 3 axis accelerometers (x, y, z). In this paper we present a two wheel robot system for an autonomous mobile robot. This paper realized the robot control method which is much simpler but able to get desired performance by using the ARS control.

• 전기학회논문지
• /
• 제62권6호
• /
• pp.750-755
• /
• 2013

In-wheel motor system gets the driving force from direct-driven motor in the wheel of electric vehicle. It is known as good system for vehicles, from an efficiency, packaging, handling and safety. This paper describes motor and inverter technologies, system configuration and control algorithms for in-wheel type electric vehicle. It is necessary to control on an interrelation perspective because this system drives two motors at same time. In system design, IPMSM(Interior Permanent Magnet Synchronous Motor) including a wide operating range and high-speed rpm is used and flux weakening control is performed in constant power range. Under the torque command from the host controller, auto control box, inverter's output torque is calculated with using torque estimation technique and applied to actual vehicle driving system. It is verified that the configuration and the algorithm are suitable for the in-wheel motor system.

• Smart Structures and Systems
• /
• 제23권4호
• /
• pp.347-357
• /
• 2019

A new methodology for mitigation of the wheel squealing is proposed and investigated based on the dithering control. The idea can be applied in railway lines particularly in urban areas. The idea is clearly presented, and applied to a validated model. A full-scale model including the vehicle, curved track and wheel/rail contact is developed in the time domain to analyze the possibility and level of wheel squeal noise. Comparing the numerical results with a field test, the model is validated in different levels namely i) occurrence, ii) squealing frequency and iii) noise level. Two different approaches are proposed a) dithering of the wheel with piezoelectric patches and b) dithering of the rail with piezoelectric stacks. The noise level as well as the wheel responses is compared after applying the control strategy. A parametric study is carried out and effect of the dithering voltage and frequency on the squealing noise is investigated. It is found that both the strategies perform quite effectively within the saturating threshold of piezoelectric actuators.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.1-14
• /
• 2013

In this paper, a finite element analysis technique of rolling stock models for collision-induced derailments was suggested using rolling contacts for wheel-rail interaction. The collision-induced derailments of rolling stock can be categorized into two patterns of wheel-climb and wheel-lift according to the friction direction between wheel flange and rail. The wheel-climb derailment types are classified as Climb-up, Climb/roll-over and Roll-over-C types, and the wheel-lift derailment types as Slip-up, Slip/roll-over and Roll-over-L types. To verify the rolling contact simulations for wheel-rail interaction, dynamic simulations of a single wheelset using Recurdyn of Functionbay and Ls-Dyna of LSTC were performed and compared for the 6-typical derailments. The collision-induced derailment simulation of the finite element model of KHST (Korean High Speed Train) was conducted and verified using the theoretical predictions of a simplified wheel-set model proposed for each derailment type.

• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.13-19
• /
• 2010

A design method of railway wheel profile with objective function of equivalent conicity considering wheel dimension constraint, two points contact problem between wheel and rail was proposed. New design method shows good results. New wheel profile generated from optimization process shows better dynamic performance compared with initial profile as the purpose of wheel profile design. And to verify the design method with testing the stability of new wheel profile, we conducted a critical speed test for new wheel profile using scale model applied scaling method of railway vehicle dynamics. The result of critical speed test show good agreement with that of numerical analysis. From the above results, it is seen that the design method with objective function of equivalent conicity is feasible and it could be applied to design new wheel profile efficiently.

• 대한기계학회논문집A
• /
• 제37권11호
• /
• pp.1387-1395
• /
• 2013

차륜 불평형은 차륜의 무게중심이 윤축의 기하학적 중심축에서 벗어나 있을 때 발생한다. 차륜 불평형을 수정하지 않고 주행하면 불평형에 의한 원심력이 차체의 진동을 발생시키게 되며 차륜의 마모를 촉진시키거나 차축 베어링에 손상을 주게 된다. 본 연구에서는 철도차량 동적해석을 통하여 차륜 불평형이 차량 임계속도와 차체 진동에 미치는 영향을 검토하였다. 차륜 불평형은 임계속도를 감소시키고 차체 공진을 유발할 수 있음을 알 수 있었다. 또한 차륜의 정적, 동적 불평형에 따른 차체진동을 해석함으로써 불평형 수정은 양면 밸런싱이 필요함을 밝혔다.

• Journal of Ceramic Processing Research
• /
• 제23권4호
• /
• pp.436-442
• /
• 2022

Gallium nitride (GaN) substrates were ground in two different grinding wheel abrasive sizes of 270 and 800-mesh, and thechange in surface morphologies of the substrates and the depth of subsurface damage (SSD) were observed. With the 800-meshgrinding wheel, the surface roughness (SR) and the depth of SSD of the sample tended to decrease, which was not the casewith the 270-mesh grinding wheel. In the X-ray rocking curve, the sample exhibited some compressive stress with the 270-meshgrinding wheel, but with the 800-mesh grinding wheel, it demonstrated the occurrence of tensile stresses in the sample and adecrease in full width at half maximum (FWHM), which confirms an improvement in the crystallinity. In the Raman spectra,the compressive stress of the 270-mesh grinding wheel and the tensile stress of the 800-mesh grinding wheel were confirmedthrough peak shifts. Photoluminescence (PL) spectra confirmed that the intensity ratio of the yellow luminescence increasedat the 800-mesh grinding wheel, and a blue shift occurred further. These results indicate that the SR and the depth of SSDwere proportional to the abrasive grain size of the grinding wheel. At the same time, the increase in PL intensity at specificpeak positions indicates that the stress stemming from the grinding process was concentrated at the crystal surface. The abovemechanism is illustrated in a schematic diagram, which confirms the possibility of improving the grinding efficiency andsubsequent polishing processes in future applications.

• 한국자동차공학회논문집
• /
• 제3권3호
• /
• pp.66-78
• /
• 1995

In this paper, we address vehicle modeling and dynamic analysis of four wheel steering systems (4WS). 4WS is one of the devices used for the improvement of vehicle maneuverability and stability. All research done here is based on a production vehicle from a manufacturer. To study actual system response, a three dimensional, full vehicle model was created. In past research of this type, simple, two dimensional, bicycle vehicle models were typically used. First, we modelled and performed a dynamic analysis on a conventional two wheel steering(2WS) vehicle. The modeling and analysis for this model and subsequent 4WS vehicles were performed using ADAMS(Automatic Dynamic Analysis of Mechanical Systems) software. After the original vehicle model was verified with actual experiment results, the rear steering mechanism for the 4WS vehicle was modelled and the rear suspension was changed to McPherson-type forming a four wheel independent suspension system. Three different 4WS systems were analyzed. The first system applied a mechanical linkage between the front and rear steering mechanisms. The second and third systems used, simple control logic based on the speed and yaw rate of the vehicle. 4WS vehicle proved dynamic results through double lane change test.

• 한국생산제조학회지
• /
• 제22권6호
• /
• pp.1010-1017
• /
• 2013

Two-axial electrodynamic forces generated on a conductive plate by a partially shielded magnet wheel are strongly coupled through the rotational speed of the wheel. To control the spatial position of the plate using magnet wheels, the forces should be handled independently. Thus, three methods are proposed in this paper. First, considering that a relative ratio between two forces is independent of the length of the air-gap from the top of the wheel, it is possible to indirectly control the in-plane position of the plate using only the normal forces. In doing so, the control inputs for in-plane motion are converted into the target positions for out-of-plane motion. Second, the tangential direction of the open area of the shield plate and the rotational speed of the wheel become the new control variables. Third, the absolute magnitude of the open area is varied, instead of rotating the open area. The forces are determined simply by using a linear controller, and the relative ratio between the forces creates a unique wheel speed. The above methods were verified experimentally.